Buffered bulk mode is intended for bulk *input* endpoints, where the data is
of a streaming nature (not part of a command-response protocol). These
endpoints' input buffer may overflow if data is not read quickly enough.
So in buffered bulk mode the usb-host takes care of the submitting and
re-submitting of bulk transfers.

Buffered bulk mode is necessary for reliable operation with the bulk in
endpoints of usb to serial convertors. Unfortunatelty buffered bulk input
mode will only work with certain devices, therefor this patch also adds a
usb-id table to enable it for devices which need it, while leaving the
bulk ep handling for other devices unmodified.

Note that the bumping of the required usbredir from 0.5.3 to 0.6 does
not mean that we will now need a newer usbredir release then qemu-1.3,
.pc files reporting 0.5.3 have only ever existed in usbredir builds directly
from git, so qemu-1.3 needs the 0.6 release too.

Changes in v2:
-Split of quirk handling into quirks.c
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Add EHCI USB host controller to exynos4210.
Signed-off-by: NLiming Wang <walimisdev@gmail.com>
Signed-off-by: NAndreas Färber <andreas.faerber@web.de>
Reviewed-by: NIgor Mitsyanko <i.mitsyanko@samsung.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

It uses a different capsbase and opregbase than the Xilinx device.
Signed-off-by: NLiming Wang <walimisdev@gmail.com>
Signed-off-by: NAndreas Färber <andreas.faerber@web.de>
Cc: Igor Mitsyanko <i.mitsyanko@samsung.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

This allows specific derived models to use different values.
Signed-off-by: NAndreas Färber <andreas.faerber@web.de>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

SysBus EHCI was introduced in a hurry before 1.3 Soft Freeze.
To use QOM casts in place of DO_UPCAST() / FROM_SYSBUS(), we need an
identifying type. Introduce generic abstract base types for PCI and
SysBus EHCI to allow multiple types to access the shared fields.

While at it, move the state structs being amended with macros to the
header file so that they can be embedded.

The VMSTATE_PCI_DEVICE() macro does not play nice with the QOM
parent_obj naming convention, so defer that cleanup.
Signed-off-by: NAndreas Färber <andreas.faerber@web.de>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Due to the way devices are addressed with xhci (done by hardware, not
the guest os) there is no packet when invoking the set-address control
request.  Create a dummy packet in that case to avoid null pointer
dereferences.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

The xhci-hcd may submit bulk transfers > 65535 bytes even when not using
bulk-in pipeling, so usbredir can only be used in combination with an xhci
hcd if the client has the 32 bits bulk length capability.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

To ensure that interrupt receiving is properly stopped when the guest is
no longer interested in an interrupt endpoint.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Some usb devices (host or network redirection) can benefit from knowing when
the guest stops using an endpoint. Redirection may involve submitting packets
independently from the guest (in combination with a fifo buffer between the
redirection code and the guest), to ensure that buffers of the real usb device
are timely emptied. This is done for example for isoc traffic and for interrupt
input endpoints. But when the (re)submission of packets is done by the device
code, then how does it know when to stop this?

For isoc endpoints this is handled by detecting a set interface (change alt
setting) command, which works well for isoc endpoints. But for interrupt
endpoints currently the redirection code never stops receiving data from
the device, which is less then ideal.

However the controller emulation is aware when a guest looses interest, as
then the qh for the endpoint gets unlinked (ehci, ohci, uhci) or the endpoint
is explicitly stopped (xhci). This patch adds a new ep_stopped USBDevice
method and modifies the hcd code to call this on queue unlink / ep stop.

This makes it possible for the redirection code to properly stop receiving
interrupt input (*) data when the guest no longer has interest in it.

*) And in the future also buffered bulk input.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

usb_ep_find_packet_by_id mistakenly only checks the first packet and if that
is not a match, keeps trying the first packet! This patch fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

This leads to cleaner code in usb-hid, and removes up to a 1000 calls / sec to
qemu_get_clock_ns(vm_clock) if idle-time is set to its default value of 0.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

If somehow we've gotten behind a lot, simply skip ahead, like the ehci code
does.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Before this patch uhci would process an unlimited amount of frames when
behind on schedule, by setting the timer to a time already past, causing the
timer subsys to immediately recall the frame_timer function gain.

This would cause invalid cancellations of bulk queues when the catching up
processed more then 32 frames at a moment when the bulk qh was temporarily
unlinked (which the Linux uhci driver does).

This patch fixes this by processing maximum 16 frames in one go, and always
setting the timer one ms later, making the code behave more like the ehci
code.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Rather then using the magic 32 value in various places.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Re-arrange how we process frames / increase frnum / report pending interrupts,
to avoid a 1 ms delay in interrupt reporting to the guest. This increases
the packet throughput for cases where the guest submits a single packet,
then waits for its completion then re-submits from 500 pkts / sec to
1000 pkts / sec. This impacts for example the use of redirected / virtual
usb to serial convertors.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

ehci_raise_irq(s, USBSTS_PCD), gets applied immediately so there is no need
to call commit_irq after it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

I tried lowering the time between raising an interrupt and rescanning the
async schedule to see if the guest has queued a new transfer before, but
that did not have any positive effect. I now believe the cause for this is
that lowering this time made it more likely to hit the 1 ms interrupt
threshold penalty for the next packet, as described in my
"ehci: Use uframe precision for interrupt threshold checking" commit.

Now that we do interrupt threshold handling with uframe precision, futher
lowering this time from .5 to .25 ms gives an extra 15% improvement in speed
(MB/s) reading from a simple USB-2.0 thumb-drive.

While at it also properly set the int_req_by_async flag for short packet
completions.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Before this patch, the following could happen:
1) Transfer completes, raises interrupt
2) .5 ms later we check if the guest has queued up any new transfers
3) We find and execute a new transfer
4) .2 ms later the new transfer completes
5) We re-run our frame_timer to write back the completion, but less then
   1 ms has passed since our last run, so frindex is not changed, so the
   interrupt threshold code delays the interrupt
6) 1 ms from the re-run our frame-timer runs again and finally delivers
   the interrupt

This leads to unnecessary large delays of interrupts, this code fixes this
by changing frindex to uframe precision and using that for interrupt threshold
control, making the interrupt fire at step 5 for guest which have low interrupt
threshold settings (like Linux).

Note that the guest still sees the frindex move in steps of 8 for migration
compatibility.

This boosts Linux read speed of a simple cheap USB thumb drive by 6 %.

Changes in v2:
-Make the guest see frindex move in steps of 8 by modifying ehci_opreg_read,
 rather then using a shadow variable
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

ehci_fill_queue assumes that there is a one on one relationship between an ep
and a qh, this patch adds a check to ensure this.

Note I don't expect this to ever trigger, this is just something I noticed
the guest might do while working on other stuff. The only way this check can
trigger is if a guest mixes in and out qtd-s in a single qh for a non
control ep.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Remove the short-circuiting of fetchqtd in fetchqh, so that the
qtd gets properly verified before completing the transaction.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

No other changes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

This is not allowed, except for clearing active on cancellation, so don't
warn when the new token does not have its active bit set.

This unifies the cancellation path for modified qtd-s, and prepares
ehci_verify_qtd to be used ad an extra check inside
ehci_writeback_async_complete_packet().
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Also drop the warning printf, which was there mainly because this was an
untested code path (as the previous bug fixes to it show), but that no
longer is the case now :)
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

This reverts commit 9807cacc.
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Remove byte swaps by declaring the config space
as native endian.
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Add support for compiling for GCOV test coverage, enabled
with '--enable-gcov' during configure.

Test coverage will be reported after each test.
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

pc-testdev.c cannot be compiled with MinGW (and other non POSIX hosts):

  CC    i386-softmmu/hw/i386/../pc-testdev.o
qemu/hw/i386/../pc-testdev.c:38:22: warning: sys/mman.h: file not found
qemu/hw/i386/../pc-testdev.c: In function ‘test_flush_page’:
qemu/hw/i386/../pc-testdev.c:103: warning: implicit declaration of function ‘mprotect’
...
Signed-off-by: NStefan Weil <sw@weilnetz.de>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

The interface to normalizeRoundAndPackFloat64 requires that the
high bit be clear.  Perform one shift-right-and-jam if needed.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

* stefanha/trivial-patches:
  spice: drop incorrect vm_change_state_handler() opaque
  linux-user/syscall.c: remove forward declarations
  hw/mcf5206: Reduce size of lookup table
  Remove --sparc_cpu option from the configure list
  pseries: Remove unneeded include statement (fixes MinGW builds)
  pc_sysfw: Check for qemu_find_file() failure
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

* kraxel/testdev.1:
  pc: remove bochs bios debug ports
  hw: Add test device for unittests execution
  add isa-debug-exit device.
  switch debugcon to memory api
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

* kraxel/acpi.2:
  apci: assign memory regions to ich9 lpc device
  apci: assign memory regions to piix4 acpi device
  acpi: autoload dsdt
  configure: also symlink *.aml files
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>