Implement the MSR (immediate) instructions, which can update the
PSTATE SP and DAIF fields.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

To avoid complication in code that otherwise would not need to
care about whether EL1 is AArch32 or AArch64, we should store
the interrupt mask bits (CPSR.AIF in AArch32 and PSTATE.DAIF
in AArch64) in one place consistently regardless of EL1's mode.
Since AArch64 has an extra enable bit (D for debug exceptions)
which isn't visible in AArch32, this means we need to keep
the enables in env->pstate. (This is also consistent with the
general approach we're taking that we handle 32 bit CPUs as
being like AArch64/ARMv8 CPUs but which only run in 32 bit mode.)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the WFI instruction for A64; this just involves wiring
up the instruction, and adding a gen_a64_set_pc_im() which was
accidentally omitted from the A64 decoder top loop.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Emit the correct MMU index information for loads and stores from
A64 code, rather than hardwiring it to "always kernel mode",
by storing the exception level in the TB flags, and make
cpu_mmu_index() return the right answer when the CPU is in
AArch64 mode.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Define a dummy version of the AArch64 OSLAR_EL1 system register
which just ignores writes. Linux will always write to this (it
is the OS lock used for debugging), but we don't support debug.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

In AArch64 the breakpoint and watchpoint registers are mandatory, so the
kernel always accesses them on bootup. Implement dummy versions, which
read as written but have no actual effect.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64-specific ID and feature registers. Although
many of these are currently not used by the architecture (and so
always zero for all implementations), we define the full set of
fields in the ARMCPU struct for symmetry.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 view of the generic timer system registers.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Implement the AArch64 MPIDR system register.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 TTBR* registers. For v7 these were already 64 bits
to handle LPAE, but implemented as two separate uint32_t fields.
Combine them into a single uint64_t which can be used for all purposes.
Since this requires touching every use, take the opportunity to rename
the field to the architectural name.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the A64 view of the VBAR system register.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 TCR_EL1, which is the 64 bit view of
the AArch32 TTBCR. (The uses of the bits in the register are
completely different, but in any given situation the CPU will
always interpret them one way or the other. In fact for QEMU EL1
is always 64 bit, but we share the state field because this
is the correct mapping to permit a future implementation of EL2.)
We also make the AArch64 view the 'master' as far as migration
and reset is concerned.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 view of the system control register SCTLR_EL1.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 memory attribute registers. Since QEMU doesn't
model caches it does not need to care about memory attributes at all,
and we can simply make these read-as-written.

We did not previously implement the AArch32 versions of the MAIR
registers, which went unnoticed because of the overbroad TLB_LOCKDOWN
reginfo definition; provide them now to keep the 64<->32 register
relationship clear.

We already provided AMAIR registers for 32 bit as simple RAZ/WI;
extend that to provide a 64 bit RAZ/WI AMAIR_EL1.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

We don't support letting the guest do debug, but Linux prods the
monitor debug system control register anyway, so implement a dummy
RAZ/WI version.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 TLB invalidate operations. This is
the full set of TLBI ops defined for a CPU which doesn't
implement EL2 or EL3.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Implement all the AArch64 cache invalidate and clean ops
(which are all NOPs since QEMU doesn't emulate the cache).
The only remaining unimplemented cache op is DC ZVA.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the AArch64 view of the MIDR system register
(for AArch64 it is a simple constant, unlike the complicated
mess that TI925 imposes on the 32-bit view).
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Implement the CurrentEL sysreg.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

Make the cache ID system registers (CLIDR, CSSELR, CCSIDR, CTR)
visible to AArch64. These are mostly simple 64-bit extensions of the
existing 32 bit system registers and so can share reginfo definitions.
CTR needs to have a split definition, but we can clean up the
temporary user-mode implementation in favour of using the CPU-specified
reset value, and implement the system-mode-required semantics of
restricting its EL0 accessibility if SCTLR.UCT is not set.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>

The raw read and write functions were using the ARM_CP_64BIT flag in
ri->type to determine whether to treat the register's state field as
uint32_t or uint64_t; however AArch64 register info structs don't use
that flag. Abstract out the "how big is the field?" test into a
function and fix it to work for AArch64 registers. For this to work
we must ensure that the reginfo structs put into the hashtable have
the correct state field for their use, not the placeholder STATE_BOTH.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Save and restore the ARM KVM VGIC state from the kernel.  We rely on
QEMU to marshal the GICState data structure and therefore simply
synchronize the kernel state with the QEMU emulated state in both
directions.

We take some care on the restore path to check the VGIC has been
configured with enough IRQs and CPU interfaces that we can properly
restore the state, and for separate set/clear registers we first fully
clear the registers and then set the required bits.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687921-26921-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Support creating the ARM vgic device through the device control API and
setting the base address for the distributor and cpu interfaces in KVM
VMs using this API.

Because the older KVM_CREATE_IRQCHIP interface needs the irq chip to be
created prior to creating the VCPUs, we first test if we can use the
device control API in kvm_arch_irqchip_create (using the test flag from
the device control API).  If we cannot, it means we have to fall back to
KVM_CREATE_IRQCHIP and use the older ioctl at this point in time.  If
however, we can use the device control API, we don't do anything and
wait until the arm_gic_kvm driver initializes and let that use the
device control API.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-5-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Introduces two simple functions:
    int kvm_device_ioctl(int fd, int type, ...);
    int kvm_create_device(KVMState *s, uint64_t type, bool test);

These functions wrap the basic ioctl-based interactions with KVM in a
way similar to other KVM ioctl wrappers.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-4-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Introduce kvm_arch_irqchip_create an arch-specific hook in preparation
for architecture-specific use of the device control API to create IRQ
chips.

Following patches will implement the ARM irqchip create method to prefer
the device control API over the older KVM_CREATE_IRQCHIP API.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Update to tag v3.14-rc3 (6d0abeca3242a88cab8232e4acd7e2bf088f3bc2)
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

The GIC_SET_LEVEL macro unfortunately overwrote the entire level
bitmask instead of just or'ing on the necessary bits, causing active
level PPIs on a core to clear PPIs on other cores.

Cc: qemu-stable@nongnu.org
Reported-by: NRob Herring <rob.herring@linaro.org>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Message-id: 1393031030-8692-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

In ARMv5 level 2 page table descriptors, each 4K or 64K page is split into
four subpages, each of which can have different access permission settings,
which are specified by four two-bit fields in the l2 descriptor. A
long-standing cut-and-paste error meant we were using the wrong bits in
the virtual address to select the access-permission field for 4K pages.

The error has presumably not been noticed before because most guests don't
make use of the ability to set the access permissions differently for
each 1K subpage: if the guest gives the whole page the same access
permissions it doesn't matter which of the 4 AP fields we select.
(The whole issue is irrelevant for ARMv7 CPUs anyway because subpages
aren't supported there.)
Reported-by: NVivek Rai <Vivek.Rai@emulex.com>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 1392667690-8731-1-git-send-email-peter.maydell@linaro.org

The ethernet device in the musicpal only has two tx queues,
but we modelled it with four CTDP registers, presumably a
cut and paste from the rx queue registers. Since the tx_queue[]
array is only 2 entries long this allowed a guest to overrun
this buffer. Remove the nonexistent registers.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 1392737293-10073-1-git-send-email-peter.maydell@linaro.org
Acked-by: NJan Kiszka <jan.kiszka@web.de>
Cc: qemu-stable@nongnu.org

The Exynos4210 combiner has IIC_NIRQ inputs and IIC_NGRP outputs;
use the correct constant in the loop initializing our output
sysbus IRQs so that we don't overrun the output_irq[] array.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 1392659611-8439-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Cc: qemu-stable@nongnu.org

Correct some obviously nonsensical bit manipulation spotted by Coverity
when constructing the short-form PAR value for ATS operations.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 1392659525-8335-1-git-send-email-peter.maydell@linaro.org

The integrator's timer read/write functions log an error for
bad addresses in guest accesses, but were falling through and
using an out of bounds array index rather than returning early.
Fix this.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Message-id: 1392647854-8067-4-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org

Add a cast to avoid an unintended sign extension that
would mean we returned 0xffffffff in the high 32 bits
for an IA0 read if bit 31 in the MAC address was 1.
(This is harmless since we'll only be doing 4 byte
reads, but it could be confusing, so best avoided.)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Message-id: 1392647854-8067-3-git-send-email-peter.maydell@linaro.org

Fix incorrect use of sizeof() rather than ARRAY_SIZE() to guard
accesses into the mb_clock[] array, which was allowing a malicious
guest to overwrite the end of the array.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Message-id: 1392647854-8067-2-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org

This is now obsolete - remove the header and all its inclusions.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Inline the only usage of each of xilinx_axiethernet_init and
xilinx_axidma_init. Converts this init to at least a semi-recent QOM
styling.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Inline the only usage. Converts this init to at least a semi-recent QOM
styling.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Inline these usages. Converts these init to at least a semi-recent QOM
styling.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Inline these usages. Converts these init to at least a semi-recent QOM
styling.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Define (missing) macros for the interrupt and memory maps for the sake
of self documentation.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>