The current implementation of hot-unplug handler is abrupt. Any pci
operation will be just rejected if pci device is unconfigured. Thus a
pci device can not be reset or destroyed in a right, smooth and safe
way.

Improve this as follows:
- Notify the guest via a HP_EVENT_DECONFIGURE_REQUEST(0x303) event in
  the unplug handler, giving it a chance to deconfigure the device via
  sclp and allowing us to continue hot-unplug afterwards.
- Set up a timer that will generate the HP_EVENT_CONFIGURE_TO_STBRES
  (0x304) event as before if the guest did not react after an adequate
  time.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Present code uses fid as the part of message data of msix for looking
up the specific zpci device. However it limits the usable range of fid,
and the code looking up the zpci device may fail due to truncation of
the fid.

In addition, fh is composed of enabled bit, FH_VIRT and the array index.
So we can use the array index as the identifier to store in msg data.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Firstly the function misses dmaas checking. This patch adds it.

Secondly the function uses s390_pci_find_dev_by_fh() to look up the
zpci device. This may fail if the guest provides a valid and disabled
fh but fh of the associated zpci device is enabled. Thus we use
s390_pci_find_dev_by_idx() instead.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Because of the refactor of s390_pci_find_dev_by_idx(), list_pci()
should be updated. We introduce a new function to get the next
available zpci device. It simplifies the code of looking up zpci
devices.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

s390_find_dev_by_idx() only indexes usable zpci devices. It implies
that the index value of each zpci device is dynamic and may change if
a new zpci device is plugged. So we have to use a constant index to
look up the device.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The code in CLP_SET_PCI_FN case misses some checkings. Let's add
them.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

We need to support hot-plug/hot-unplug for the new zpci devices as
well. This patch enables the present hot-plug/hot-unplug handlers
to support not only generic pci devices but also zpci devices.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The uid-checking facility guarantees uniqueness of the uid within the
vm and exposes the real uid to the guest when listing pci devices.
Let's always enable it and present it to the guest in the response to
the list pci clp command.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

To support definitions of s390 pci attributes in Qemu cmdline, we have
to make current S390PCIBusDevice struct inherit DeviceState and add
three properties for it. Currently we only support definitions of uid
and fid.

'uid' is optionally defined by users, identifies a zpci device and
must be defined with a 16-bit and non-zero unique value.

'fid' ranges from 0x0 to 0xFFFFFFFF. For fid property, we introduce a
new PropertyInfo by the name of s390_pci_fid_propinfo with our special
setter and getter. As 'fid' is optional, introduce 'fid_defined' to
track whether the user specified a fid.

'target' field is to direct qemu to find the corresponding generic PCI
device. It is equal to the 'id' value of one of generic pci devices.
If the user doesn't specify 'id' parameter for a generic pci device,
its 'id' value will be generated automatically and use this value as
'target' to create an associated zpci device.

If the user did not specify 'uid' or 'fid', values are generated
automatically. 'target' is required.

In addition, if a pci device has no associated zpci device, the code
will generate a zpci device automatically for it.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Currently each zpci device holds its own DMA address space and memory
region. At the same time, all instances of zpci device are stored in
S390pciState. So duirng the initialization of S390pciState, all zpci
devices are created and then all DMA address spaces are created. Thus,
when initializing pci devices, their corresponding DMA address spaces
could be found.

But zpci qdev will be introduced later. Zpci device may be initialized
and plugged afterwards generic pci device. So we should initialize all
DMA address spaces and memory regions before initializing zpci devices.

We introduce a new struct named S390PCIIOMMU. And a new field of
S390pciState, which is an array to store all instances of S390PCIIOMMU,
is added so that qemu pci code could find the corresponding DMA
address space when initializing a generic pci device. And this should
be done before the connection of a zpci device and a generic pci
device is built.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

To enable S390PCIBusDevice as qdev, there should be a new bus to
plug and manage all instances of S390PCIBusDevice. Due to this,
S390PCIBus is introduced.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Current code uses some fields combinatorially to indicate the state of
a s390 pci device. This patch introduces device states in order to make
the code more readable and more logical.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Because this function is called very frequently, we should use a more
effective way to find the zpci device. So we use the FH's index to get
the device directly.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Present code uses some macros to structure PCI Function Handle. But
their names don't have a uniform format. Let's use FH_MASK_ as the
unified prefix.

While we're at it, differentiate the SHM bits: use different bits for
vfio and emulated devices.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

We forgot to write the fid; fix that.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

There are a number of places where the code needs to get the instance
of S390pciState. It calls object_resolve_path() every time. This
wastes a lot of time and leads to low performance. Thus we add
s390_get_phb() to improve it.

Because we always have a phb, we remove all return checkings in the
callers and add an assert in s390_get_phb() to make sure that phb is
getted successfully.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

In commit d78c19b5, vfio code stores
the IOMMU's offset_within_address_space and adjusts the IOVA before
calling vfio_dma_map/vfio_dma_unmap. But s390_translate_iommu already
considers the base address of an IOMMU memory region.

Thus we use pal as the size and 0x0 as the base address to initialize
IOMMU memory subregion.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The previous patch moved virtual css bridge and bus out from
virtio-ccw, but kept the direct reference of virtio-ccw specific
unplug function inside css-bridge.c.

To make the virtual css bus and bridge useful for non-virtio devices,
this introduces a common unplug function pointer "unplug" to call
specific virtio-ccw unplug parts. Thus, the tight coupling to
virtio-ccw can be removed.

This unplug pointer is a member of CCWDeviceClass, which is introduced
as an abstract device layer called "ccw-device". This layer is between
DeviceState and specific devices which are plugged in virtual css bus,
like virtio-ccw device. The specific unplug handlers should be assigned
to "unplug" during initialization.
Signed-off-by: NJing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NDong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Currently, common base layers virtual css bridge and bus are
defined in hw/s390x/virtio-ccw.c(h). In order to support
multiple types of devices in the virtual channel subsystem,
especially non virtio-ccw, refactoring work needs to be done.

This work is just a pure code move without any functional change
except dropping an empty function virtual_css_bridge_init() and
virtio_ccw_busdev_unplug() changing. virtio_ccw_busdev_unplug()
is specific to virtio-ccw but gets referenced from the common
virtual css bridge code. To keep the functional changes to a
minimum we export this function from virtio-ccw.c and continue
to reference it inside virtual_css_bridge_class_init()
(now living in hw/s390x/css-bridge.c). A follow-up patch will
clean this up.
Signed-off-by: NJing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NDong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Introduce a TYPE_* define (like we already use for a couple of other
QOM types) for the name of the virtual CSS bridge QOM type instead of
sprinkling the same string literal over several source files.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

A lot of what virtio_ccw_device_realize() does isn't specific to
virtio; it would apply to emulated CCW as well. Factor it out to make
it easier to implement emulated CCW devices later on.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NDong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: NHalil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

When migrating from a different QEMU version, the start_address and
bios_start_address may differ. During migration these values are migrated
and overwrite the values that were detected by QEMU itself.

On a reboot, QEMU will reload its own BIOS, but use the migrated start
addresses, which does not work if the values differ.

Fix this by not relying on the migrated values anymore, but still
provide them during migration, so existing QEMUs continue to work.
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

If bootindex is specified for a device, we need to IPL from
it. Currently it works for ccw devices, but not for SCSI. To be able to
IPL from the specific device, pc-bios needs to know its address.
For this reason we add special QEMU_SCSI IPL type into the IPLB
structure, that contains the scsi device address.

We enhance the ipl block with a currently qemu-only parameter block
that allows us to specify a concrete scsi device.
Signed-off-by: NAlexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: NEric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Use the new interface.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Move all trace-events for files in the hw/s390x/ directory to
their own file.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1466066426-16657-29-git-send-email-berrange@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

This patch simplifies code that uses a local_err variable just to
immediately use it for an error_propagate() call.

Coccinelle patch used to perform the changes added to
scripts/coccinelle/remove_local_err.cocci.
Reviewed-by: NEric Blake <eblake@redhat.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-3-git-send-email-ehabkost@redhat.com>
Reviewed-by: NMarkus Armbruster <armbru@redhat.com>
[Blank line in s390-virtio-ccw.c restored]
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>

error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.

Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: NEric Blake <eblake@redhat.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>

The sclp scp read info call fills in a buffer with information about the
system. With more than 248 CPUs we overflow the 4k buffer of the SCCB,
leading to random data corruption. Basically ALL guest operating systems
call scp read info, so let's limit the machines to 248 CPUs to make it
obvious that >=249 does not work.

As KVM also limits itself to 248 and TCG on s390 does not support
SMP, this should cause no regression for any user as no VMs with more
than 248 VCPUs were ever possible.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: NBoris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

This allows to trace changes in the summary and queue indicators
for the non-irqfd case. For irqfd, kernel traces are needed instead.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Let's introduce a CssDevId to handle device ids of the xx.x.xxxx
type used for channel devices. This has some benefits:

- We can use them in virtio-ccw and split the validity checks for
  a channel device id in general from the constraint checking
  within the virtio-ccw scope.
- We can reuse the device id type for future non-virtio channel
  devices.

While we're at it, improve the validity checks and disallow e.g.
trailing characters.
Suggested-by: NDong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: NDong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

According to the Principles of Operation (more precisely the subsection
'Channel-Report Word'), a subchannel put into the installed parameters
initialized state is in the same state as after an I/O system reset (just
parameters possibly changed). This implies that any I/O interrupts for that
subchannel are no longer pending (as I/O system resets clear I/O
interrupts). Therefore, we need an interface to clear pending I/O
interrupts. Make css_generate_sch_crws clear the pending IO interrupts for
the subchannel.
Signed-off-by: NHalil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Signed-off-by: NMichael Tokarev <mjt@tls.msk.ru>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The s390 skeys monitor command needs to write out a plain text
file. Currently it is using the QEMUFile class for this, but
work is ongoing to refactor QEMUFile and eliminate much code
related to it. The only feature qemu_fopen() gives over fopen()
is support for QEMU FD passing, but this can be achieved with
qemu_open() + fdopen() too. Switching to regular stdio FILE
APIs avoids the need to sprintf via an intermedia buffer which
slightly simplifies the code.
Reviewed-by: NEric Blake <eblake@redhat.com>
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>
Reviewed-by: NJuan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-2-git-send-email-berrange@redhat.com>
Signed-off-by: NAmit Shah <amit.shah@redhat.com>

Switch to adding compat properties incrementaly instead of
completly overwriting compat_props per machine type.
That removes data duplication which we have due to nested
[PC|SPAPR]_COMPAT_* macros.

It also allows to set default device properties from
default foo_machine_options() hook, which will be used
in following patch for putting VMGENID device as
a function if ISA bridge on pc/q35 machines.
Suggested-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NEduardo Habkost <ehabkost@redhat.com>
[ehabkost: Fixed CCW_COMPAT_* and PC_COMPAT_0_* defines]
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>

Move cpu_inject_* to the only C file where they are used.

Move ioinst.h declarations that need S390CPU to cpu.h, to make
ioinst.h independent of cpu.h.

Move channel declarations that only need SubchDev from cpu.h
to css.h, to make more channel users independent of cpu.h.
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The comment talks about a non-ELF object while the
example gives ELF object.
Signed-off-by: NMichael Tokarev <mjt@tls.msk.ru>

Fix indentation of PciCfgSccb struct.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The configure/deconfigure sclp commands need a SCCB with a length of
at least 16. Indicate in the response code if this is not fulfilled.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Enhance error handling for mpcifc_service_call() to propagate errors
to guest by setting status codes or triggering program interrupts.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

When deconfiguring a s390 pci device, we should deconfigure the
corresponding IOMMU memory region and the IRQs for the device.
Signed-off-by: NYi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: NPierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>