- 04 3月, 2016 2 次提交
-
-
由 Peter Maydell 提交于
If we're booting in Secure mode, provide a secure-only RAM (just 16MB) so that secure firmware has somewhere to run from that won't be accessible to the Non-secure guest. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Message-id: 1455288361-30117-2-git-send-email-peter.maydell@linaro.org
-
由 Peter Maydell 提交于
The virt board restricts guests to only 30GB of RAM. This is a hangover from the vexpress-a15 board, and there's no inherent reason for it. 30GB is smaller than you might reasonably want to provision a VM for on a beefy server machine. Raise the limit to 255GB. We choose 255GB because the available space we currently have below the 1TB boundary is up to the 512GB mark, but we don't want to paint ourselves into a corner by assigning it all to RAM. So we make half of it available for RAM, with the 256GB..512GB range available for future non-RAM expansion purposes. If we need to provide more RAM to VMs in the future then we need to: * allocate a second bank of RAM starting at 2TB and working up * fix the DT and ACPI table generation code in QEMU to correctly report two split lumps of RAM to the guest * fix KVM in the host kernel to allow guests with >40 bit address spaces The last of these is obviously the trickiest, but it seems reasonable to assume that anybody configuring a VM with a quarter of a terabyte of RAM will be doing it on a host with more than a terabyte of physical address space. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org> Tested-by: NWei Huang <wei@redhat.com> Message-id: 1456402182-11651-1-git-send-email-peter.maydell@linaro.org
-
- 26 2月, 2016 1 次提交
-
-
由 Andrew Baumann 提交于
Recent changes to sdhci broke SD on raspi. This change mirrors the logic to create the SD card device at the board level. Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Message-id: 1456351128-5560-1-git-send-email-Andrew.Baumann@microsoft.com Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 23 2月, 2016 1 次提交
-
-
由 Michael S. Tsirkin 提交于
While guest/host ABI is documented in hw/acpi/bios-linker-loader.c, the API was left undocumented. This adds documentation for all API functions. Additionally, input is validated to make sure all pointers fall within range of provided files. To allow this validation for checksum commands, bios_linker_loader_add_checksum is changed to accept GArray * in place of void *. Reported-by: NIgor Mammedov <imammedo@redhat.com> Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
-
- 20 2月, 2016 4 次提交
-
-
由 Eric Auger 提交于
qemu_fdt_setprop asserts in case of error hence no need to check the returned value. Signed-off-by: NEric Auger <eric.auger@linaro.org> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
-
由 Eric Auger 提交于
This patch allows the instantiation of the vfio-amd-xgbe device from the QEMU command line (-device vfio-amd-xgbe,host="<device>"). The guest is exposed with a device tree node that combines the description of both XGBE and PHY (representation supported from 4.2 onwards kernel): Documentation/devicetree/bindings/net/amd-xgbe.txt. There are 5 register regions, 6 interrupts including 4 optional edge-sensitive per-channel interrupts. Some property values are inherited from host device tree. Host device tree must feature a combined XGBE/PHY representation (>= 4.2 host kernel). 2 clock nodes (dma and ptp) also are created. It is checked those clocks are fixed on host side. AMD XGBE node creation function has a dependency on vfio Linux header and more generally node creation function for VFIO platform devices only make sense with CONFIG_LINUX so let's protect this code with #ifdef CONFIG_LINUX. Signed-off-by: NEric Auger <eric.auger@linaro.org> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
-
由 Eric Auger 提交于
Some passthrough'ed devices depend on clock nodes. Those need to be generated in the guest device tree. This patch introduces some helpers to build a clock node from information retrieved in the host device tree. - copy_properties_from_host copies properties from a host device tree node to a guest device tree node - fdt_build_clock_node builds a guest clock node and checks the host fellow clock is a fixed one. fdt_build_clock_node will become static as soon as it gets used. A dummy pre-declaration is needed for compilation of this patch. Signed-off-by: NEric Auger <eric.auger@linaro.org> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
-
由 Eric Auger 提交于
This patch aligns the prototype with qemu_fdt_getprop. The caller can choose whether the function self-asserts on error (passing &error_fatal as Error ** argument, corresponding to the legacy behavior), or behaves differently such as simply output a message. In this later case the caller can use the new lenp parameter to interpret the error if any. Signed-off-by: NEric Auger <eric.auger@linaro.org> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
-
- 18 2月, 2016 1 次提交
-
-
由 Peter Maydell 提交于
Move the creation of the SD card device from the sdhci_sysbus device itself into the boards that create these devices. This allows us to remove the cannot_instantiate_with_device_add notation because we no longer call drive_get_next in the device model. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Reviewed-by: NAlistair Francis <alistair.francis@xilinx.com> Message-id: 1455646193-13238-7-git-send-email-peter.maydell@linaro.org
-
- 16 2月, 2016 1 次提交
-
-
由 Peter Maydell 提交于
Clean up includes so that osdep.h is included first and headers which it implies are not included manually. This commit was created with scripts/clean-includes. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Reviewed-by: NEric Blake <eblake@redhat.com>
-
- 11 2月, 2016 2 次提交
-
-
由 Stephen Warren 提交于
Return a valid value from the BCM2835 property mailbox query "get board revision". This query is used by U-Boot. Implementing it fixes the first obvious difference between qemu and real HW. The value returned is currently hard-coded to match the RPi2 I own. Other values are legal, e.g. different board manufacturer field values are likely to exist in the wild. Cc: Andrew Baumann <Andrew.Baumann@microsoft.com> Signed-off-by: NStephen Warren <swarren@wwwdotorg.org> Reviewed-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Message-id: 1454993910-24077-1-git-send-email-swarren@wwwdotorg.org Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Andrew Jones 提交于
mach-virt doesn't yet support hotplug, but command lines specifying -smp <num>,maxcpus=<bigger-num> don't fail. Of course specifying bigger-num as something bigger than the machine supports, e.g. > 8 on a gicv2 machine, should fail though. This fix also makes mach- virt's max-cpus check truly consistent with the one in vl.c:main, as the one there was already correctly checking max-cpus instead of smp-cpus. Reported-by: NShannon Zhao <shannon.zhao@linaro.org> Signed-off-by: NAndrew Jones <drjones@redhat.com> Reviewed-by: NShannon Zhao <shannon.zhao@linaro.org> Message-id: 1454511578-24863-1-git-send-email-drjones@redhat.com Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 09 2月, 2016 1 次提交
-
-
由 Markus Armbruster 提交于
Done with the Coccinelle semantic patch from commit 007b0657, plus manual clean up of dead variables. Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Message-Id: <1452783732-6581-1-git-send-email-armbru@redhat.com> Reviewed-by: NEric Blake <eblake@redhat.com>
-
- 07 2月, 2016 2 次提交
-
-
由 Laszlo Ersek 提交于
Since build_rsdt() is implemented as common utility code (in "hw/acpi/aml-build.c"), it should expose -- and forward -- the oem_id and oem_table_id parameters between board code and the generic build_header() function. Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS) Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS) Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem) Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86) Cc: Richard W.M. Jones <rjones@redhat.com> Cc: Aleksei Kovura <alex3kov@zoho.com> Cc: Michael Tokarev <mjt@tls.msk.ru> Cc: Steven Newbury <steve@snewbury.org.uk> RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758 LP: https://bugs.launchpad.net/qemu/+bug/1533848Signed-off-by: NLaszlo Ersek <lersek@redhat.com> Reviewed-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Reviewed-by: NShannon Zhao <shannon.zhao@linaro.org>
-
由 Laszlo Ersek 提交于
This patch is the continuation of commit 8870ca0e ("acpi: support specified oem table id for build_header"). It will allow us to control the OEM ID field too in the SDT header. Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS) Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS) Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> (maintainer:NVDIMM) Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem) Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86) Cc: Richard W.M. Jones <rjones@redhat.com> Cc: Aleksei Kovura <alex3kov@zoho.com> Cc: Michael Tokarev <mjt@tls.msk.ru> Cc: Steven Newbury <steve@snewbury.org.uk> RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758 LP: https://bugs.launchpad.net/qemu/+bug/1533848Signed-off-by: NLaszlo Ersek <lersek@redhat.com> Reviewed-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: NMichael S. Tsirkin <mst@redhat.com> Reviewed-by: NShannon Zhao <shannon.zhao@linaro.org>
-
- 03 2月, 2016 7 次提交
-
-
由 Andrew Baumann 提交于
Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Andrew Baumann 提交于
The new version is slightly different, to support Rasbperry Pi (in particular, Pi1's arm11 core which doesn't support v7 instructions such as MOVW). Tested-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Andrew Baumann 提交于
This is the SoC for Raspberry Pi 2. Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Andrew Baumann 提交于
This device maintains all the non-CPU peripherals on bcm2835 (Pi1) which are also present on bcm2836 (Pi2). It also implements the private address spaces used for DMA and mailboxes. Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Igor Mammedov 提交于
in current impl. condition build_madt() { ... if (test_bit(i, cpuinfo->found_cpus)) is always true since loop handles only present CPUs in range [0..smp_cpus). But to fill usless cpuinfo->found_cpus we do unnecessary scan over QOM tree to find the same CPUs. So mark GICC as present always and drop not needed code that fills cpuinfo->found_cpus. Signed-off-by: NIgor Mammedov <imammedo@redhat.com> Reviewed-by: NShannon Zhao <shannon.zhao@linaro.org> Message-id: 1454323689-248759-1-git-send-email-imammedo@redhat.com Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Edgar E. Iglesias 提交于
When booting Linux on AArch64 enabled cores, setup EL1 and EL2 to use AArch64. Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Andrew Jones 提交于
This patch is the ACPI equivalent of "hw/arm/virt: Add always-on property to the virt board timer". The timer is always on, and thus setting this informs Linux that it may switch off the periodic timer. Switching off the periodic timer substantially reduces the number of interrupts the host needs to inject. Testing note: AArch64 guests (the only ones currently booting with ACPI) do not actually need this patch to determine it can turn the periodic timer off. I therefore used a hacked guest kernel to ensure this patch works as the equivalent DT patch does. Signed-off-by: NAndrew Jones <drjones@redhat.com> Reviewed-by: NShannon Zhao <shannon.zhao@linaro.org> Message-id: 1453380893-26174-1-git-send-email-drjones@redhat.com Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 21 1月, 2016 6 次提交
-
-
由 Christoffer Dall 提交于
The virt board has an arch timer, which is always on. Emit the "always-on" property to indicate to Linux that it can switch off the periodic timer and reduces the amount of interrupts injected into a guest. Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org> Reviewed-by: NAndrew Jones <drjones@redhat.com> Message-id: 1453204158-11412-1-git-send-email-christoffer.dall@linaro.org Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Peter Maydell 提交于
Add a secure memory region to the virt board, which is the same as the nonsecure memory region except that it also has a secure-only UART in it. This is only created if the board is started with the '-machine secure=on' property. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Acked-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
-
由 Peter Maydell 提交于
Wire up the system memory region to the CPUs explicitly by setting the QOM property. This doesn't change anything over letting it default, but will be needed for adding a secure memory region later. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com> Acked-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
-
由 Alistair Francis 提交于
Connect the sst25wf080 SPI flash to the EP108 board. Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> [PMM: free string when finished with it] Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Alistair Francis 提交于
Connect the Xilinx SPI devices to the ZynqMP model. Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> [ PC changes * Use QOM alias for bus connectivity on SoC level ] Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> [PMM: free the g_strdup_printf() string when finished with it] Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Alistair Francis 提交于
Move the ssi.h include file into the ssi directory. While touching the code also fix the typdef lines as checkpatch complains. Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 19 1月, 2016 1 次提交
-
-
由 Peter Maydell 提交于
Clean up includes so that osdep.h is included first and headers which it implies are not included manually. This commit was created with scripts/clean-includes. Signed-off-by: NPeter Maydell <peter.maydell@linaro.org> Message-id: 1449505425-32022-4-git-send-email-peter.maydell@linaro.org
-
- 15 1月, 2016 2 次提交
-
-
由 Shannon Zhao 提交于
When booting the VM with UEFI, UEFI takes ownership of the RTC hardware. While UEFI can use libfdt to disable the RTC device node in the DTB that it passes to the OS, it cannot modify AML. Therefore, we won't generate the RTC ACPI device at all when using UEFI. Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org> Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: NLaszlo Ersek <lersek@redhat.com> Reviewed-by: NAndrew Jones <drjones@redhat.com> Message-id: 1452867091-4023-1-git-send-email-shannon.zhao@linaro.org Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Alistair Francis 提交于
The Xilinx ZynqMP SoC and EP108 board supports three memory regions: - A 2GB region starting at 0 - A 32GB region starting at 32GB - A 256GB region starting at 768GB This patch adds support for the first two memory regions, which is automatically created based on the size specified by the QEMU memory command line argument. On hardware the physical memory region is one continuous region, it is then mapped into the three different regions by the DDRC. As we don't model the DDRC this is done at startup by QEMU. The board creates the memory region and then passes that memory region to the SoC. The SoC then maps the memory regions. Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com> Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com> Message-id: a1e47db941d65733724a300fcd98b74fbeeaaf22.1452637205.git.alistair.francis@xilinx.com Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 13 1月, 2016 7 次提交
-
-
由 Markus Armbruster 提交于
Commit 6daf194d, be62a2eb and 312fd5f2 got rid of a bunch, but they keep coming back. Tracked down with the Coccinelle semantic patch from commit 312fd5f2. Cc: Fam Zheng <famz@redhat.com> Cc: Peter Crosthwaite <crosthwaitepeter@gmail.com> Cc: Bharata B Rao <bharata@linux.vnet.ibm.com> Cc: Dominik Dingel <dingel@linux.vnet.ibm.com> Cc: David Hildenbrand <dahi@linux.vnet.ibm.com> Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com> Cc: Stefan Berger <stefanb@linux.vnet.ibm.com> Cc: Dr. David Alan Gilbert <dgilbert@redhat.com> Cc: Changchun Ouyang <changchun.ouyang@intel.com> Cc: zhanghailiang <zhang.zhanghailiang@huawei.com> Cc: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: NMarkus Armbruster <armbru@pond.sub.org> Reviewed-by: NDr. David Alan Gilbert <dgilbert@redhat.com> Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com> Acked-by: NBharata B Rao <bharata@linux.vnet.ibm.com> Acked-by: NFam Zheng <famz@redhat.com> Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Reviewed-by: NEric Blake <eblake@redhat.com> Message-Id: <1450452927-8346-17-git-send-email-armbru@redhat.com>
-
由 Markus Armbruster 提交于
Done with this Coccinelle semantic patch @@ expression FMT, E, S; expression list ARGS; @@ - error_report(FMT, ARGS, error_get_pretty(E)); + error_reportf_err(E, FMT/*@@@*/, ARGS); ( - error_free(E); | exit(S); | abort(); ) followed by a replace of '%s"/*@@@*/' by '"' and some line rewrapping, because I can't figure out how to make Coccinelle transform strings. We now use the error whole instead of just its message obtained with error_get_pretty(). This avoids suppressing its hint (see commit 50b7b000), but I can't see how the errors touched in this commit could come with hints. Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Message-Id: <1450452927-8346-12-git-send-email-armbru@redhat.com> Reviewed-by: NEric Blake <eblake@redhat.com>
-
由 Markus Armbruster 提交于
Same Coccinelle semantic patch as in commit 565f65d2. We now use the original error whole instead of just its message obtained with error_get_pretty(). This avoids suppressing its hint (see commit 50b7b000), but I don't think the errors touched in this commit can come with hints. Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Reviewed-by: NEric Blake <eblake@redhat.com> Message-Id: <1450452927-8346-3-git-send-email-armbru@redhat.com>
-
由 Markus Armbruster 提交于
virt_set_gic_version() calls exit(1) when passed an invalid property value. Property setters are not supposed to do that. Screwed up in commit b92ad394. Harmless, because the property belongs to a machine. Set an error object instead. Cc: Peter Maydell <peter.maydell@linaro.org> Cc: qemu-arm@nongnu.org Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Markus Armbruster 提交于
Printing CPU registers is not helpful during machine initialization. Moreover, these are straightforward configuration or "can get resources" errors, so dumping core isn't appropriate either. Replace hw_error() by error_report(); exit(1). Matches how we report these errors in other machine initializations. Cc: Richard Henderson <rth@twiddle.net> Cc: qemu-arm@nongnu.org Cc: qemu-ppc@nongnu.org Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by: NMarkus Armbruster <armbru@pond.sub.org> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> Reviewed-by: NThomas Huth <thuth@redhat.com> Message-Id: <1450370121-5768-2-git-send-email-armbru@redhat.com> Reviewed-by: NRichard Henderson <rth@twiddle.net>
-
由 Markus Armbruster 提交于
Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Message-Id: <1449764955-10741-3-git-send-email-armbru@redhat.com> Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
-
由 Markus Armbruster 提交于
Done with this Coccinelle semantic patch: @@ type T; identifier FUN, RET; expression list ARGS; expression ERR, EC; @@ ( - T RET = FUN(ARGS, &ERR); + T RET = FUN(ARGS, &error_fatal); | - RET = FUN(ARGS, &ERR); + RET = FUN(ARGS, &error_fatal); | - FUN(ARGS, &ERR); + FUN(ARGS, &error_fatal); ) - if (ERR != NULL) { - error_report_err(ERR); - exit(EC); - } This is actually a more elegant version of my initial semantic patch by courtesy of Eduardo. It leaves dead Error * variables behind, cleaned up manually. Cc: qemu-arm@nongnu.org Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Eduardo Habkost <ehabkost@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: NMarkus Armbruster <armbru@redhat.com> Reviewed-by: NEduardo Habkost <ehabkost@redhat.com>
-
- 12 1月, 2016 1 次提交
-
-
由 Ashok Kumar 提交于
Support the legacy -nic syntax for creating PCI network devices as well as the new-style -device options. This makes life easier for people moving from x86 KVM virtualization to ARM KVM virtualization and expecting their network configuration options to work the same way for both setups. We use "virtio" as the default NIC model if the user doesn't specify one. Signed-off-by: NAshok Kumar <ashoks@broadcom.com> Message-id: 1452091659-17698-1-git-send-email-ashoks@broadcom.com Reviewed-by: NPeter Maydell <peter.maydell@linaro.org> [PMM: expanded and clarified commit message] Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
-
- 23 12月, 2015 1 次提交
-
-
由 Igor Mammedov 提交于
Signed-off-by: NIgor Mammedov <imammedo@redhat.com> Reviewed-by: NMichael S. Tsirkin <mst@redhat.com> Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
-