Skip to content

Q
qemu

openeuler / qemu

通知 10
Star 0
Fork 0
Q
qemu

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 08 1月, 2016 10 次提交
  3. 07 1月, 2016 12 次提交
  5. 05 1月, 2016 5 次提交
    • G
      seabios: update binaries to release 1.9.0 · 4b9294c0
      由 Gerd Hoffmann 提交于 
      Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      4b9294c0
    • G
      seabios: stop updating aml files · bf864863
      由 Gerd Hoffmann 提交于 
      ACPI aml files traditionally have been managed in the seabios repo.
In qemu version 2.0 we've switched over to have qemu generate the
acpi tables and provide them to the firmware via fw_cfg.

The old aml files are still there and used for old machine types.
Well, actually the q35 file only, the piix4 version is compiled into
seabios (unless built with CONFIG_ACPI_DSDT=n) and is there for
reference only.

The aml files havn't been touched for a long time, and given that
new features requiring acpi changes are typically only added to new
machine types this is unlikely to change in the future.  So stop
updating them.

That allows to cleanup things a bit on the seabios side in the future.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      bf864863
    • G
      seabios: update 128k bios config · cae7e84e
      由 Gerd Hoffmann 提交于 
      Turn off OHCI + TPM support to keep the size below 128k.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      cae7e84e
    • G
      seabios: use new EXTRAVERSION to tag qemu builds · 437b8d8c
      由 Gerd Hoffmann 提交于 
      Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      437b8d8c
    • G
      seabios: update submodule to release 1.9.0 · ad30c0b0
      由 Gerd Hoffmann 提交于 
      Highlights / user visible changes in seabios:
 * boot menu key is ESC now.
 * virtio 1.0 support.
 * sdcard support.
 * fw_cfg dma suport.
 * usual share of bugfixes ;)

In vgabios:
 * Emulates leal instruction.  Works around a bug in old x86emu versions,
   which makes old xorg vesa drivers work (RHEL-5 for example).

full shortlog rel-1.8.2..rel-1.9.0
----------------------------------

Ameya Palande (1):
      x86: add barrier to read{b,w,l} and write{b,w,l} functions

Andreas Färber (1):
      checkrom: Fix typo in error message

Chen Fan (1):
      pci: enable SERR# for error forwarding in bridge control register

Gerd Hoffmann (28):
      vga: simplify vga builds
      vga: rework virtio-vga support
      vga: add virtio-vga to kconfig
      pci: allow to loop over capabilities
      virtio: run drivers in 32bit mode
      virtio: add struct vp_device
      virtio: pass struct pci_device to vp_init_simple
      virtio: add version 1.0 structs and #defines
      virtio: add version 0.9.5 struct
      virtio: find version 1.0 virtio capabilities
      virtio: create vp_cap struct for legacy bar
      virtio: add read/write functions and macros
      virtio: make features 64bit, support version 1.0 features
      virtio: add version 1.0 support to vp_{get,set}_status
      virtio: add version 1.0 support to vp_get_isr
      virtio: add version 1.0 support to vp_reset
      virtio: add version 1.0 support to vp_notify
      virtio: remove unused vp_del_vq
      virtio: add version 1.0 support to vp_find_vq
      virtio-scsi: fix initialization for version 1.0
      virtio-blk: fix initialization for version 1.0
      virtio: use version 1.0 if available (flip the big switch)
      virtio: also probe version 1.0 pci ids
      virtio: legacy cleanup
      virtio-blk: 32bit cleanup
      virtio-scsi: 32bit cleanup
      virtio-ring: 32bit cleanup
      virtio-pci: use high memory for rings

Julius Werner (1):
      xhci: Count new Max Scratchpad Bufs bits from XHCI 1.1

Kevin O'Connor (126):
      docs: add page for SeaVGABIOS
      docs: Add page describing the patch contribution process
      docs: Add page on available CBFS/fw_cfg runtime config files
      docs: Prefer triple backticks to multiple lines with single backticks
      smp: Fix smp race introduced in 0673b787
      docs: Note release date of 1.8.1
      vgabios: On bda_save_restore() the saved vbe_mode also has flags in it
      vgabios: Don't use extra stack if it appears a modern OS is in use
      docs: Clarify that pci-optionrom-exec doesn't apply to roms in cbfs
      checkstack: Replace function information tuple with class
      checkstack: Simplify yield calculations
      checkstack: Prefer passing "function" class instead of function address
      smbios: Use integer signature instead of string signature
      vgabios: Don't use "smsww" instruction - it confuses x86emu
      vgabios: Add config option for assembler fixups
      vgabios: Emulate "leal" instruction
      checkstack: Minor - continue if not a regular asm line
      Don't forward declare functions with "inline" in headers
      build: Support "make VERSION=xyz" to override the default build version
      tcg: Use seabios setup()/prepboot() calling convention for tcg
      build: CONFIG_VGA_FIXUP_ASM should depend on CONFIG_BUILD_VGABIOS
      bootorder: Update "extra pci root" buses bootorder format to match qemu
      Make sure all code checks for malloc failures
      docs: Note release date of 1.8.2
      block: Split process_op() command dispatch up into multiple functions
      block: Introduce default_process_op() with common command handling codes
      block: Route scsi style commands through 'struct disk_op_s'
      blockcmd: Introduce scsi_fill_cmd()
      ata: Handle ATA ATAPI drives directly via 'struct disk_op_s' requests
      ahci: Handle AHCI ATAPI drives directly via 'struct disk_op_s' requests
      usb-msc: Handle USB drives directly via 'struct disk_op_s' requests
      usb-uas: Handle USB drives directly via 'struct disk_op_s' requests
      lsi-scsi: Handle LSI drives directly via 'struct disk_op_s' requests
      esp-scsi: Handle ESP drives directly via 'struct disk_op_s' requests
      megasas: Handle Megasas drives directly via 'struct disk_op_s' requests
      virtio-scsi: Handle virtio drives directly via 'struct disk_op_s' requests
      pvscsi: Move pvscsi_fill_req() code into pvscsi_cmd()
      pvscsi: Handle pvscsi drives directly via 'struct disk_op_s' requests
      blockcmd: Remove unused scsi_process_op() and cdb_cmd_data()
      blockcmd: Convert cdb_is_read() to scsi_is_read()
      block: Rename process_XXX_op() functions to XXX_process_op()
      coreboot: Try to auto-detect if the CBFS anchor pointer is a relative pointer
      ps2: Support mode for polling the PS2 port instead of using irqs
      ata: Make sure "chanid" is relative to PCI device for bootorder file
      Don't enable interrupts prior to IVT and PIC setup
      ps2: Don't wait 100ms to discard possible extra reset receive byte
      timer: Delay timestamp counter init until after pmtimer is probed
      timer: Add CONFIG_TSC_TIMER build option to disable the CPU TSC timer
      ramdisk: Allow ramdisk support (CONFIG_FLASH_FLOPPY) under QEMU
      Minor - move declaration of CDRom_locks to code that uses it
      smm: ignore bits 16,18-31 of SMM revision ID at runtime too
      vgafb: Minor - move gfx_common() variables outside of switch statement
      sdcard: Check if card is present before sending commands to card
      sdcard: Implement controller frequency setting according to sdhci spec
      sdcard: Make sure controller support 3.3V before enabling it
      sdcard: Set timeout control register during init (to max allowed timeout)
      sdcard: Improve SD card initialization command sequence
      sdcard: Add proper delays during card power up
      mptable: Don't create mptable if it is very large
      optionroms: Don't run option rom on PCI bar if CBFS/fw_cfg version exists
      edd: Pass the segment/offset from int 1348 calls using a 'struct segoff_s'
      edd: Reduce parameters to fill_generic_edd()
      Move CanInterrupt check to check_irqs()
      Call cpu_relax() if yielding prior to interrupts being enabled
      sdcard: Fix typo - use sdcard_pio() instead of sdcard_pio_app()
      sdcard: Fill command bits according to spec
      sdcard: Support SDHCI v3.00 spec clock setting
      sdcard: Move power setup to new function sdcard_set_power()
      sdcard: Power controller up to maximum voltage supported
      sdcard: Power down controller on failure
      sdcard: The card should never be in a busy state at start of sdcard_pio()
      sdcard: Implement timeout on every block read in sdcard_pio_transfer()
      sdcard: Rename waitw() to sdcard_waitw() and simplify
      sdcard: Perform a controller reset at start of init
      sdcard: Check for error events during sdcard_pio()
      sdcard: Initial support for MMC cards
      sdcard: Allow the sdcard driver to run on real hardware
      rtc: Support disabling the RTC timer irq support
      Add minimal support for machines without hardware interrupts
      ps2: Eliminate "etc/ps2-poll-only"; use CONFIG_HARDWARE_IRQ instead
      sdcard: Allow sdcard addresses to be specified in CBFS files
      xhci: Minor - add USB port type comments to xhci_hub_reset()
      docs: Don't use an add-symbol-file offset when describing gdb debugging
      rtc: Disable NMI in rtc_mask()
      sdcard: Move sdcard_set_frequency()/sdcard_set_power() in sdcard.c
      sdcard: Move frequency setting into sdcard_card_setup()
      sdcard: Move drive registration to sdcard_card_setup()
      sdcard: Turn card_type into a bitmap and store if card is MMC type
      sdcard: Display sdcard product name in boot menu
      sdcard: Obtain card capacity and report it on the boot menu
      megasas: Use outl() on MFI_IDB register
      minor - correct spelling error in comment
      Simplify transition16/32 assembler code
      docs: Minor - add "code relocation" link to "Execution and code flow" document
      Unify smm/sloppy variants of call32_prep/post and call16_helper
      Rename Call32Data to Call16Data
      Unify inline assembler in variants of call16 functions
      Unify call32_sloppy() and call32()
      Use transition32_nmi_off from call32() and call16_back()
      Consolidate code16*() functions
      Always enable caching on transition32; backup/restore cr0 on call32
      e820: Introduce e820_remove() and avoid exporting E820_HOLE
      e820: Rename memmap.c to e820map.c and use consistent "e820_" prefix
      e820: Update debugging messages to report 64bit values
      virtio: Simplify vring alignment code
      virtio: Move standard definitions from virtio-ring.h to standard headers
      malloc: Use consistent naming for internal low-level "alloc" functions
      malloc: Introduce common helper alloc_new_detail()
      malloc: Add warning if free() called on invalid memory
      malloc: Don't mix virtual and physical addresses
      memmap: Introduce SYMBOL() macro to access linker script symbols
      build: Rework version generation; don't allow make version override
      build: Report gcc and binutils versions in debug log
      build: Generate "reproducible" version strings on "clean" builds
      stacks: Use macro wrappers for call32() and stack_hop_back()
      malloc: Rename csm_malloc_preinit() to malloc_csm_preinit()
      build: Be more permissive in buildversion.py tool version scan
      docs: Document 'make EXTRAVERSION=xyz' and scripts/tarball.sh
      build: Allow official tarball builds to be considered "clean"
      coreboot: Minor - avoid K&R style function declaration
      biostables: Minor - fix incorrect indentation
      virtio: Minor - replace tab characters with space
      docs: Minor - replace seavgabios text in Build_overview.md with link
      buildversion: Avoid subprocess.check_output() as that requires python2.7
      buildversion: Add debugging messages
      docs: Note v1.9.0 release

Kyösti Mälkki (1):
      PCI SDHCI driver: Fix base address

Magnus Granberg (1):
      build: use -fstack-check=no when available

Marc Marí (1):
      Add QEMU fw_cfg DMA interface

Marcel Apfelbaum (2):
      fw/pci: scan all buses if extraroots romfile is present
      fw/pci: map memory and IO regions for multiple pci root buses

Paolo Bonzini (4):
      boot.c: delay exiting boot if menu key is ESC
      boot: switch default menu key to ESC
      smm: ignore bits 16,18-31 of SMM revision ID
      smm: fix outl argument order

Paulo Alcantara (1):
      ich9: initialise RCBA register through LPC interface

Quan Xu (1):
      make SeaBios compatible with Xen vTPM.

Stefan Berger (9):
      Add an implementation of a TPM TIS driver
      Implementation of the TCG BIOS extensions
      Support for BIOS interrupt handler
      Add 'measurement' code to the BIOS
      tpm: Introduce a #define for command tag
      tpm: Be consistent with array sizes in tcgbios.c
      tpm: clean up parameters to build_and_send_cmd
      tpm: Clean up in tcgbios.h
      tpm: Move call to tpm_option_rom into init_optionrom

Stefan Weil (2):
      megasas: Fix outw, outl argument order
      Fix typos found by codespell

Vladimir Serbinenko (3):
      ahci: Ignore max_ports.
      Link rom.o with -N option.
      Add multiboot support.

tpearson@raptorengineeringinc.com (1):
      Add an option to only execute option ROMs contained in CBFS
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      ad30c0b0
  7. 23 12月, 2015 13 次提交