Move qemu_gluster_close() further up in the file, in preparation
for the next patch, to avoid a forward declaration.
Signed-off-by: NJeff Cody <jcody@redhat.com>

Upon error, gluster will call the aio callback function with a
ret value of -1, with errno set to the proper error value.  If
we set the acb->ret value to the return value in the callback,
that results in every error being EPERM (i.e. 1).  Instead, set
it to the proper error result.
Reviewed-by: NNiels de Vos <ndevos@redhat.com>
Signed-off-by: NJeff Cody <jcody@redhat.com>

fw_cfg: Adopt /opt/RFQDN convention

# gpg: Signature made Tue 19 Apr 2016 15:14:20 BST using RSA key ID EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg:                 aka "Markus Armbruster <armbru@pond.sub.org>"

* remotes/armbru/tags/pull-fw_cfg-2016-04-19:
  fw_cfg: Adopt /opt/RFQDN convention
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

FW CFG's primary user is QEMU, which uses it to expose configuration
information (in the widest sense) to Firmware.  Thus the name FW CFG.

FW CFG can also be used by others for their own purposes.  QEMU is
merely acting as transport then.  Names starting with opt/ are
reserved for such uses.  There is no provision, however, to guide safe
sharing among different such users.

Fix that, loosely following QMP precedence: names should start with
opt/RFQDN/, where RFQDN is a reverse fully qualified domain name you
control.

Based on a more ambitious patch from Michael Tsirkin.

Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NGabriel Somlo <somlo@cmu.edu>
Reviewed-by: NLaszlo Ersek <lersek@redhat.com>

ehci: fix (s)iTD looping issue (CVE-2015-8558) in a different way.

# gpg: Signature made Tue 19 Apr 2016 07:22:22 BST using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg:                 aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg:                 aka "Gerd Hoffmann (private) <kraxel@gmail.com>"

* remotes/kraxel/tags/pull-usb-20160419-1:
  Revert "ehci: make idt processing more robust"
  ehci: apply limit to iTD/sidt descriptors
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

ppc patch queueu for 2016-04-19

A single fix for a regression since 2.5.  This should be the last ppc
pull request for 2.6.

# gpg: Signature made Tue 19 Apr 2016 02:48:30 BST using RSA key ID 20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg:                 aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg:                 aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E  87DC 6C38 CACA 20D9 B392

* remotes/dgibson/tags/ppc-for-2.6-20160419:
  cuda: fix off-by-one error in SET_TIME command
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

cadence_uart_init() initializes an I/O memory region of size 0x1000
bytes.  However in uart_write(), the 'offset' parameter (offset within
region) is divided by 4 and then used to index the array 'r' of size
CADENCE_UART_R_MAX which is much smaller: (0x48/4).  If 'offset>>=2'
exceeds CADENCE_UART_R_MAX, this will cause an out-of-bounds memory
write where the offset and the value are controlled by guest.

This will corrupt QEMU memory, in most situations this causes the vm to
crash.

Fix by checking the offset against the array size.

Cc: qemu-stable@nongnu.org
Reported-by: N李强 <liqiang6-s@360.cn>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NAlistair Francis <alistair.francis@xilinx.com>
Message-id: 20160418100735.GA517@redhat.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

X86 fix for 2.6.0-rc3

# gpg: Signature made Mon 18 Apr 2016 20:02:15 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"

* remotes/ehabkost/tags/x86-pull-request:
  target-i386: Set AMD alias bits after filtering CPUID data
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

This reverts commit 156a2e4d.

Breaks FreeBSD.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Commit "156a2e4d ehci: make idt processing more robust" tries to avoid a
DoS by the guest (create a circular iTD queue and let qemu ehci
emulation run in circles forever).  Unfortunately this has two problems:
First it misses the case of siTDs, and second it reportedly breaks
FreeBSD.

So lets go for a different approach: just count the number of iTDs and
siTDs we have seen per frame and apply a limit.  That should really
catch all cases now.
Reported-by: N杜少博 <dushaobo@360.cn>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

With the new framework the cuda_cmd_set_time command directly receive
the data, without the command byte. Therefore the time is stored at
in_data[0], not at in_data[1].

This fixes the "hwclock --systohc" command in a guest.

Cc: Hervé Poussineau <hpoussin@reactos.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Reviewed-by: NHervé Poussineau <hpoussin@reactos.org>
[this fixes a regression introduced by e6473178 "cuda: port SET_TIME
 command to new framework"]
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

QEMU complains about -cpu host on an AMD machine:
  warning: host doesn't support requested feature: CPUID.80000001H:EDX [bit 0]
For bits 0,1,3,4,5,6,7,8,9,12,13,14,15,16,17,23,24.

KVM_GET_SUPPORTED_CPUID and and x86_cpu_get_migratable_flags()
don't handle the AMD CPUID aliases bits, making
x86_cpu_filter_features() print warnings and clear those CPUID
bits incorrectly.

To avoid hacking x86_cpu_get_migratable_flags() to handle
CPUID_EXT2_AMD_ALIASES (just like the existing hack inside
kvm_arch_get_supported_cpuid()), simply move the
CPUID_EXT2_AMD_ALIASES code in x86_cpu_realizefn() after the
x86_cpu_filter_features() call.

This will probably make the CPUID_EXT2_AMD_ALIASES hack in
kvm_arch_get_supported_cpuid() unnecessary, too. The hack will be
removed in a follow-up patch after v2.6.0.
Reported-by: NRadim Krčmář <rkrcmar@redhat.com>
Tested-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NEduardo Habkost <ehabkost@redhat.com>

QOM CPUState and X86CPU

* MAINTAINERS cleanup

# gpg: Signature made Mon 18 Apr 2016 17:23:16 BST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg:                 aka "Andreas Färber <afaerber@suse.com>"

* remotes/afaerber/tags/qom-cpu-for-peter:
  MAINTAINERS: Drop target-i386 from CPU subsystem
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

X86CPU QOM type is in good hands and actively maintained these days, so
drop it from the generic QOM CPU subsystem.

Some refactorings and design questions will still intersect, but review
and discussions of individual series can still take place while opting out
of general X86CPU patch review.
Acked-by: NEduardo Habkost <ehabkost@redhat.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Update OpenBIOS images

# gpg: Signature made Mon 18 Apr 2016 09:39:31 BST using RSA key ID AE0F321F
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>"

* remotes/mcayland/tags/qemu-openbios-signed:
  Update OpenBIOS images
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

ppc patch queue for 2-16-04-18

Three bugfixe patches for 2.6 here.
* Two for bad implementation of some of the strong load/store
  instructions

* One for bad migration of the XER register.  This is a regression
  from 2.5, cause by a change in the way we represent at XER during
  runtime.

# gpg: Signature made Mon 18 Apr 2016 06:17:03 BST using RSA key ID 20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg:                 aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg:                 aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E  87DC 6C38 CACA 20D9 B392

* remotes/dgibson/tags/ppc-for-2.6-20160418:
  ppc: Fix migration of the XER register
  ppc: Fix the bad exception NIP value and the range check in LSWX
  ppc: Fix the range check in the LSWI instruction
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

seccomp branch queue

# gpg: Signature made Sat 16 Apr 2016 19:58:46 BST using RSA key ID 12F8BD2F
# gpg: Good signature from "Eduardo Otubo (Software Engineer @ ProfitBricks) <eduardo.otubo@profitbricks.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1C96 46B6 E1D1 C38A F2EC  3FDE FD0C FF5B 12F8 BD2F

* remotes/otubo/tags/pull-seccomp-20160416:
  seccomp: adding sysinfo system call to whitelist
  seccomp: Whitelist cacheflush since 2.2.0 not 2.2.3
  configure: Enable seccomp sandbox for MIPS
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

wxx patch queue

# gpg: Signature made Fri 15 Apr 2016 18:36:41 BST using RSA key ID 677450AD
# gpg: Good signature from "Stefan Weil <sw@weilnetz.de>"
# gpg:                 aka "Stefan Weil <stefan.weil@weilnetz.de>"
# gpg:                 aka "Stefan Weil <stefan.weil@bib.uni-mannheim.de>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 4923 6FEA 75C9 5D69 8EC2  B78A E08C 21D5 6774 50AD

* remotes/weil/tags/pull-wxx-20160415:
  wxx: Fix broken TCP networking (regression)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Update OpenBIOS images to SVN r1395 built from submodule.
Signed-off-by: NMark Cave-Ayland <mark.cave-ayland@ilande.co.uk>

env->xer only holds the lower bits of the XER register nowadays, the
SO, OV and CA bits are stored in separate variables (see the function
cpu_write_xer() for details). Since the migration code currently only
reads the "xer" variable, the upper bits are lost during migration.
Fix it by using cpu_read_xer() instead.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

The range checks in the LSWX instruction are completely insufficient:
They do not take the wrap-around case into account, and the check
"reg < rx" should be "reg <= rx" instead. Fix it by using the new
lsw_reg_in_range() helper function that is already used for LSWI, too.

Then there is a second problem: In case the INVAL exception is generated,
the NIP value is wrong, it currently points to the instruction before
the LSWX instruction. This is because gen_lswx() already decreases the
NIP value by 4 (to be prepared for page fault exceptions), and
powerpc_excp() later decreases it again by 4 while handling the program
exception. So to get this right, we've got to undo the "- 4" from
gen_lswx() here before calling helper_raise_exception_err().
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

There are two issues: First, the number of registers that are used has
to be calculated with "(nb + 3) / 4" (i.e. round always up, not down).
Second, the "start <= ra && (start + nr - 32) > ra" condition for the
wrap-around case is wrong: It has to be tested with "||" instead of "&&".
Since we can reuse this check later for the LSWX instruction, let's
place the fixed code into a helper function, too.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

Newer version of nss-softokn libraries (> 3.16.2.3) use sysinfo call
so qemu using rbd image hang after start when run in sandbox mode.

To allow using rbd images in sandbox mode we have to whitelist it.
Signed-off-by: NMiroslav Rezanina <mrezanin@redhat.com>
Acked-by: NEduardo Otubo <eduardo.otubo@profitbricks.com>

The cacheflush system call (found on MIPS and ARM) has been included in
the libseccomp header since 2.2.0, so include it back to that version.
Previously it was only enabled since 2.2.3 since that is when it was
enabled properly for ARM.

This will allow seccomp support to be enabled for MIPS back to
libseccomp 2.2.0.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-By: NAndrew Jones <drjones@redhat.com>
Acked-by: NEduardo Otubo <eduardo.otubo@profitbricks.com>

Enable seccomp on MIPS since libseccomp version 2.2.0 when MIPS support
was first added.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Acked-by: NEduardo Otubo <eduardo.otubo@profitbricks.com>

It is broken since commit c6196440.
Reported-by: NMichael Fritscher <michael@fritscher.net>
Tested-by: NMichael Fritscher <michael@fritscher.net>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NDaniel P. Berrange <berrange@redhat.com>
Signed-off-by: NStefan Weil <sw@weilnetz.de>

Block layer patches for 2.6.0-rc3

# gpg: Signature made Fri 15 Apr 2016 17:02:23 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"

* remotes/kevin/tags/for-upstream:
  nbd: Don't kill server on client that doesn't request TLS
  nbd: fix assert() on qemu-nbd stop
  nbd: Don't fail handshake on NBD_OPT_LIST descriptions
  qemu-iotests: 041: More robust assertion on quorum node
  qemu-iotests: place valgrind log file in scratch dir
  qemu-iotests: tests: do not set unused tmp variable
  qemu-iotests: common.rc: drop unused _do()
  qemu-iotests: drop unused _within_tolerance() filter
  Fix pflash migration
  block: Don't ignore flags in blk_{,co,aio}_write_zeroes()
  block/vpc: update comments to be compliant w/coding guidelines
  block/vpc: set errp in vpc_open
  block/vpc: make checks on max table size a bit more lax
  block/vpc: Use the correct max sector count for VHD images
  block/vpc: use current_size field for XenConverter VHD images
  vpc: use current_size field for XenServer VHD images
  block/vpc: set errp in vpc_create
  block: Fix blk_aio_write_zeroes()
  qemu-io: Support 'aio_write -z'
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

hostmem-file: plug a small leak

# gpg: Signature made Fri 15 Apr 2016 17:30:42 BST using RSA key ID EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg:                 aka "Markus Armbruster <armbru@pond.sub.org>"

* remotes/armbru/tags/pull-backends-2016-04-15:
  hostmem-file: plug a small leak
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Block patches for 2.6.0-rc3.

# gpg: Signature made Fri Apr 15 17:57:30 2016 CEST using RSA key ID E838ACAD
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"

* mreitz/tags/pull-block-for-kevin-2016-04-15:
  nbd: Don't kill server on client that doesn't request TLS
  nbd: fix assert() on qemu-nbd stop
  nbd: Don't fail handshake on NBD_OPT_LIST descriptions
  qemu-iotests: 041: More robust assertion on quorum node
  qemu-iotests: place valgrind log file in scratch dir
  qemu-iotests: tests: do not set unused tmp variable
  qemu-iotests: common.rc: drop unused _do()
  qemu-iotests: drop unused _within_tolerance() filter
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

Upstream NBD documents (as of commit 4feebc95) that servers MAY
choose to operate in a conditional mode, where it is up to the
client whether to use TLS.  For qemu's case, we want to always be
in FORCEDTLS mode, because of the risk of man-in-the-middle
attacks, and since we never export more than one device; likewise,
the qemu client will ALWAYS send NBD_OPT_STARTTLS as its first
option.  But now that SELECTIVETLS servers exist, it is feasible
to encounter a (non-qemu) client that is programmed to talk to
such a server, and does not do NBD_OPT_STARTTLS first, but rather
wants to probe if it can use a non-encrypted export.

The NBD protocol documents that we should let such a client
continue trying, on the grounds that maybe the client will get the
hint to send NBD_OPT_STARTTLS, rather than immediately dropping
the connection.

Note that NBD_OPT_EXPORT_NAME is a special case: since it is the
only option request that can't have an error return, we have to
(continue to) drop the connection on that one; rather, what we are
fixing here is that all other replies prior to TLS initiation tell
the client NBD_REP_ERR_TLS_REQD, but keep the connection alive.
Signed-off-by: NEric Blake <eblake@redhat.com>
Message-id: 1460671343-18485-1-git-send-email-eblake@redhat.com
Signed-off-by: NMax Reitz <mreitz@redhat.com>

From time to time qemu-nbd is crashing on the following assert:
    assert(state == TERMINATING);
    nbd_export_closed
    nbd_export_put
    main
and the state at the moment of the crash is evaluated to TERMINATE.

During shutdown process of the client the nbd_client_thread thread sends
SIGTERM signal and the main thread calls the nbd_client_closed callback.
If the SIGTERM callback will be executed after change the state to
TERMINATING, then the state will once again be TERMINATE.

To solve the issue, we must change the state to TERMINATE only if the state
is RUNNING. In the other case we are shutting down already.
Signed-off-by: NPavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: NDenis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1460629215-11567-1-git-send-email-den@openvz.org
Signed-off-by: NMax Reitz <mreitz@redhat.com>

The NBD Protocol states that NBD_REP_SERVER may set
'length > sizeof(namelen) + namelen'; in which case the rest
of the packet is a UTF-8 description of the export.  While we
don't know of any NBD servers that send this description yet,
we had better consume the data so we don't choke when we start
to talk to such a server.

Also, a (buggy/malicious) server that replies with length <
sizeof(namelen) would cause us to block waiting for bytes that
the server is not sending, and one that replies with super-huge
lengths could cause us to temporarily allocate up to 4G memory.
Sanity check things before blindly reading incorrectly.
Signed-off-by: NEric Blake <eblake@redhat.com>
Message-id: 1460077777-31004-1-git-send-email-eblake@redhat.com
Reviewed-by: NAlex Bligh <alex@alex.org.uk>
Signed-off-by: NMax Reitz <mreitz@redhat.com>

Block nodes are now assigned names automatically, therefore the test
case is fragile in using fixed indices in result. Introduce a method in
iotests.py and do the matching more sensibly.
Signed-off-by: NFam Zheng <famz@redhat.com>
Message-id: 1460518995-1338-1-git-send-email-famz@redhat.com
Signed-off-by: NMax Reitz <mreitz@redhat.com>

Do not place the valgrind log file at a predictable path in a
world-writable location. Use the common scratch directory (${TEST_DIR})
instead.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NBo Tu <tubo@linux.vnet.ibm.com>
Message-id: 1460472980-26319-5-git-send-email-silbe@linux.vnet.ibm.com
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Signed-off-by: NMax Reitz <mreitz@redhat.com>

The previous commit removed the last usage of ${tmp} inside the tests
themselves; the only remaining users are sourced by check. So we can now
drop this variable from the tests.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NBo Tu <tubo@linux.vnet.ibm.com>
Message-id: 1460472980-26319-4-git-send-email-silbe@linux.vnet.ibm.com
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Signed-off-by: NMax Reitz <mreitz@redhat.com>

_do() was never used and possibly creates temporary files at
predictable, world-writable locations. Get rid of it.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NBo Tu <tubo@linux.vnet.ibm.com>
Message-id: 1460472980-26319-3-git-send-email-silbe@linux.vnet.ibm.com
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Signed-off-by: NMax Reitz <mreitz@redhat.com>

_within_tolerance() isn't used anymore and possibly creates temporary
files at predictable, world-writable locations. Get rid of it.

If it's needed again in the future it can be revived easily and fixed up
to use TEST_DIR and / or safely created temporary files.
Signed-off-by: NSascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: NBo Tu <tubo@linux.vnet.ibm.com>
Message-id: 1460472980-26319-2-git-send-email-silbe@linux.vnet.ibm.com
Reviewed-by: NMax Reitz <mreitz@redhat.com>
Signed-off-by: NMax Reitz <mreitz@redhat.com>

Signed-off-by: NMarc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1460566660-19241-1-git-send-email-marcandre.lureau@redhat.com>
Reviewed-by: NIgor Mammedov <imammedo@redhat.com>
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>

Pflash migration (e.g. q35 + EFI variable storage) fails
with the assert:

bdrv_co_do_pwritev: Assertion `!(bs->open_flags & 0x0800)' failed.

This avoids the problem by delaying the pflash update until after
the device loads complete.

Tested by:
  Migrating Q35/EFI vm.
  Changing efi variable content (with efiboot in the guest)
  md5sum'ing the variable file before migration and after.

This is a fix that Paolo posted in the message
  570244B3.4070105@redhat.com
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NDr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: NLaszlo Ersek <lersek@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

Commit 57d6a428 neglected to pass the given flags to blk_aio_prwv(),
which broke discard by WRITE SAME for scsi-disk (the UNMAP bit would be
ignored).

Commit fc1453cd introduced the same bug for blk_write_zeroes(). This is
used for 'qemu-img convert' without has_zero_init (e.g. on a block
device) and for preallocation=falloc in parallels.

Commit 8896e088 is the version for blk_co_write_zeroes(). This function
is only used in qemu-io.
Reported-by: NMax Reitz <mreitz@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>