Skip to content

Q
qemu

openeuler / qemu

通知 10
Star 0
Fork 0
Q
qemu

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 01 9月, 2013 2 次提交
  3. 23 8月, 2013 3 次提交
  5. 22 8月, 2013 5 次提交
  7. 21 8月, 2013 1 次提交
  9. 19 8月, 2013 10 次提交
  11. 12 8月, 2013 1 次提交
  13. 06 8月, 2013 8 次提交
  15. 02 8月, 2013 2 次提交
  17. 30 7月, 2013 1 次提交
  19. 29 7月, 2013 1 次提交
  21. 27 7月, 2013 3 次提交
    • S
      misc: Fix new typos in comments and strings · 52f35022
      由 Stefan Weil 提交于 
      All these typos were found by codespell.

sould -> should
emperical -> empirical
intialization -> initialization
successfuly -> successfully
gaurantee -> guarantee

Fix also another error (before before) in the same context.
Signed-off-by: NStefan Weil <sw@weilnetz.de>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NMichael Tokarev <mjt@tls.msk.ru>
      52f35022
    • I
      Implement sync modes for drive-backup. · fc5d3f84
      由 Ian Main 提交于 
      This patch adds sync-modes to the drive-backup interface and
implements the FULL, NONE and TOP modes of synchronization.

FULL performs as before copying the entire contents of the drive
while preserving the point-in-time using CoW.
NONE only copies new writes to the target drive.
TOP copies changes to the topmost drive image and preserves the
point-in-time using CoW.

For sync mode TOP are creating a new target image using the same backing
file as the original disk image.  Then any new data that has been laid
on top of it since creation is copied in the main backup_run() loop.
There is an extra check in the 'TOP' case so that we don't bother to copy
all the data of the backing file as it already exists in the target.
This is where the bdrv_co_is_allocated() is used to determine if the
data exists in the topmost layer or below.

Also any new data being written is intercepted via the write_notifier
hook which ends up calling backup_do_cow() to copy old data out before
it gets overwritten.

For mode 'NONE' we create the new target image and only copy in the
original data from the disk image starting from the time the call was
made.  This preserves the point in time data by only copying the parts
that are *going to change* to the target image.  This way we can
reconstruct the final image by checking to see if the given block exists
in the new target image first, and if it does not, you can get it from
the original image.  This is basically an optimization allowing you to
do point-in-time snapshots with low overhead vs the 'FULL' version.

Since there is no old data to copy out the loop in backup_run() for the
NONE case just calls qemu_coroutine_yield() which only wakes up after
an event (usually cancel in this case).  The rest is handled by the
before_write notifier which again calls backup_do_cow() to write out
the old data so it can be preserved.
Signed-off-by: NIan Main <imain@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      fc5d3f84
    • K
      qcow2: Use dashes instead of underscores in options · 64aa99d3
      由 Kevin Wolf 提交于 
      This is what QMP wants to use. The options haven't been enabled in any
release yet, so we're still free to change them.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>
      64aa99d3
  23. 19 7月, 2013 3 次提交