Request up to 3 vectors in virtio-net. Actual bindings might supply
less.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add pci_get/set_byte to keep *_word and *_long access functions company.
They are unused for now.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Implement bindings for virtio save/load. Use them in virtio pci.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

This enables actual support for MSI-X in virtio PCI.
First user will be virtio-net.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Extend virtio to support many interrupt vectors, and rearrange code in
preparation for multi-vector support (mostly move reset out to bindings,
because we will have to reset the vectors in transport-specific code).
Actual bindings in pci, and use in net, to follow.
Load and save are not connected to bindings yet, so they are left
stubbed out for now.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Implement MSI support in APIC. Note that MSI and MMIO APIC registers
are at the same memory location, but actually not on the global bus: MSI
is on PCI bus, APIC is connected directly to the CPU. We map them on the
global bus at the same address which happens to work because MSI
registers are reserved in APIC MMIO and vice versa.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add functions implementing MSI-X support. First user will be virtio-pci.
Note that platform must set a flag to declare MSI supported: this
is a safety measure to avoid breaking platforms which should support
MSI-X but currently lack this in the interrupt controller emulation.
For PC this will be set by APIC.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add "cmask" table of constant register masks: if a bit is not writeable
and is set in cmask table, this bit is checked on load.  An attempt to
load an image that would change such a register causes load to fail.
Use this table to make sure that load does not modify registers that
guest can not change (directly or indirectly).

Note: we can't just assume that read-only registers never change,
because the guest could change a register indirectly.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add routines to manage PCI capability list. First user will be MSI-X.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add inline routines for convenient access to pci devices
with correct (little) endianness. Will be used by MSI-X support.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Change much of hw/pci to use symbolic constants and a table-driven
design: add a mask table with writable bits set and readonly bits unset.
Detect change by comparing original and new registers.

This makes it easy to support capabilities where read-only/writeable
bit layout differs between devices, depending on capabilities present.

As a result, writing a single byte in BAR registers now works as
it should. Writing to upper limit registers in the bridge
also works as it should. Code is also shorter.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add sparc64 to default list of softmmu targets
Signed-off-by: NIgor V. Kovalenko <igor.v.kovalenko@gmail.com>

sun4u.c: correct pci_nic_init arguments following
commit 5607c388Signed-off-by: NIgor V. Kovalenko <igor.v.kovalenko@gmail.com>

Microblaze recently changed their ABI. The new is not backwards compatible
and there doesn't seem to be a way to distinguish old/new binaries.
Let's support the latest ABI for now and hope someone figures out a way to
hande both ABI's later.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@gmail.com>

Access to the PVR SPR is normally forbidden from userspace apps.  The
Linux kernel, however, fixes up reads in the appropriate trap handler.
To permit applications that read PVR to run on QEMU, then, we need to
implement the same handling of PVR reads.
Signed-off-by: NNathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Nmalc <av1474@comtv.ru>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@gmail.com>

Maximum alignment for Win32 is 16, so don't try
to set it to 32. Otherwise the compiler complains:

exec.c:102: warning: alignment of 'code_gen_prologue'
is greater than maximum object file alignment.  Using 16
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

`sdl-config --cflags` defines main = SDL_main
on some platforms. One of these platforms is
Windows with mingw32.

For those platforms, the solution already developed
for __APPLE__ is now applied.

A compiler warning (missing return value) is fixed, too.

Maybe __APPLE__ no longer needs a separate check.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

virtio-net needs this - for the same purpose that it currently uses the
return value from qemu_sendv_packet().
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

2.6.30 adds a new TUNSETSNDBUF ioctl() which allows a send buffer limit
for the tap device to be specified. When this limit is reached, a tap
write() will return EAGAIN and poll() will indicate the fd isn't
writable.

This allows people to tune their setups so as to avoid e.g. UDP packet
loss when the sending application in the guest out-runs the NIC in the
host.

There is no obviously sensible default setting - a suitable value
depends mostly on the capabilities of the physical NIC through which the
packets are being sent.

Also, note that when using a bridge with netfilter enabled, we currently
never get EAGAIN because netfilter causes the packet to be immediately
orphaned. Set /proc/sys/net/bridge/bridge nf-call-iptables to zero to
disable this behaviour.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

net_tap_fd_init() already returns TAPState, so this is a sensible
cleanup in its own right.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

If a write() on tapfd returns EAGAIN, return zero so that the packet
gets queued (in the case of async send) and enable polling tapfd for
writing.

When tapfd becomes writable, disable write polling and flush any queued
packets.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Add a helper to enable/disable the read polling on tapfd.

We need this, because we want to start write polling on the tapfd too
and enable/disable both types of polling independently.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

If tap has any packets queued at host_net_remove time, it needs to purge
them in order to prevent a sent callback being invoked for it.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

If net client sends packets asynchronously, it needs to purge its queued
packets in cleanup() so as to prevent sent callbacks being invoked with
a freed client.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

APIC reset handler already resets cpu, no need to reset it twice.
Also register cpu_reset handler directly to make it impossible to
add additional code to main_cpu_reset() by mistake.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Make drive_init() accept addr=, put the value into struct DriveInfo.
Use it in all the places that create virtio-blk-pci devices:
pc_init1(), bamboo_init(), mpc8544ds_init().

Don't support addr= in third argument of monitor command pci_add and
second argument of drive_add, because that clashes with their first
arguments.  Admittedly unelegant.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Simply pass the PCI address through qemu_pci_hot_add_nic() to
pci_nic_init() and through qemu_pci_hot_add_storage() to pci_create().

Before, pci_device_hot_add() passed along the PCI bus to use, and
ignored any user-specified slot.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Make net_client_init() accept addr=, put the value into struct
NICinfo.  Use it in pci_nic_init(), and remove arguments bus and
devfn.

Don't support addr= in third argument of monitor command pci_add,
because that clashes with its first argument.  Admittedly unelegant.

Machines "malta" and "r2d" have a default NIC with a well-known PCI
address.  Deal with that the same way as the NIC model: make
pci_nic_init() take an optional default to be used when the user
doesn't specify one.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

use NULL instead of 0 for pci_register_device() argument
for consistency. Any other caller uses NULL.
Signed-off-by: NIsaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

add qemu-monitor.texi to .gitignore.
Signed-off-by: NIsaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

When virtio-net was merged in from qemu-kvm.git, the VNET_HDR related
features were dropped from the code.

However, VIRTIO_NET_F_MRG_RXBUF appears to have accidentally been
dropped too. Re-instate that now.
Reported-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

introruce piix4_device_hot_add() for piix4 specific code
and make qemu_system_device_hot_add() generic.
Signed-off-by: NIsaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

Otherwise, after migration, we end up with a much larger RSS size then we
ought to have.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

This should fix compilation problem in case of CONFIG_USER_ONLY.

Currently INIT/SIPI is handled in the context of CPU that sends IPI.
This patch changes this to handle them like all other events in a main
cpu exec loop. When KVM will gain thread per vcpu capability it will
be much more clear to handle those event by cpu thread itself and not
modify one cpu's state from the context of the other.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

To reset internal irq handling data structures.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NYaniv Kamay <ykamay@redhat.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>