When we add werror=stop or rerror=stop support to NCQ,
we'll want to take a codepath where we don't actually
complete the command, so factor that out into a new routine.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-6-git-send-email-jsnow@redhat.com

Split off execute_ncq_command so that we can call
it separately later if we desire.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-5-git-send-email-jsnow@redhat.com

We already checked this in the handle_cmd phase, so just
change this to an assertion and simplify the error logic.

(Also, fix the switch indent, because checkpatch.pl yelled.)
((Sorry for churn.))
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-4-git-send-email-jsnow@redhat.com

For migration and werror=stop/rerror=stop resume purposes,
it will be convenient to have the command handy inside of
ncq_tfs.

Eventually, we'd like to avoid reading from the FIS entirely
after the initial read, so this is a byte (hah!) sized step
in that direction.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-3-git-send-email-jsnow@redhat.com

prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.

For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.

PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.

AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.

Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.

This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.

For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com

Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-17-git-send-email-jsnow@redhat.com

Test the NCQ pathways for a simple IO RW test.
Also, test that libqos doesn't explode when
running NCQ commands :)
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-16-git-send-email-jsnow@redhat.com

NCQ commands are LBA48 by definition.

See SATA 3.2 13.6.4.1 "READ FPDMA QUEUED", or
    SATA 3.2 13.6.5.1 "WRITE FPDMA QUEUED."
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-15-git-send-email-jsnow@redhat.com

NCQ commands have the concept of a "TAG" that they need to set,
but in the AHCI world, it is mandated that the TAG always match
the command slot that you executed the NCQ from.

See AHCI 9.3.1.1.5.2 "Native Queued Commands".
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-14-git-send-email-jsnow@redhat.com

NCQ commands will expect the SDBS interrupt,
and in the normative case, do not expect to see
a D2H Register FIS unless something went wrong.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-13-git-send-email-jsnow@redhat.com

The wait command should check to make sure SACT is clear as well
as the Command Issue register.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-12-git-send-email-jsnow@redhat.com

NCQ frames are generated a little differently than
their non-NCQ cousins. Add support for them.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-11-git-send-email-jsnow@redhat.com

NCQ commands should not / do not update the byte count
in the command header post command, so this field is
meaningless for NCQ tests.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-10-git-send-email-jsnow@redhat.com

If you try to execute an NCQ command before trying to engage with the
device by issuing an IDENTIFY command, the error bits that are part of
the signature will fool the test suite into thinking there was a failure.

Issue IDENTIFY first on "boot", which will clear the signature out of
the registers for us.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-9-git-send-email-jsnow@redhat.com

This value should not be size-corrected, 0 sectors does not imply
1 sector(s). This is just debug information, but it's misleading!
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-8-git-send-email-jsnow@redhat.com

Most of the time, these bits can be safely ignored. For the purposes
of debugging however, it's nice to know that they're not being used.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-7-git-send-email-jsnow@redhat.com

There's no real reason to have it bundled together, and this way
is a little nicer to follow if you have the AHCI spec pulled up.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-6-git-send-email-jsnow@redhat.com

Don't attempt the NCQ transfer if the PRDT we were given is not big
enough to perform the entire transfer.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-5-git-send-email-jsnow@redhat.com

Set some appropriate error bits for NCQ for us.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-4-git-send-email-jsnow@redhat.com

Trivial cleanup that I didn't want to tack-on to anything else.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-3-git-send-email-jsnow@redhat.com

Several fields of the NCQFIS structure are ambiguously named. This patch
clarifies the intended (if unsupported) usage of the NCQ fields to aid
in creating more meaningful debug messages through the NCQ codepaths.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-2-git-send-email-jsnow@redhat.com

Test that we can survive a couple of cycles of running a basic identify
test, some IO, and resetting the HBA. Ensures that we can bring the HBA
back to compliant spec during the lifecycle of the VM.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Message-id: 1434470575-21625-5-git-send-email-jsnow@redhat.com

There's a handful of trivial bugs in the libqos/ahci functions,
squish them together.

- Zero cached pointers after freeing them
- The Command List Buffer is an array of 32x 32 byte structures, not
  32x 8 byte pointers -- it's 1MiB, not 256 bytes. Zero it ALL.
- Free the correct command in ahci_pick_cmd.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Message-id: 1434470575-21625-4-git-send-email-jsnow@redhat.com

Test that the FIS delivered after a nondata command has appropriately
updated registers, just as we'd expect a data command to do.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Message-id: 1434470575-21625-3-git-send-email-jsnow@redhat.com

The only guidance the AHCI specification gives on memory access is:
"Register accesses shall have a maximum size of 64-bits; 64-bit access
must not cross an 8-byte alignment boundary."

I interpret this to mean that aligned or unaligned 1, 2 and 4 byte
accesses should work, as well as aligned 8 byte accesses.

In practice, a real Q35/ICH9 responds to 1, 2, 4 and 8 byte reads
regardless of alignment. Windows 7 can be observed making 1 byte
reads to the middle of 32 bit registers to fetch error codes.

Introduce a wrapper to support unaligned accesses to AHCI.
This wrapper will support aligned 8 byte reads, but will make
no effort to support unaligned 8 byte reads, which although they
will work on real hardware, are not guaranteed to work and do
not appear to be used by either Windows or Linux.
Signed-off-by: NJohn Snow <jsnow@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>
Message-id: 1434470575-21625-2-git-send-email-jsnow@redhat.com

virtio-input: add input routing support, update multiseat docs.

# gpg: Signature made Fri Jul  3 11:22:33 2015 BST using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg:                 aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg:                 aka "Gerd Hoffmann (private) <kraxel@gmail.com>"

* remotes/kraxel/tags/pull-input-20150703-1:
  update pci-bridge-seat section in docs/multiseat.txt
  virtio-input: add input routing support
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Add display and head properties for input routing to
virtio-input devices, update multiseat documentation.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Several s390x patches including:
- missing virtio-1 related code for virtio-ccw
- bugfixes in ipl device, gdb, virtio-ccw
- bugfix in s390-ccw bios + rebuild
- introduce versioned machines for s390-ccw-virtio

# gpg: Signature made Thu Jul  2 15:05:34 2015 BST using RSA key ID C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg:                 aka "Cornelia Huck <cornelia.huck@de.ibm.com>"

* remotes/cohuck/tags/s390x-20150702-v3:
  s390x/migration: Introduce 2.4 machine
  s390x/gdb: synchronize cpu state after modifying acrs
  s390x/ipl: Fix boot if no bootindex was specified
  virtio-ccw: migrate ->revision
  s390x/virtio-ccw: support virtio-1 set_vq format
  s390x/virtio-ccw: add virtio set-revision call
  s390x/css: Add a callback for when subchannel gets disabled
  s390-ccw.img: update
  s390-ccw.img: Consume service interrupts
  css: mss/mcss-e vs. migration
  virtio-ccw: complete handling of guest-initiated resets
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

The section footer changes commit f68945d4 ("Add a protective
section footer") and commit 37fb569c ("Disable section footers
on older machine types") broke migration for any non-versioned
machines.

This pinpoints a problem of s390-ccw machines: it needs to
be versioned to be compatible with future changes in common
code data structures such as section footers.

Let's introduce a version scheme for s390-ccw-virtio machines.
We will use the old s390-ccw-virtio name as alias to the latest
version as all existing libvirt XML for the ccw type were expanded
by libvirt to that name.

The only downside of this patch is, that the old alias s390-ccw
will no longer be available as machines can have only one alias,
but it should not really matter.

Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1435742217-62246-1-git-send-email-borntraeger@de.ibm.com>
Reviewed-by: NJuan Quintela <quintela@redhat.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Whenever we touch the access control registers, we have to make sure that
the values will make it into kvm. Otherwise the change will simply be lost.

When synchronizing qemu and kvm, a normal KVM_PUT_RUNTIME_STATE does not take
care of these registers. Let's simply trigger a KVM_PUT_FULL_STATE sync,
so the values will directly be written to kvm. The performance overhead can
be ignored and this is much cleaner than manually writing these registers to kvm
via our two supported ways.
Reviewed-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

commit fa92e218 ("s390x/ipl: avoid sign extension") introduced
a regression:

qemu-system-s390x -drive file=image.qcow,format=qcow2
does not boot, the bios states
"No virtio-blk device found!"

adding bootindex=1 does boot.

The reason is that the uint32_t as return value will not do the right
thing for the return -1 (default without bootindex).
The bios itself, will interpret a 64bit -1 as autodetect (but it will
interpret 32bit -1 as ccw device address ff.ff.ffff)
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: qemu-stable@nongnu.org # v2.3.0
Tested-by: NAurelien Jarno <aurelien@aurel32.net>
Reviewed-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

We need to migrate the revision field as well. No compatibility
concerns as we already introduced migration of ->config_vector in
this release.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Support the new CCW_CMD_SET_VQ format for virtio-1 devices.

While we're at it, refactor the code a bit and enforce big endian
fields (which had always been required, even for legacy).
Reviewed-by: NThomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>

Handle the virtio-ccw revision according to what the guest sets.
When revision 1 is selected, we have a virtio-1 standard device
with byteswapping for the virtio rings.

When a channel gets disabled, we have to revert to the legacy behavior
in case the next user of the device does not negotiate the revision 1
anymore (e.g. the boot firmware uses revision 1, but the operating
system only uses the legacy mode).

Note that revisions > 0 are still disabled.

[CH: assure memory accesses are always BE]
Signed-off-by: NThomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Thu Jul  2 10:10:39 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg:                 aka "Stefan Hajnoczi <stefanha@gmail.com>"

* remotes/stefanha/tags/block-pull-request:
  block: remove redundant check before g_slist_find()
  block/nfs: limit maximum readahead size to 1MB
  block/iscsi: restore compatiblity with libiscsi 1.9.0
  iotests: Use event_wait in wait_ready
  qemu-iotests: Add test case for mirror with unmap
  qemu-iotests: Make block job methods common
  block: Remove bdrv_reset_dirty
  block: Fix dirty bitmap in bdrv_co_discard
  mirror: Do zero write on target if sectors not allocated
  qmp: Add optional bool "unmap" to drive-mirror
  block: Add bdrv_get_block_status_above
  timer: Use a single definition of NSEC_PER_SEC for the whole codebase
  timer: Move NANOSECONDS_PER_SECONDS to timer.h
  blockdev: no need to drain+flush in hmp_drive_del
  qapi: Rename 'dirty-bitmap' mode to 'incremental'
  qcow2: Handle EAGAIN returned from update_refcount
  block/iscsi: add support for request timeouts
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

An empty GSList is represented by a NULL pointer, therefore it's a
perfectly valid argument for g_slist_find() and there's no need to
make any additional check.
Signed-off-by: NAlberto Garcia <berto@igalia.com>
Message-id: 1435583533-5758-1-git-send-email-berto@igalia.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

a malicious caller could otherwise specify a very
large value via the URI and force libnfs to allocate
a large amount of memory for the readahead buffer.

Cc: qemu-stable@nongnu.org
Signed-off-by: NPeter Lieven <pl@kamp.de>
Message-id: 1435317241-25585-1-git-send-email-pl@kamp.de
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

RHEL7 and others are stuck with libiscsi 1.9.0 since there
unfortunately was an ABI breakage after that release.
Signed-off-by: NPeter Lieven <pl@kamp.de>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Message-id: 1435313881-19366-1-git-send-email-pl@kamp.de
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Only poll the specific type of event we are interested in, to avoid
stealing events that should be consumed by someone else.
Suggested-by: NJohn Snow <jsnow@redhat.com>
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NJohn Snow <jsnow@redhat.com>
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>