The tmp105 test is currently not executed since the following
line in the Makefile overwrites the check-qtest-arm-y variable
instead of extending it.
Signed-off-by: NThomas Huth <thuth@redhat.com>
Message-id: 1466760306-21849-1-git-send-email-thuth@redhat.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

The Cadence GEM data sheet says:
"Wrap - marks last descriptor in transmit buffer descriptor list. This
can be set for any buffer within the frame."
which seems to imply that when the wrap bit is set so is the last bit.

Previously if the wrap bit is set, but the last is not then QEMU will
enter an infinite loop.
Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com>
Reported-by: NLi Qiang <liqiang6-s@360.cn>
Reported-by: NP J P <ppandit@redhat.com>
Message-id: eb23f15c67989ea6a53609dc66568399dadf52a7.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

A guest can write zero to the DMACFG resulting in an infinite loop when
it reaches the while(bytes_to_copy) loop.

To avoid this issue enforce a minimum size for the RX buffer. Hardware
does not have this enforcement and relies on the guest to set a non-zero
value.
Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com>
Reported-by: NLi Qiang <liqiang6-s@360.cn>
Reported-by: NP J P <ppandit@redhat.com>
Message-id: 84bb1c391b833275da3f573d4972920cea34c188.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

If qemu_chr_fe_write() returns an error (represented by a negative
number) we should skip incrementing the count and initiating a
memmove().
Signed-off-by: NAlistair Francis <alistair.francis@xilinx.com>
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

These are spotted by coverity 1356936 and 1356937.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

ppc patch queue for 2016-06-27

Small queue this time.  Main reason for sending it is the pair of
patches to fix up the new cpu hotplug model used on Power to what
should be an actually usable state.  There's also a small BookE bugfix
and a XICS trivial cleanup.

# gpg: Signature made Mon 27 Jun 2016 06:28:37 BST
# gpg:                using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg:                 aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg:                 aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E  87DC 6C38 CACA 20D9 B392

* remotes/dgibson/tags/ppc-for-2.7-20160627:
  qapi: keep names in 'CpuInstanceProperties' in sync with struct CPUCore
  qapi: Report support for -device cpu hotplug in query-machines
  ppc/xics: Remove unused xics_set_irq_type()
  target-ppc: ppce500_spin.c uses SPR_PIR, should use SPR_BOOKE_PIR
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

MIPS patches 2016-06-24

Changes:
* support IEEE 754-2008 in MIPS CPUs

# gpg: Signature made Fri 24 Jun 2016 16:09:38 BST
# gpg:                using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4  4FC0 5211 8E3C 0B29 DA6B

* remotes/lalrae/tags/mips-20160624:
  target-mips: Add FCR31's FS bit definition
  target-mips: Implement FCR31's R/W bitmask and related functionalities
  target-mips: Add nan2008 flavor of <CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>
  target-mips: Add abs2008 flavor of <ABS|NEG>.<S|D>
  target-mips: Activate IEEE 754-2008 signaling NaN bit meaning for MSA
  linux-user: Update preprocessor constants for Mips-specific e_flags bits
  softfloat: Handle snan_bit_is_one == 0 in MIPS pickNaNMulAdd()
  softfloat: For Mips only, correct default NaN values
  softfloat: Clean code format in fpu/softfloat-specialize.h
  softfloat: Implement run-time-configurable meaning of signaling NaN bit
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

qemu-sparc update

# gpg: Signature made Fri 24 Jun 2016 18:19:36 BST
# gpg:                using RSA key 0x5BC2C56FAE0F321F
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>"
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C  C9C4 5BC2 C56F AE0F 321F

* remotes/mcayland/tags/qemu-sparc-signed:
  target-sparc: fix register corruption in ldstub if there is no write permission
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

struct CPUCore uses 'id' suffix in the property name. As docs for
query-hotpluggable-cpus state that the cpu core properties should be
passed back to device_add by management in case new members are added
and thus the names for the fields should be kept in sync.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>
Reviewed-by: NIgor Mammedov <imammedo@redhat.com>
[dwg: Removed a duplicated word in comment]
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

For management apps it's very useful to know whether the selected
machine type supports cpu hotplug via the new -device approach. Using
the presence of 'query-hotpluggable-cpus' alone is not enough as a
witness.

Add a property to 'MachineInfo' called 'hotpluggable-cpus' that will
report the presence of this feature.

Example of output:
    {
        "hotpluggable-cpus": false,
        "name": "mac99",
        "cpu-max": 1
    },
    {
        "hotpluggable-cpus": true,
        "name": "pseries-2.7",
        "is-default": true,
        "cpu-max": 255,
        "alias": "pseries"
    },
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>
Reviewed-by: NIgor Mammedov <imammedo@redhat.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NNikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

ppce500_spin.c uses SPR_PIR to initialize the spin table, however on
Book E processors the correct SPR is SPR_BOOKE_PIR.
Signed-off-by: NAaron Larson <alarson@ddci.com>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

Signed-off-by: NArtyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NMark Cave-Ayland <mark.cave-ayland@ilande.co.uk>

Add preprocessor definition of FCR31's FS bit, and update related
code for setting this bit.
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

This patch implements read and write access rules for Mips floating
point control and status register (FCR31). The change can be divided
into following parts:

- Add fields that will keep FCR31's R/W bitmask in procesor
  definitions and processor float_status structure.

- Add appropriate value for FCR31's R/W bitmask for each supported
  processor.

- Add function for setting snan_bit_is_one, and integrate it in
  appropriate places.

- Modify handling of CTC1 (case 31) instruction to use FCR31's R/W
  bitmask.

- Modify handling user mode executables for Mips, in relation to the
  bit EF_MIPS_NAN2008 from ELF header, that is in turn related to
  reading and writing to FCR31.

- Modify gdb behavior in relation to FCR31.
Signed-off-by: NThomas Schwinge <thomas@codesourcery.com>
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

New set of helpers for handling nan2008-syle versions of instructions
<CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>, for Mips R6.

All involved instructions have float operand and integer result. Their
core functionality is implemented via invocations of appropriate SoftFloat
functions. The problematic cases are when the operand is a NaN, and also
when the operand (float) is out of the range of the result.

Here one can distinguish three cases:

CASE MIPS-A: (FCR31.NAN2008 == 1)

   1. Operand is a NaN, result should be 0;
   2. Operand is larger than INT_MAX, result should be INT_MAX;
   3. Operand is smaller than INT_MIN, result should be INT_MIN.

CASE MIPS-B: (FCR31.NAN2008 == 0)

   1. Operand is a NaN, result should be INT_MAX;
   2. Operand is larger than INT_MAX, result should be INT_MAX;
   3. Operand is smaller than INT_MIN, result should be INT_MAX.

CASE SoftFloat:

   1. Operand is a NaN, result is INT_MAX;
   2. Operand is larger than INT_MAX, result is INT_MAX;
   3. Operand is smaller than INT_MIN, result is INT_MIN.

Current implementation of <CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>
implements case MIPS-B. This patch relates to case MIPS-A. For case
MIPS-A, only return value for NaN-operands should be corrected after
appropriate SoftFloat library function is called.

Related MSA instructions FTRUNC_S and FTINT_S already handle well
all cases, in the fashion similar to the code from this patch.
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com:
 * removed a statement from the description which caused slight confusion]
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Updated handling of instructions <ABS|NEG>.<S|D>. Note that legacy
(pre-abs2008) ABS and NEG instructions are arithmetic (and, therefore,
any NaN operand causes signaling invalid operation), while abs2008
ones are non-arithmetic, always and only changing the sign bit, even
for NaN-like operands. Details on these instructions are documented
in [1] p. 35 and 359.

Implementation-wise, abs2008 versions are implemented without helpers,
for simplicity and performance sake.

[1] "MIPS Architecture For Programmers Volume II-A:
    The MIPS64 Instruction Set Reference Manual",
    Imagination Technologies LTD, Revision 6.04, November 13, 2015
Signed-off-by: NThomas Schwinge <thomas@codesourcery.com>
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Function msa_reset() is updated so that flag snan_bit_is_one is
properly set to 0.

By applying this patch, a number of incorrect MSA behaviors that
require IEEE 754-2008 compliance will be fixed. Those are behaviors
that (up to the moment of applying this patch) did not get the desired
functionality from SoftFloat library with respect to distinguishing
between quiet and signaling NaN, getting default NaN values (both
quiet and signaling), establishing if a floating point number is NaN
or not, etc.

Two examples:

* FMAX, FMIN will now correctly detect and propagate NaNs.
* FCLASS.D ans FCLASS.S will now correcty detect NaN flavors.
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Missing values EF_MIPS_FP64 and EF_MIPS_NAN2008 added.
Signed-off-by: NThomas Schwinge <thomas@codesourcery.com>
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct the order of argument comparisons in pickNaNMulAdd().

For more info, see [1], page 53, section "3.5.3 NaN Propagation".

[1] "MIPS Architecture for Programmers Volume IV-j:
    The MIPS32 SIMD Architecture Module",
    Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
 * reworded the subject of the patch
 * swapped if/else code blocks to match the commit description]
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Only for Mips platform, and only for cases when snan_bit_is_one is 0,
correct default NaN values (in their 16-, 32-, and 64-bit flavors).

For more info, see [1], page 84, Table 6.3 "Value Supplied When a New
Quiet NaN Is Created", and [2], page 52, Table 3.7 "Default NaN
Encodings".

[1] "MIPS Architecture For Programmers Volume II-A:
    The MIPS64 Instruction Set Reference Manual",
    Imagination Technologies LTD, Revision 6.04, November 13, 2015

[2] "MIPS Architecture for Programmers Volume IV-j:
    The MIPS32 SIMD Architecture Module",
    Imagination Technologies LTD, Revision 1.12, February 3, 2016
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

fpu/softfloat-specialize.h is the most critical file in SoftFloat
library, since it handles numerous differences between platforms in
relation to floating point arithmetics. This patch makes the code
in this file more consistent format-wise, and hopefully easier to
debug and maintain.
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

This patch modifies SoftFloat library so that it can be configured in
run-time in relation to the meaning of signaling NaN bit, while, at the
same time, strictly preserving its behavior on all existing platforms.

Background:

In floating-point calculations, there is a need for denoting undefined or
unrepresentable values. This is achieved by defining certain floating-point
numerical values to be NaNs (which stands for "not a number"). For additional
reasons, virtually all modern floating-point unit implementations use two
kinds of NaNs: quiet and signaling. The binary representations of these two
kinds of NaNs, as a rule, differ only in one bit (that bit is, traditionally,
the first bit of mantissa).

Up to 2008, standards for floating-point did not specify all details about
binary representation of NaNs. More specifically, the meaning of the bit
that is used for distinguishing between signaling and quiet NaNs was not
strictly prescribed. (IEEE 754-2008 was the first floating-point standard
that defined that meaning clearly, see [1], p. 35) As a result, different
platforms took different approaches, and that presented considerable
challenge for multi-platform emulators like QEMU.

Mips platform represents the most complex case among QEMU-supported
platforms regarding signaling NaN bit. Up to the Release 6 of Mips
architecture, "1" in signaling NaN bit denoted signaling NaN, which is
opposite to IEEE 754-2008 standard. From Release 6 on, Mips architecture
adopted IEEE standard prescription, and "0" denotes signaling NaN. On top of
that, Mips architecture for SIMD (also known as MSA, or vector instructions)
also specifies signaling bit in accordance to IEEE standard. MSA unit can be
implemented with both pre-Release 6 and Release 6 main processor units.

QEMU uses SoftFloat library to implement various floating-point-related
instructions on all platforms. The current QEMU implementation allows for
defining meaning of signaling NaN bit during build time, and is implemented
via preprocessor macro called SNAN_BIT_IS_ONE.

On the other hand, the change in this patch enables SoftFloat library to be
configured in run-time. This configuration is meant to occur during CPU
initialization, at the moment when it is definitely known what desired
behavior for particular CPU (or any additional FPUs) is.

The change is implemented so that it is consistent with existing
implementation of similar cases. This means that structure float_status is
used for passing the information about desired signaling NaN bit on each
invocation of SoftFloat functions. The additional field in float_status is
called snan_bit_is_one, which supersedes macro SNAN_BIT_IS_ONE.

IMPORTANT:

This change is not meant to create any change in emulator behavior or
functionality on any platform. It just provides the means for SoftFloat
library to be used in a more flexible way - in other words, it will just
prepare SoftFloat library for usage related to Mips platform and its
specifics regarding signaling bit meaning, which is done in some of
subsequent patches from this series.

Further break down of changes:

  1) Added field snan_bit_is_one to the structure float_status, and
     correspondent setter function set_snan_bit_is_one().

  2) Constants <float16|float32|float64|floatx80|float128>_default_nan
     (used both internally and externally) converted to functions
     <float16|float32|float64|floatx80|float128>_default_nan(float_status*).
     This is necessary since they are dependent on signaling bit meaning.
     At the same time, for the sake of code cleanup and simplicity, constants
     <floatx80|float128>_default_nan_<low|high> (used only internally within
     SoftFloat library) are removed, as not needed.

  3) Added a float_status* argument to SoftFloat library functions
     XXX_is_quiet_nan(XXX a_), XXX_is_signaling_nan(XXX a_),
     XXX_maybe_silence_nan(XXX a_). This argument must be present in
     order to enable correct invocation of new version of functions
     XXX_default_nan(). (XXX is <float16|float32|float64|floatx80|float128>
     here)

  4) Updated code for all platforms to reflect changes in SoftFloat library.
     This change is twofolds: it includes modifications of SoftFloat library
     functions invocations, and an addition of invocation of function
     set_snan_bit_is_one() during CPU initialization, with arguments that
     are appropriate for each particular platform. It was established that
     all platforms zero their main CPU data structures, so snan_bit_is_one(0)
     in appropriate places is not added, as it is not needed.

[1] "IEEE Standard for Floating-Point Arithmetic",
    IEEE Computer Society, August 29, 2008.
Signed-off-by: NThomas Schwinge <thomas@codesourcery.com>
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NAleksandar Markovic <aleksandar.markovic@imgtec.com>
Tested-by: NBastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
Tested-by: NLeon Alrae <leon.alrae@imgtec.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
 * cherry-picked 2 chunks from patch #2 to fix compilation warnings]
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

pc, pci, virtio: new features, cleanups, fixes

nvdimm label support
cpu acpi hotplug rework
virtio rework
misc cleanups and fixes
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

# gpg: Signature made Fri 24 Jun 2016 06:50:32 BST
# gpg:                using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg:                 aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17  0970 C350 3912 AFBE 8E67
#      Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA  8A0D 281F 0DB8 D28D 5469

* remotes/mst/tags/for_upstream: (34 commits)
  virtio-bus: remove old set_host_notifier callback
  virtio-mmio: convert to ioeventfd callbacks
  virtio-pci: convert to ioeventfd callbacks
  virtio-ccw: convert to ioeventfd callbacks
  virtio-bus: have callers tolerate new host notifier api
  virtio-bus: common ioeventfd infrastructure
  pc: acpi: drop intermediate PCMachineState.node_cpu
  acpi-test-data: update expected
  pc: use new CPU hotplug interface since 2.7 machine type
  acpi: cpuhp: add cpu._OST handling
  acpi: cpuhp: implement hot-remove parts of CPU hotplug interface
  acpi: cpuhp: implement hot-add parts of CPU hotplug interface
  pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
  acpi: cpuhp: add CPU devices AML with _STA method
  pc: piix4/ich9: add 'cpu-hotplug-legacy' property
  docs: update ACPI CPU hotplug spec with new protocol
  i386: pci-assign: Fix MSI-X table size
  docs: add NVDIMM ACPI documentation
  nvdimm acpi: support Set Namespace Label Data function
  nvdimm acpi: support Get Namespace Label Data function
  ...
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

All users have been converted to the new ioevent callbacks.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Convert to the new interface.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Convert to new interface.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Use the new interface.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Have vhost and dataplane use the new api for transports that
have been converted.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Introduce a set of ioeventfd callbacks on the virtio-bus level
that can be implemented by the individual transports. At the
virtio-bus level, do common handling for host notifiers (which
is actually most of it).

Two things of note:
- When setting the host notifier, we only switch from/to the
  generic ioeventfd handler. This fixes a latent bug where we
  had no ioeventfd assigned for a certain window.
- We always iterate over all possible virtio queues, even though
  ccw (currently) has a lower limit. It does not really matter
  here.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

PCMachineState.node_cpu was used for mapping APIC ID
to numa node id as CPU entries in SRAT used to be
built on sparse APIC ID bitmap (up to apic_id_limit).
However since commit
  5803fce3 pc: acpi: SRAT: create only valid processor lapic entries
CPU entries in SRAT aren't build using apic bitmap
but using 0..maxcpus index instead which is also used
for creating numa_info[x].node_cpu map.
So instead of doing useless intermediate conversion from
  1. node by cpu index -> node by apic id
       i.e. numa_info[x].node_cpu -> PCMachineState.node_cpu
  2. apic id -> srat entry PMX
       PCMachineState.node_cpu[apic id] -> PMX value
use numa_info[x].node_cpu map directly like ARM does and do
  1. numa_info[x].node_cpu -> PMX value using index
     in range 0..maxcpus
and drop not necessary PCMachineState.node_cpu and related
code.

That also removes the last (not counting legacy hotplug)
dependency of ACPI code on apic_id_limit and need to allocate
huge sparse PCMachineState.node_cpu array in case of 32-bit
APIC IDs.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

switched to new cpu hotplug interface, aml changed.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

For compatibility reasons PC/Q35 will start with legacy
CPU hotplug interface by default but with new CPU hotplug
AML code since 2.7 machine type. That way legacy firmware
that doesn't use QEMU generated ACPI tables will be
able to continue using legacy CPU hotplug interface.

While new machine type, with firmware supporting QEMU
provided ACPI tables, will generate new CPU hotplug AML,
which will switch to new CPU hotplug interface when
guest OS executes its _INI method on ACPI tables
loading.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it adds HW and AML parts for CPU_Device._OST method
handling to allow OSPM reports status of hot-(un)plug
operation.
And extends QMP command query-acpi-ospm-status to report
CPU's OST info along with already reported PC-DIMM devices.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it adds hw registers needed for handling CPU hot-remove and
corresponding AML methods to request and eject a CPU with
necessary hotplug callbacks in pc,piix4,ich9 code.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it adds hw registers needed for handling CPU hot-add and
corresponding AML methods to handle hot-add events on
guest side.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Add madt_cpu callback to AcpiDeviceIfClass and use
it for generating LAPIC MADT entries for CPUs.

Later it will be used for generating x2APIC
entries in case of more than 255 CPUs and also
would be reused by ARM target when ACPI CPU hotplug
is introduced there.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it adds CPU objects to DSDT with _STA method
and QEMU side of CPU hotplug interface initialization
with registers sufficient to handle _STA requests,
including necessary hotplug callbacks in piix4,ich9 code.

Hot-(un)plug hw/acpi parts will be added by
corresponding follow up patches.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

It will be used to select which hotplug call-back is called
and for switching from legacy mode into new one.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Add description of new CPU hotplug interface.

To switch from from legacy mode into new mode use fact
that write accesses into CPU present bitmap were never
used before and were ignored by QEMU.
So use it to as a way to switch from legacy mode.
That way pc/q35 machine starts in legacy mode and
QEMU generated ACPI tables will switch to new CPU
hotplug interface during runtime.
In case QEMU is started with legacy BIOS (that doesn't
support QEMU generated ACPI tables), legacy CPU hotplug
will remain active and could be used by BIOS built in
ACPI tables for CPU hotplug.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>