The AArch64 FPEXC32_EL2 system register is visible at EL2 and EL3,
and allows those exception levels to read and write the FPEXC
register for a lower exception level that is using AArch32.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: NSergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1453132414-8127-1-git-send-email-peter.maydell@linaro.org

The entry offset when taking an exception to AArch64 from a lower
exception level may be 0x400 or 0x600. 0x400 is used if the
implemented exception level immediately lower than the target level
is using AArch64, and 0x600 if it is using AArch32. We were
incorrectly implementing this as checking the exception level
that the exception was taken from. (The two can be different if
for example we take an exception from EL0 to AArch64 EL3; we should
in this case be checking EL2 if EL2 is implemented, and EL1 if
EL2 is not implemented.)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Handling of semihosting calls should depend on the register width
of the calling code, not on that of any higher exception level,
so we need to identify and handle semihosting calls before we
decide whether to deliver the exception as an entry to AArch32
or AArch64. (EXCP_SEMIHOST is also an "internal exception" so
it has no target exception level in the first place.)

This will allow AArch32 EL1 code to use semihosting calls when
running under an AArch64 EL3.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

If EL2 or EL3 is present on an AArch64 CPU, then exceptions can be
taken to an exception level which is running AArch32 (if only EL0
and EL1 are present then EL1 must be AArch64 and all exceptions are
taken to AArch64). To support this we need to have a single
implementation of the CPU do_interrupt() method which can handle both
32 and 64 bit exception entry.

Pull the common parts of aarch64_cpu_do_interrupt() and
arm_cpu_do_interrupt() out into a new function which calls
either the AArch32 or AArch64 specific entry code once it has
worked out which one is needed.

We temporarily special-case the handling of EXCP_SEMIHOST to
avoid an assertion in arm_el_is_aa64(); the next patch will
pull all the semihosting handling out to the arm_cpu_do_interrupt()
level (since semihosting semantics depend on the register width
of the calling code, not on that of any higher EL).
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Move the aarch64_cpu_do_interrupt() function to helper.c. We want
to be able to call this from code that isn't AArch64-only, and
the move allows us to avoid awkward #ifdeffery at the callsite.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

If we have a secure address space, use it in page table walks:
when doing the physical accesses to read descriptors, make them
through the correct address space.

(The descriptor reads are the only direct physical accesses
made in target-arm/ for CPUs which might have TrustZone.)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Acked-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Implement cpu_get_phys_page_attrs_debug instead of cpu_get_phys_page_debug.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Acked-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>

Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.

This commit was created with scripts/clean-includes.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NDaniel P. Berrange <berrange@redhat.com>
Message-id: 1449505425-32022-3-git-send-email-peter.maydell@linaro.org

arm_regime_using_lpae_format checks whether the LPAE extension is used
for stage 1 translation regimes. MMU indexes not exclusively of a stage 1
regime won't work with this method.

In case of ARMMMUIdx_S12NSE0 or ARMMMUIdx_S12NSE1, offset these values
by ARMMMUIdx_S1NSE0 to get the right index indicating a stage 1
translation regime.

Rename also the function to arm_s1_regime_using_lpae_format and update
the comments to reflect the change.
Signed-off-by: NAlvise Rigo <a.rigo@virtualopensystems.com>
Message-id: 1452854262-19550-1-git-send-email-a.rigo@virtualopensystems.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Qemu does not generally perform alignment checks. However, the ARM ARM
requires implementation of alignment exceptions for a number of cases
including LDREX, and Windows-on-ARM relies on this.

This change adds plumbing to enable alignment checks on loads using
MO_ALIGN, a do_unaligned_access hook to raise the exception (data
abort), and uses the new aligned loads in LDREX (for all but
single-byte loads).
Signed-off-by: NAndrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1449167808-5656-1-git-send-email-Andrew.Baumann@microsoft.com
[PMM: set WnR bits in syndrome and FSR as appropriate]
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

In an LPAE format descriptor in ARMv8 the address field extends
up to bit 47, not just bit 39. Correct the masking so we don't
give incorrect results if the output address size is greater
than 40 bits, as it can be for AArch64.

(Note that we don't yet support the new-in-v8 Address Size fault which
should be generated if any translation table entry or TTBR contains
an address with non-zero bits above the most significant bit of the
maximum output address size.)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NLaurent Desnogues <laurent.desnogues@gmail.com>
Reviewed-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1448029971-9875-1-git-send-email-peter.maydell@linaro.org

Add BANK_<cpumode> #defines to index banked registers.
Suggested-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-15-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Add support for applying S2 translation to 32bit S1
page-table walks.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-13-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Add support for applying S2 translation to 64bit S1
page-table walks.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-12-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Introduce ARMMMUFaultInfo to propagate MMU Fault information
across the MMU translation code path. This is in preparation for
adding Stage-2 translation.

No functional changes.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-11-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Avoid inline for get_phys_addr() to prepare for future recursive use.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-10-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-9-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

The starting level for S2 pagetable walks is computed
differently from the S1 starting level. Implement the S2
variant.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-8-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Rename granule_sz to stride to better match the reference manuals.

No functional change.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-7-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Remove the tsz variable and introduce inputsize.
This simplifies the code a little and makes it easier to
compare with the reference manuals.

No functional change.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-6-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Add support for AArch32 S2 negative t0sz. In preparation for
using 40bit IPAs on AArch32.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-5-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Move declaration of t0sz and t1sz to the top of the function
avoiding a mix of code and variable declarations.

No functional change.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-4-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Make t0sz and t1sz signed integers to match tsz and to make
it easier to implement support for AArch32 negative t0sz.
t1sz is changed for consistensy.

No functional change.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Reviewed-by: NAlex Bennée <alex.bennee@linaro.org>
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1445864527-14520-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Add the MDCR_EL2 register. We don't implement any of
the debug-related traps this register controls yet, so
currently it simply reads back as written.
Signed-off-by: NSergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1444383794-16767-1-git-send-email-serge.fdrv@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message; moved non-dummy definition from
debug_cp_reginfo to el2_cp_reginfo.]
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Added oslar_write function to OSLAR_EL1 sysreg, using a status variable
in ARMCPUState.cp15 struct (oslsr_el1). This variable is also linked
to the newly added read-only OSLSR_EL1 register.

Linux reads from this register during its suspend/resume procedure.
Signed-off-by: NDavorin Mista <davorin.mista@aggios.com>
[PMM: folded a long line and tweaked a comment]
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

It is incorrect to call arm_el_is_aa64() function for unimplemented EL.
This patch fixes several attempts to do so.
Signed-off-by: NSergey Sorokin <afarallax@yandex.ru>
[PMM: Reworked several of the comments to be more verbose.]
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

If any store instruction writes the code inside the same TB
after this store insn, the execution of the TB must be stopped
to execute new code correctly.
As described in ARMv8 manual D3.4.6 self-modifying code must do an
IC invalidation to be valid, and an ISB after it. So it's enough to end
the TB after ISB instruction on the code translation.
Also this TB break is necessary to take any pending interrupts immediately
after an ISB (as required by ARMv8 ARM D1.14.4).
Signed-off-by: NSergey Sorokin <afarallax@yandex.ru>
[PMM: tweaked commit message and comments slightly]
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NStefan Weil <sw@weilnetz.de>
Message-id: 1443213733-9807-1-git-send-email-sw@weilnetz.de
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

muldiv64() is used to convert microseconds into CPU ticks.

But it is not clear and not commented. This patch uses macro
to clearly identify what is used: time, CPU frequency and ticks.
For an elapsed time and a given frequency, we compute how many ticks
 we have.
Signed-off-by: NLaurent Vivier <lvivier@redhat.com>
Reviewed-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>

Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-9-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Break out mpidr_read_val() to allow future sharing of the
code that conditionally sets the M and U bits of MPIDR.

No functional changes.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-8-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-7-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Stage-2 translations, EL2 and EL3 regimes don't have the
EPD control.
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-6-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Stage-2 MMU translations do not have configurable TBI as
the top byte is always 0 (48-bit IPAs).
Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-5-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-4-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Signed-off-by: NEdgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1442135278-25281-3-git-send-email-edgar.iglesias@gmail.com
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
[PMM: fixed typo in comment]
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>