ppc4xx_i2c: Rewrite to model hardware more closely

Rewrite to make it closer to how real device works so that guest OS
drivers can access I2C devices. Previously this was only a hack to
allow U-Boot to get past accessing SPD EEPROMs but to support other
I2C devices and allow guests to access them we need to model real
device more properly.
Signed-off-by: NBALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: NCédric Le Goater <clg@kaod.org>
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>

hw/i2c/ppc4xx_i2c.c

@@ -34,16 +34,50 @@
 
 #define PPC4xx_I2C_MEM_SIZE 18
 
+enum {
+    IIC_MDBUF = 0,
+    /* IIC_SDBUF = 2, */
+    IIC_LMADR = 4,
+    IIC_HMADR,
+    IIC_CNTL,
+    IIC_MDCNTL,
+    IIC_STS,
+    IIC_EXTSTS,
+    IIC_LSADR,
+    IIC_HSADR,
+    IIC_CLKDIV,
+    IIC_INTRMSK,
+    IIC_XFRCNT,
+    IIC_XTCNTLSS,
+    IIC_DIRECTCNTL
+    /* IIC_INTR */
+};
+
 #define IIC_CNTL_PT         (1 << 0)
 #define IIC_CNTL_READ       (1 << 1)
 #define IIC_CNTL_CHT        (1 << 2)
 #define IIC_CNTL_RPST       (1 << 3)
+#define IIC_CNTL_AMD        (1 << 6)
+#define IIC_CNTL_HMT        (1 << 7)
+
+#define IIC_MDCNTL_EINT     (1 << 2)
+#define IIC_MDCNTL_ESM      (1 << 3)
+#define IIC_MDCNTL_FMDB     (1 << 6)
 
 #define IIC_STS_PT          (1 << 0)
+#define IIC_STS_IRQA        (1 << 1)
 #define IIC_STS_ERR         (1 << 2)
+#define IIC_STS_MDBF        (1 << 4)
 #define IIC_STS_MDBS        (1 << 5)
 
 #define IIC_EXTSTS_XFRA     (1 << 0)
+#define IIC_EXTSTS_BCS_FREE (4 << 4)
+#define IIC_EXTSTS_BCS_BUSY (5 << 4)
+
+#define IIC_INTRMSK_EIMTC   (1 << 0)
+#define IIC_INTRMSK_EITA    (1 << 1)
+#define IIC_INTRMSK_EIIC    (1 << 2)
+#define IIC_INTRMSK_EIHE    (1 << 3)
 
 #define IIC_XTCNTLSS_SRST   (1 << 0)
 
@@ -56,130 +90,83 @@ static void ppc4xx_i2c_reset(DeviceState *s)
 {
     PPC4xxI2CState *i2c = PPC4xx_I2C(s);
 
-    /* FIXME: Should also reset bus?
-     *if (s->address != ADDR_RESET) {
-     *    i2c_end_transfer(s->bus);
-     *}
-     */
-
-    i2c->mdata = 0;
-    i2c->lmadr = 0;
-    i2c->hmadr = 0;
+    i2c->mdidx = -1;
+    memset(i2c->mdata, 0, ARRAY_SIZE(i2c->mdata));
+    /* [hl][ms]addr are not affected by reset */
     i2c->cntl = 0;
     i2c->mdcntl = 0;
     i2c->sts = 0;
-    i2c->extsts = 0x8f;
-    i2c->lsadr = 0;
-    i2c->hsadr = 0;
+    i2c->extsts = IIC_EXTSTS_BCS_FREE;
     i2c->clkdiv = 0;
     i2c->intrmsk = 0;
     i2c->xfrcnt = 0;
     i2c->xtcntlss = 0;
-    i2c->directcntl = 0xf;
-}
-
-static inline bool ppc4xx_i2c_is_master(PPC4xxI2CState *i2c)
-{
-    return true;
+    i2c->directcntl = 0xf; /* all non-reserved bits set */
 }
 
 static uint64_t ppc4xx_i2c_readb(void *opaque, hwaddr addr, unsigned int size)
 {
     PPC4xxI2CState *i2c = PPC4xx_I2C(opaque);
     uint64_t ret;
+    int i;
 
     switch (addr) {
-    case 0:
-        ret = i2c->mdata;
-        if (ppc4xx_i2c_is_master(i2c)) {
+    case IIC_MDBUF:
+        if (i2c->mdidx < 0) {
             ret = 0xff;
-
-            if (!(i2c->sts & IIC_STS_MDBS)) {
-                qemu_log_mask(LOG_GUEST_ERROR, "[%s]%s: Trying to read "
-                              "without starting transfer\n",
-                              TYPE_PPC4xx_I2C, __func__);
-            } else {
-                int pending = (i2c->cntl >> 4) & 3;
-
-                /* get the next byte */
-                int byte = i2c_recv(i2c->bus);
-
-                if (byte < 0) {
-                    qemu_log_mask(LOG_GUEST_ERROR, "[%s]%s: read failed "
-                                  "for device 0x%02x\n", TYPE_PPC4xx_I2C,
-                                  __func__, i2c->lmadr);
-                    ret = 0xff;
-                } else {
-                    ret = byte;
-                    /* Raise interrupt if enabled */
-                    /*ppc4xx_i2c_raise_interrupt(i2c)*/;
-                }
-
-                if (!pending) {
-                    i2c->sts &= ~IIC_STS_MDBS;
-                    /*i2c_end_transfer(i2c->bus);*/
-                /*} else if (i2c->cntl & (IIC_CNTL_RPST | IIC_CNTL_CHT)) {*/
-                } else if (pending) {
-                    /* current smbus implementation doesn't like
-                       multibyte xfer repeated start */
-                    i2c_end_transfer(i2c->bus);
-                    if (i2c_start_transfer(i2c->bus, i2c->lmadr >> 1, 1)) {
-                        /* if non zero is returned, the adress is not valid */
-                        i2c->sts &= ~IIC_STS_PT;
-                        i2c->sts |= IIC_STS_ERR;
-                        i2c->extsts |= IIC_EXTSTS_XFRA;
-                    } else {
-                        /*i2c->sts |= IIC_STS_PT;*/
-                        i2c->sts |= IIC_STS_MDBS;
-                        i2c->sts &= ~IIC_STS_ERR;
-                        i2c->extsts = 0;
-                    }
-                }
-                pending--;
-                i2c->cntl = (i2c->cntl & 0xcf) | (pending << 4);
-            }
-        } else {
-            qemu_log_mask(LOG_UNIMP, "[%s]%s: slave mode not implemented\n",
-                          TYPE_PPC4xx_I2C, __func__);
+            break;
+        }
+        ret = i2c->mdata[0];
+        if (i2c->mdidx == 3) {
+            i2c->sts &= ~IIC_STS_MDBF;
+        } else if (i2c->mdidx == 0) {
+            i2c->sts &= ~IIC_STS_MDBS;
+        }
+        for (i = 0; i < i2c->mdidx; i++) {
+            i2c->mdata[i] = i2c->mdata[i + 1];
+        }
+        if (i2c->mdidx >= 0) {
+            i2c->mdidx--;
         }
         break;
-    case 4:
+    case IIC_LMADR:
         ret = i2c->lmadr;
         break;
-    case 5:
+    case IIC_HMADR:
         ret = i2c->hmadr;
         break;
-    case 6:
+    case IIC_CNTL:
         ret = i2c->cntl;
         break;
-    case 7:
+    case IIC_MDCNTL:
         ret = i2c->mdcntl;
         break;
-    case 8:
+    case IIC_STS:
         ret = i2c->sts;
         break;
-    case 9:
-        ret = i2c->extsts;
+    case IIC_EXTSTS:
+        ret = i2c_bus_busy(i2c->bus) ?
+              IIC_EXTSTS_BCS_BUSY : IIC_EXTSTS_BCS_FREE;
         break;
-    case 10:
+    case IIC_LSADR:
         ret = i2c->lsadr;
         break;
-    case 11:
+    case IIC_HSADR:
         ret = i2c->hsadr;
         break;
-    case 12:
+    case IIC_CLKDIV:
         ret = i2c->clkdiv;
         break;
-    case 13:
+    case IIC_INTRMSK:
         ret = i2c->intrmsk;
         break;
-    case 14:
+    case IIC_XFRCNT:
         ret = i2c->xfrcnt;
         break;
-    case 15:
+    case IIC_XTCNTLSS:
         ret = i2c->xtcntlss;
         break;
-    case 16:
+    case IIC_DIRECTCNTL:
         ret = i2c->directcntl;
         break;
     default:
@@ -202,99 +189,127 @@ static void ppc4xx_i2c_writeb(void *opaque, hwaddr addr, uint64_t value,
     PPC4xxI2CState *i2c = opaque;
 
     switch (addr) {
-    case 0:
-        i2c->mdata = value;
-        if (!i2c_bus_busy(i2c->bus)) {
-            /* assume we start a write transfer */
-            if (i2c_start_transfer(i2c->bus, i2c->lmadr >> 1, 0)) {
-                /* if non zero is returned, the adress is not valid */
-                i2c->sts &= ~IIC_STS_PT;
-                i2c->sts |= IIC_STS_ERR;
-                i2c->extsts |= IIC_EXTSTS_XFRA;
-            } else {
-                i2c->sts |= IIC_STS_PT;
-                i2c->sts &= ~IIC_STS_ERR;
-                i2c->extsts = 0;
-            }
+    case IIC_MDBUF:
+        if (i2c->mdidx >= 3) {
+            break;
         }
-        if (i2c_bus_busy(i2c->bus)) {
-            if (i2c_send(i2c->bus, i2c->mdata)) {
-                /* if the target return non zero then end the transfer */
-                i2c->sts &= ~IIC_STS_PT;
-                i2c->sts |= IIC_STS_ERR;
-                i2c->extsts |= IIC_EXTSTS_XFRA;
-                i2c_end_transfer(i2c->bus);
-            }
+        i2c->mdata[++i2c->mdidx] = value;
+        if (i2c->mdidx == 3) {
+            i2c->sts |= IIC_STS_MDBF;
+        } else if (i2c->mdidx == 0) {
+            i2c->sts |= IIC_STS_MDBS;
         }
         break;
-    case 4:
+    case IIC_LMADR:
         i2c->lmadr = value;
-        if (i2c_bus_busy(i2c->bus)) {
-            i2c_end_transfer(i2c->bus);
-        }
         break;
-    case 5:
+    case IIC_HMADR:
         i2c->hmadr = value;
         break;
-    case 6:
-        i2c->cntl = value;
-        if (i2c->cntl & IIC_CNTL_PT) {
-            if (i2c->cntl & IIC_CNTL_READ) {
-                if (i2c_bus_busy(i2c->bus)) {
-                    /* end previous transfer */
-                    i2c->sts &= ~IIC_STS_PT;
-                    i2c_end_transfer(i2c->bus);
+    case IIC_CNTL:
+        i2c->cntl = value & ~IIC_CNTL_PT;
+        if (value & IIC_CNTL_AMD) {
+            qemu_log_mask(LOG_UNIMP, "%s: only 7 bit addresses supported\n",
+                          __func__);
+        }
+        if (value & IIC_CNTL_HMT && i2c_bus_busy(i2c->bus)) {
+            i2c_end_transfer(i2c->bus);
+            if (i2c->mdcntl & IIC_MDCNTL_EINT &&
+                i2c->intrmsk & IIC_INTRMSK_EIHE) {
+                i2c->sts |= IIC_STS_IRQA;
+                qemu_irq_raise(i2c->irq);
+            }
+        } else if (value & IIC_CNTL_PT) {
+            int recv = (value & IIC_CNTL_READ) >> 1;
+            int tct = value >> 4 & 3;
+            int i;
+
+            if (recv && (i2c->lmadr >> 1) >= 0x50 && (i2c->lmadr >> 1) < 0x58) {
+                /* smbus emulation does not like multi byte reads w/o restart */
+                value |= IIC_CNTL_RPST;
+            }
+
+            for (i = 0; i <= tct; i++) {
+                if (!i2c_bus_busy(i2c->bus)) {
+                    i2c->extsts = IIC_EXTSTS_BCS_FREE;
+                    if (i2c_start_transfer(i2c->bus, i2c->lmadr >> 1, recv)) {
+                        i2c->sts |= IIC_STS_ERR;
+                        i2c->extsts |= IIC_EXTSTS_XFRA;
+                        break;
+                    } else {
+                        i2c->sts &= ~IIC_STS_ERR;
+                    }
                 }
-                if (i2c_start_transfer(i2c->bus, i2c->lmadr >> 1, 1)) {
-                    /* if non zero is returned, the adress is not valid */
-                    i2c->sts &= ~IIC_STS_PT;
+                if (!(i2c->sts & IIC_STS_ERR) &&
+                    i2c_send_recv(i2c->bus, &i2c->mdata[i], !recv)) {
                     i2c->sts |= IIC_STS_ERR;
                     i2c->extsts |= IIC_EXTSTS_XFRA;
-                } else {
-                    /*i2c->sts |= IIC_STS_PT;*/
-                    i2c->sts |= IIC_STS_MDBS;
-                    i2c->sts &= ~IIC_STS_ERR;
-                    i2c->extsts = 0;
+                    break;
+                }
+                if (value & IIC_CNTL_RPST || !(value & IIC_CNTL_CHT)) {
+                    i2c_end_transfer(i2c->bus);
                 }
-            } else {
-                /* we actually already did the write transfer... */
-                i2c->sts &= ~IIC_STS_PT;
+            }
+            i2c->xfrcnt = i;
+            i2c->mdidx = i - 1;
+            if (recv && i2c->mdidx >= 0) {
+                i2c->sts |= IIC_STS_MDBS;
+            }
+            if (recv && i2c->mdidx == 3) {
+                i2c->sts |= IIC_STS_MDBF;
+            }
+            if (i && i2c->mdcntl & IIC_MDCNTL_EINT &&
+                i2c->intrmsk & IIC_INTRMSK_EIMTC) {
+                i2c->sts |= IIC_STS_IRQA;
+                qemu_irq_raise(i2c->irq);
             }
         }
         break;
-    case 7:
-        i2c->mdcntl = value & 0xdf;
+    case IIC_MDCNTL:
+        i2c->mdcntl = value & 0x3d;
+        if (value & IIC_MDCNTL_ESM) {
+            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
+                          __func__);
+        }
+        if (value & IIC_MDCNTL_FMDB) {
+            i2c->mdidx = -1;
+            memset(i2c->mdata, 0, ARRAY_SIZE(i2c->mdata));
+            i2c->sts &= ~(IIC_STS_MDBF | IIC_STS_MDBS);
+        }
         break;
-    case 8:
-        i2c->sts &= ~(value & 0xa);
+    case IIC_STS:
+        i2c->sts &= ~(value & 0x0a);
+        if (value & IIC_STS_IRQA && i2c->mdcntl & IIC_MDCNTL_EINT) {
+            qemu_irq_lower(i2c->irq);
+        }
         break;
-    case 9:
+    case IIC_EXTSTS:
         i2c->extsts &= ~(value & 0x8f);
         break;
-    case 10:
+    case IIC_LSADR:
         i2c->lsadr = value;
         break;
-    case 11:
+    case IIC_HSADR:
         i2c->hsadr = value;
         break;
-    case 12:
+    case IIC_CLKDIV:
         i2c->clkdiv = value;
         break;
-    case 13:
+    case IIC_INTRMSK:
         i2c->intrmsk = value;
         break;
-    case 14:
+    case IIC_XFRCNT:
         i2c->xfrcnt = value & 0x77;
         break;
-    case 15:
+    case IIC_XTCNTLSS:
+        i2c->xtcntlss &= ~(value & 0xf0);
         if (value & IIC_XTCNTLSS_SRST) {
             /* Is it actually a full reset? U-Boot sets some regs before */
             ppc4xx_i2c_reset(DEVICE(i2c));
             break;
         }
-        i2c->xtcntlss = value;
         break;
-    case 16:
+    case IIC_DIRECTCNTL:
         i2c->directcntl = value & (IIC_DIRECTCNTL_SDAC & IIC_DIRECTCNTL_SCLC);
         i2c->directcntl |= (value & IIC_DIRECTCNTL_SCLC ? 1 : 0);
         bitbang_i2c_set(i2c->bitbang, BITBANG_I2C_SCL,

include/hw/i2c/ppc4xx_i2c.h

@@ -46,7 +46,8 @@ typedef struct PPC4xxI2CState {
     qemu_irq irq;
     MemoryRegion iomem;
     bitbang_i2c_interface *bitbang;
-    uint8_t mdata;
+    int mdidx;
+    uint8_t mdata[4];
     uint8_t lmadr;
     uint8_t hmadr;
     uint8_t cntl;