iotests: Make 150 use qemu-img map instead of du

The actual on-disk size of a file does not only depend on factors qemu
can control. Thus, we should not depend on this to determine whether a
file has indeed been fully allocated. Instead, use qemu-img map and hope
that if an area is referenced, it is indeed allocated, too.

Also, limit the supported image formats to raw and qcow2 because the
actual qemu-img map output may depend on the image format.
Signed-off-by: NMax Reitz <mreitz@redhat.com>
Tested-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

tests/qemu-iotests/150

@@ -38,65 +38,34 @@ trap "_cleanup; exit \$status" 0 1 2 3 15
 . ./common.rc
 . ./common.filter
 
-_supported_fmt generic
+_supported_fmt raw qcow2
 _supported_proto file
 _supported_os Linux
 
 
-on_disk_size()
-{
-    du "$@" | sed -e 's/\t\+.*//'
-}
-
-
 img_size=1048576
 
 
 echo
-echo '=== Comparing empty image against sparse conversion ==='
+echo '=== Mapping sparse conversion ==='
 echo
 
-_make_test_img $img_size
-
-empty_size=$(on_disk_size "$TEST_IMG")
-
-
 $QEMU_IMG_PROG convert -O "$IMGFMT" -S 512 \
     "json:{ 'driver': 'null-co', 'size': $img_size, 'read-zeroes': true }" \
     "$TEST_IMG"
 
-sparse_convert_size=$(on_disk_size "$TEST_IMG")
-
-
-if [ "$empty_size" -eq "$sparse_convert_size" ]; then
-    echo 'Equal image size'
-else
-    echo 'Different image size'
-fi
+$QEMU_IMG map "$TEST_IMG" | _filter_qemu_img_map
 
 
 echo
-echo '=== Comparing full image against non-sparse conversion ==='
+echo '=== Mapping non-sparse conversion ==='
 echo
 
-_make_test_img $img_size
-$QEMU_IO -c "write 0 $img_size" "$TEST_IMG" | _filter_qemu_io
-
-full_size=$(on_disk_size "$TEST_IMG")
-
-
 $QEMU_IMG convert -O "$IMGFMT" -S 0 \
     "json:{ 'driver': 'null-co', 'size': $img_size, 'read-zeroes': true }" \
     "$TEST_IMG"
 
-non_sparse_convert_size=$(on_disk_size "$TEST_IMG")
-
-
-if [ "$full_size" -eq "$non_sparse_convert_size" ]; then
-    echo 'Equal image size'
-else
-    echo 'Different image size'
-fi
+$QEMU_IMG map "$TEST_IMG" | _filter_qemu_img_map
 
 
 # success, all done

tests/qemu-iotests/150.out

 QA output created by 150
 
-=== Comparing empty image against sparse conversion ===
+=== Mapping sparse conversion ===
 
-Formatting 'TEST_DIR/t.IMGFMT', fmt=IMGFMT size=1048576
-Equal image size
+Offset          Length          File
 
-=== Comparing full image against non-sparse conversion ===
+=== Mapping non-sparse conversion ===
 
-Formatting 'TEST_DIR/t.IMGFMT', fmt=IMGFMT size=1048576
-wrote 1048576/1048576 bytes at offset 0
-1 MiB, X ops; XX:XX:XX.X (XXX YYY/sec and XXX ops/sec)
-Equal image size
+Offset          Length          File
+0               0x100000        TEST_DIR/t.IMGFMT
 *** done