eepro100.c

/*
 * QEMU i8255x (PRO100) emulation
 *
 * Copyright (c) 2006-2007 Stefan Weil
 *
 * Portions of the code are copies from grub / etherboot eepro100.c
 * and linux e100.c.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301  USA
 *
 * Tested features (i82559):
 *      PXE boot (i386) no valid link
 *      Linux networking (i386) ok
 *
 * Untested:
 *      non-i386 platforms
 *      Windows networking
 *
 * References:
 *
 * Intel 8255x 10/100 Mbps Ethernet Controller Family
 * Open Source Software Developer Manual
 */

#if defined(TARGET_I386)
# warning "PXE boot still not working!"
#endif

#include <assert.h>
#include <stddef.h>             /* offsetof */
#include "hw.h"
#include "pci.h"
#include "net.h"
#include "eeprom93xx.h"

/* Common declarations for all PCI devices. */

#define PCI_VENDOR_ID           0x00    /* 16 bits */
#define PCI_DEVICE_ID           0x02    /* 16 bits */
#define PCI_COMMAND             0x04    /* 16 bits */
#define PCI_STATUS              0x06    /* 16 bits */

#define PCI_REVISION_ID         0x08    /* 8 bits  */
#define PCI_CLASS_CODE          0x0b    /* 8 bits */
#define PCI_SUBCLASS_CODE       0x0a    /* 8 bits */
#define PCI_HEADER_TYPE         0x0e    /* 8 bits */

#define PCI_BASE_ADDRESS_0      0x10    /* 32 bits */
#define PCI_BASE_ADDRESS_1      0x14    /* 32 bits */
#define PCI_BASE_ADDRESS_2      0x18    /* 32 bits */
#define PCI_BASE_ADDRESS_3      0x1c    /* 32 bits */
#define PCI_BASE_ADDRESS_4      0x20    /* 32 bits */
#define PCI_BASE_ADDRESS_5      0x24    /* 32 bits */

#define PCI_CONFIG_8(offset, value) \
    (pci_conf[offset] = (value))
#define PCI_CONFIG_16(offset, value) \
    (*(uint16_t *)&pci_conf[offset] = cpu_to_le16(value))
#define PCI_CONFIG_32(offset, value) \
    (*(uint32_t *)&pci_conf[offset] = cpu_to_le32(value))

#define KiB 1024

/* debug EEPRO100 card */
//~ #define DEBUG_EEPRO100

#ifdef DEBUG_EEPRO100
#define logout(fmt, args...) fprintf(stderr, "EE100\t%-24s" fmt, __func__, ##args)
#else
#define logout(fmt, args...) ((void)0)
#endif

/* Set flags to 0 to disable debug output. */
#define MDI     0

#define TRACE(flag, command) ((flag) ? (command) : (void)0)

#define missing(text)       assert(!"feature is missing in this emulation: " text)

#define MAX_ETH_FRAME_SIZE 1514

/* This driver supports several different devices which are declared here. */
#define i82551          0x82551
#define i82557B         0x82557b
#define i82557C         0x82557c
#define i82558B         0x82558b
#define i82559C         0x82559c
#define i82559ER        0x82559e
#define i82562          0x82562

#define EEPROM_SIZE     64

#define PCI_MEM_SIZE            (4 * KiB)
#define PCI_IO_SIZE             64
#define PCI_FLASH_SIZE          (128 * KiB)

#define BIT(n) (1 << (n))
#define BITS(n, m) (((0xffffffffU << (31 - n)) >> (31 - n + m)) << m)

/* The SCB accepts the following controls for the Tx and Rx units: */
#define  CU_NOP         0x0000  /* No operation. */
#define  CU_START       0x0010  /* CU start. */
#define  CU_RESUME      0x0020  /* CU resume. */
#define  CU_STATSADDR   0x0040  /* Load dump counters address. */
#define  CU_SHOWSTATS   0x0050  /* Dump statistical counters. */
#define  CU_CMD_BASE    0x0060  /* Load CU base address. */
#define  CU_DUMPSTATS   0x0070  /* Dump and reset statistical counters. */
#define  CU_SRESUME     0x00a0  /* CU static resume. */

#define  RU_NOP         0x0000
#define  RX_START       0x0001
#define  RX_RESUME      0x0002
#define  RX_ABORT       0x0004
#define  RX_ADDR_LOAD   0x0006
#define  RX_RESUMENR    0x0007
#define INT_MASK        0x0100
#define DRVR_INT        0x0200  /* Driver generated interrupt. */

typedef unsigned char bool;

/* Offsets to the various registers.
   All accesses need not be longword aligned. */
enum speedo_offsets {
    SCBStatus = 0,
    SCBAck = 1,
    SCBCmd = 2,                 /* Rx/Command Unit command and status. */
    SCBIntmask = 3,
    SCBPointer = 4,             /* General purpose pointer. */
    SCBPort = 8,                /* Misc. commands and operands.  */
    SCBflash = 12, SCBeeprom = 14,      /* EEPROM and flash memory control. */
    SCBCtrlMDI = 16,            /* MDI interface control. */
    SCBEarlyRx = 20,            /* Early receive byte count. */
    SCBFlow = 24,
};

/* A speedo3 transmit buffer descriptor with two buffers... */
typedef struct {
    uint16_t status;
    uint16_t command;
    uint32_t link;              /* void * */
    uint32_t tx_desc_addr;      /* transmit buffer decsriptor array address. */
    uint16_t tcb_bytes;         /* transmit command block byte count (in lower 14 bits */
    uint8_t tx_threshold;       /* transmit threshold */
    uint8_t tbd_count;          /* TBD number */
    //~ /* This constitutes two "TBD" entries: hdr and data */
    //~ uint32_t tx_buf_addr0;  /* void *, header of frame to be transmitted.  */
    //~ int32_t  tx_buf_size0;  /* Length of Tx hdr. */
    //~ uint32_t tx_buf_addr1;  /* void *, data to be transmitted.  */
    //~ int32_t  tx_buf_size1;  /* Length of Tx data. */
} eepro100_tx_t;

/* Receive frame descriptor. */
typedef struct {
    int16_t status;
    uint16_t command;
    uint32_t link;              /* struct RxFD * */
    uint32_t rx_buf_addr;       /* void * */
    uint16_t count;
    uint16_t size;
    char packet[MAX_ETH_FRAME_SIZE + 4];
} eepro100_rx_t;

typedef struct {
    uint32_t tx_good_frames, tx_max_collisions, tx_late_collisions,
        tx_underruns, tx_lost_crs, tx_deferred, tx_single_collisions,
        tx_multiple_collisions, tx_total_collisions;
    uint32_t rx_good_frames, rx_crc_errors, rx_alignment_errors,
        rx_resource_errors, rx_overrun_errors, rx_cdt_errors,
        rx_short_frame_errors;
    uint32_t fc_xmt_pause, fc_rcv_pause, fc_rcv_unsupported;
    uint16_t xmt_tco_frames, rcv_tco_frames;
    uint32_t complete;
} eepro100_stats_t;

typedef enum {
    cu_idle = 0,
    cu_suspended = 1,
    cu_active = 2,
    cu_lpq_active = 2,
    cu_hqp_active = 3
} cu_state_t;

typedef enum {
    ru_idle = 0,
    ru_suspended = 1,
    ru_no_resources = 2,
    ru_ready = 4
} ru_state_t;

#if defined(__BIG_ENDIAN_BITFIELD)
#define X(a,b)	b,a
#else
#define X(a,b)	a,b
#endif

typedef struct {
#if 1
    uint8_t cmd;
    uint32_t start;
    uint32_t stop;
    uint8_t boundary;
    uint8_t tsr;
    uint8_t tpsr;
    uint16_t tcnt;
    uint16_t rcnt;
    uint32_t rsar;
    uint8_t rsr;
    uint8_t rxcr;
    uint8_t isr;
    uint8_t dcfg;
    uint8_t imr;
    uint8_t phys[6];            /* mac address */
    uint8_t curpag;
    uint8_t mult[8];            /* multicast mask array */
    int mmio_index;
    PCIDevice *pci_dev;
    VLANClientState *vc;
#endif
    uint8_t scb_stat;           /* SCB stat/ack byte */
    uint8_t int_stat;           /* PCI interrupt status */
    uint32_t region[3];         /* PCI region addresses */
    uint8_t macaddr[6];
    uint32_t statcounter[19];
    uint16_t mdimem[32];
    eeprom_t *eeprom;
    uint32_t device;            /* device variant */
    uint32_t pointer;
    /* (cu_base + cu_offset) address the next command block in the command block list. */
    uint32_t cu_base;           /* CU base address */
    uint32_t cu_offset;         /* CU address offset */
    /* (ru_base + ru_offset) address the RFD in the Receive Frame Area. */
    uint32_t ru_base;           /* RU base address */
    uint32_t ru_offset;         /* RU address offset */
    uint32_t statsaddr;         /* pointer to eepro100_stats_t */
    eepro100_stats_t statistics;        /* statistical counters */
#if 0
    uint16_t status;
#endif

    /* Configuration bytes. */
    uint8_t configuration[22];

    /* Data in mem is always in the byte order of the controller (le). */
    uint8_t mem[PCI_MEM_SIZE];
} EEPRO100State;

/* Default values for MDI (PHY) registers */
static const uint16_t eepro100_mdi_default[] = {
    /* MDI Registers 0 - 6, 7 */
    0x3000, 0x780d, 0x02a8, 0x0154, 0x05e1, 0x0000, 0x0000, 0x0000,
    /* MDI Registers 8 - 15 */
    0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
    /* MDI Registers 16 - 31 */
    0x0003, 0x0000, 0x0001, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
    0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
};

/* Readonly mask for MDI (PHY) registers */
static const uint16_t eepro100_mdi_mask[] = {
    0x0000, 0xffff, 0xffff, 0xffff, 0xc01f, 0xffff, 0xffff, 0x0000,
    0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
    0x0fff, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff,
    0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
};

#define POLYNOMIAL 0x04c11db6

/* From FreeBSD */
/* XXX: optimize */
static int compute_mcast_idx(const uint8_t * ep)
{
    uint32_t crc;
    int carry, i, j;
    uint8_t b;

    crc = 0xffffffff;
    for (i = 0; i < 6; i++) {
        b = *ep++;
        for (j = 0; j < 8; j++) {
            carry = ((crc & 0x80000000L) ? 1 : 0) ^ (b & 0x01);
            crc <<= 1;
            b >>= 1;
            if (carry)
                crc = ((crc ^ POLYNOMIAL) | carry);
        }
    }
    return (crc >> 26);
}

#if defined(DEBUG_EEPRO100)
static const char *nic_dump(const uint8_t * buf, unsigned size)
{
    static char dump[3 * 16 + 1];
    char *p = &dump[0];
    if (size > 16)
        size = 16;
    while (size-- > 0) {
        p += sprintf(p, " %02x", *buf++);
    }
    return dump;
}
#endif                          /* DEBUG_EEPRO100 */

enum scb_stat_ack {
    stat_ack_not_ours = 0x00,
    stat_ack_sw_gen = 0x04,
    stat_ack_rnr = 0x10,
    stat_ack_cu_idle = 0x20,
    stat_ack_frame_rx = 0x40,
    stat_ack_cu_cmd_done = 0x80,
    stat_ack_not_present = 0xFF,
    stat_ack_rx = (stat_ack_sw_gen | stat_ack_rnr | stat_ack_frame_rx),
    stat_ack_tx = (stat_ack_cu_idle | stat_ack_cu_cmd_done),
};

static void disable_interrupt(EEPRO100State * s)
{
    if (s->int_stat) {
        logout("interrupt disabled\n");
        qemu_irq_lower(s->pci_dev->irq[0]);
        s->int_stat = 0;
    }
}

static void enable_interrupt(EEPRO100State * s)
{
    if (!s->int_stat) {
        logout("interrupt enabled\n");
        qemu_irq_raise(s->pci_dev->irq[0]);
        s->int_stat = 1;
    }
}

static void eepro100_acknowledge(EEPRO100State * s)
{
    s->scb_stat &= ~s->mem[SCBAck];
    s->mem[SCBAck] = s->scb_stat;
    if (s->scb_stat == 0) {
        disable_interrupt(s);
    }
}

static void eepro100_interrupt(EEPRO100State * s, uint8_t stat)
{
    uint8_t mask = ~s->mem[SCBIntmask];
    s->mem[SCBAck] |= stat;
    stat = s->scb_stat = s->mem[SCBAck];
    stat &= (mask | 0x0f);
    //~ stat &= (~s->mem[SCBIntmask] | 0x0xf);
    if (stat && (mask & 0x01)) {
        /* SCB mask and SCB Bit M do not disable interrupt. */
        enable_interrupt(s);
    } else if (s->int_stat) {
        disable_interrupt(s);
    }
}

static void eepro100_cx_interrupt(EEPRO100State * s)
{
    /* CU completed action command. */
    /* Transmit not ok (82557 only, not in emulation). */
    eepro100_interrupt(s, 0x80);
}

static void eepro100_cna_interrupt(EEPRO100State * s)
{
    /* CU left the active state. */
    eepro100_interrupt(s, 0x20);
}

static void eepro100_fr_interrupt(EEPRO100State * s)
{
    /* RU received a complete frame. */
    eepro100_interrupt(s, 0x40);
}

#if 0
static void eepro100_rnr_interrupt(EEPRO100State * s)
{
    /* RU is not ready. */
    eepro100_interrupt(s, 0x10);
}
#endif

static void eepro100_mdi_interrupt(EEPRO100State * s)
{
    /* MDI completed read or write cycle. */
    eepro100_interrupt(s, 0x08);
}

static void eepro100_swi_interrupt(EEPRO100State * s)
{
    /* Software has requested an interrupt. */
    eepro100_interrupt(s, 0x04);
}

#if 0
static void eepro100_fcp_interrupt(EEPRO100State * s)
{
    /* Flow control pause interrupt (82558 and later). */
    eepro100_interrupt(s, 0x01);
}
#endif

static void pci_reset(EEPRO100State * s)
{
    uint32_t device = s->device;
    uint8_t *pci_conf = s->pci_dev->config;

    logout("%p\n", s);

    /* PCI Vendor ID */
    pci_config_set_vendor_id(pci_conf, PCI_VENDOR_ID_INTEL);
    /* PCI Device ID */
    pci_config_set_device_id(pci_conf, 0x1209);
    /* PCI Command */
    PCI_CONFIG_16(PCI_COMMAND, 0x0000);
    /* PCI Status */
    PCI_CONFIG_16(PCI_STATUS, 0x2800);
    /* PCI Revision ID */
    PCI_CONFIG_8(PCI_REVISION_ID, 0x08);
    /* PCI Class Code */
    PCI_CONFIG_8(0x09, 0x00);
    PCI_CONFIG_8(PCI_SUBCLASS_CODE, 0x00);      // ethernet network controller
    PCI_CONFIG_8(PCI_CLASS_CODE, 0x02); // network controller
    /* PCI Cache Line Size */
    /* check cache line size!!! */
    //~ PCI_CONFIG_8(0x0c, 0x00);
    /* PCI Latency Timer */
    PCI_CONFIG_8(0x0d, 0x20);   // latency timer = 32 clocks
    /* PCI Header Type */
    /* BIST (built-in self test) */
#if defined(TARGET_I386)
// !!! workaround for buggy bios
//~ #define PCI_ADDRESS_SPACE_MEM_PREFETCH 0
#endif
#if 0
    /* PCI Base Address Registers */
    /* CSR Memory Mapped Base Address */
    PCI_CONFIG_32(PCI_BASE_ADDRESS_0,
                  PCI_ADDRESS_SPACE_MEM | PCI_ADDRESS_SPACE_MEM_PREFETCH);
    /* CSR I/O Mapped Base Address */
    PCI_CONFIG_32(PCI_BASE_ADDRESS_1, PCI_ADDRESS_SPACE_IO);
#if 0
    /* Flash Memory Mapped Base Address */
    PCI_CONFIG_32(PCI_BASE_ADDRESS_2, 0xfffe0000 | PCI_ADDRESS_SPACE_MEM);
#endif
#endif
    /* Expansion ROM Base Address (depends on boot disable!!!) */
    PCI_CONFIG_32(0x30, 0x00000000);
    /* Capability Pointer */
    PCI_CONFIG_8(0x34, 0xdc);
    /* Interrupt Pin */
    PCI_CONFIG_8(0x3d, 1);      // interrupt pin 0
    /* Minimum Grant */
    PCI_CONFIG_8(0x3e, 0x08);
    /* Maximum Latency */
    PCI_CONFIG_8(0x3f, 0x18);
    /* Power Management Capabilities / Next Item Pointer / Capability ID */
    PCI_CONFIG_32(0xdc, 0x7e210001);

    switch (device) {
    case i82551:
        //~ PCI_CONFIG_16(PCI_DEVICE_ID, 0x1209);
        PCI_CONFIG_8(PCI_REVISION_ID, 0x0f);
        break;
    case i82557B:
        PCI_CONFIG_16(PCI_DEVICE_ID, 0x1229);
        PCI_CONFIG_8(PCI_REVISION_ID, 0x02);
        break;
    case i82557C:
        PCI_CONFIG_16(PCI_DEVICE_ID, 0x1229);
        PCI_CONFIG_8(PCI_REVISION_ID, 0x03);
        break;
    case i82558B:
        PCI_CONFIG_16(PCI_DEVICE_ID, 0x1229);
        PCI_CONFIG_16(PCI_STATUS, 0x2810);
        PCI_CONFIG_8(PCI_REVISION_ID, 0x05);
        break;
    case i82559C:
        PCI_CONFIG_16(PCI_DEVICE_ID, 0x1229);
        PCI_CONFIG_16(PCI_STATUS, 0x2810);
        //~ PCI_CONFIG_8(PCI_REVISION_ID, 0x08);
        break;
    case i82559ER:
        //~ PCI_CONFIG_16(PCI_DEVICE_ID, 0x1209);
        PCI_CONFIG_16(PCI_STATUS, 0x2810);
        PCI_CONFIG_8(PCI_REVISION_ID, 0x09);
        break;
    //~ PCI_CONFIG_16(PCI_DEVICE_ID, 0x1029);
    //~ PCI_CONFIG_16(PCI_DEVICE_ID, 0x1030);       /* 82559 InBusiness 10/100 */
    default:
        logout("Device %X is undefined!\n", device);
    }

    if (device == i82557C || device == i82558B || device == i82559C) {
        logout("Get device id and revision from EEPROM!!!\n");
    }
}

static void nic_selective_reset(EEPRO100State * s)
{
    size_t i;
    uint16_t *eeprom_contents = eeprom93xx_data(s->eeprom);
    //~ eeprom93xx_reset(s->eeprom);
    memcpy(eeprom_contents, s->macaddr, 6);
    eeprom_contents[0xa] = 0x4000;
    uint16_t sum = 0;
    for (i = 0; i < EEPROM_SIZE - 1; i++) {
        sum += eeprom_contents[i];
    }
    eeprom_contents[EEPROM_SIZE - 1] = 0xbaba - sum;

    memset(s->mem, 0, sizeof(s->mem));
    uint32_t val = BIT(21);
    memcpy(&s->mem[SCBCtrlMDI], &val, sizeof(val));

    assert(sizeof(s->mdimem) == sizeof(eepro100_mdi_default));
    memcpy(&s->mdimem[0], &eepro100_mdi_default[0], sizeof(s->mdimem));
}

static void nic_reset(void *opaque)
{
    EEPRO100State *s = (EEPRO100State *) opaque;
    logout("%p\n", s);
    static int first;
    if (!first) {
        first = 1;
    }
    nic_selective_reset(s);
}

#if defined(DEBUG_EEPRO100)
static const char *reg[PCI_IO_SIZE / 4] = {
    "Command/Status",
    "General Pointer",
    "Port",
    "EEPROM/Flash Control",
    "MDI Control",
    "Receive DMA Byte Count",
    "Flow control register",
    "General Status/Control"
};

static char *regname(uint32_t addr)
{
    static char buf[16];
    if (addr < PCI_IO_SIZE) {
        const char *r = reg[addr / 4];
        if (r != 0) {
            sprintf(buf, "%s+%u", r, addr % 4);
        } else {
            sprintf(buf, "0x%02x", addr);
        }
    } else {
        sprintf(buf, "??? 0x%08x", addr);
    }
    return buf;
}
#endif                          /* DEBUG_EEPRO100 */

#if 0
static uint16_t eepro100_read_status(EEPRO100State * s)
{
    uint16_t val = s->status;
    logout("val=0x%04x\n", val);
    return val;
}

static void eepro100_write_status(EEPRO100State * s, uint16_t val)
{
    logout("val=0x%04x\n", val);
    s->status = val;
}
#endif

/*****************************************************************************
 *
 * Command emulation.
 *
 ****************************************************************************/

#if 0
static uint16_t eepro100_read_command(EEPRO100State * s)
{
    uint16_t val = 0xffff;
    //~ logout("val=0x%04x\n", val);
    return val;
}
#endif

/* Commands that can be put in a command list entry. */
enum commands {
    CmdNOp = 0,
    CmdIASetup = 1,
    CmdConfigure = 2,
    CmdMulticastList = 3,
    CmdTx = 4,
    CmdTDR = 5,                 /* load microcode */
    CmdDump = 6,
    CmdDiagnose = 7,

    /* And some extra flags: */
    CmdSuspend = 0x4000,        /* Suspend after completion. */
    CmdIntr = 0x2000,           /* Interrupt after completion. */
    CmdTxFlex = 0x0008,         /* Use "Flexible mode" for CmdTx command. */
};

static cu_state_t get_cu_state(EEPRO100State * s)
{
    return ((s->mem[SCBStatus] >> 6) & 0x03);
}

static void set_cu_state(EEPRO100State * s, cu_state_t state)
{
    s->mem[SCBStatus] = (s->mem[SCBStatus] & 0x3f) + (state << 6);
}

static ru_state_t get_ru_state(EEPRO100State * s)
{
    return ((s->mem[SCBStatus] >> 2) & 0x0f);
}

static void set_ru_state(EEPRO100State * s, ru_state_t state)
{
    s->mem[SCBStatus] = (s->mem[SCBStatus] & 0xc3) + (state << 2);
}

static void dump_statistics(EEPRO100State * s)
{
    /* Dump statistical data. Most data is never changed by the emulation
     * and always 0, so we first just copy the whole block and then those
     * values which really matter.
     * Number of data should check configuration!!!
     */
    cpu_physical_memory_write(s->statsaddr, (uint8_t *) & s->statistics, 64);
    stl_phys(s->statsaddr + 0, s->statistics.tx_good_frames);
    stl_phys(s->statsaddr + 36, s->statistics.rx_good_frames);
    stl_phys(s->statsaddr + 48, s->statistics.rx_resource_errors);
    stl_phys(s->statsaddr + 60, s->statistics.rx_short_frame_errors);
    //~ stw_phys(s->statsaddr + 76, s->statistics.xmt_tco_frames);
    //~ stw_phys(s->statsaddr + 78, s->statistics.rcv_tco_frames);
    //~ missing("CU dump statistical counters");
}

static void eepro100_cu_command(EEPRO100State * s, uint8_t val)
{
    eepro100_tx_t tx;
    uint32_t cb_address;
    switch (val) {
    case CU_NOP:
        /* No operation. */
        break;
    case CU_START:
        if (get_cu_state(s) != cu_idle) {
            /* Intel documentation says that CU must be idle for the CU
             * start command. Intel driver for Linux also starts the CU
             * from suspended state. */
            logout("CU state is %u, should be %u\n", get_cu_state(s), cu_idle);
            //~ assert(!"wrong CU state");
        }
        set_cu_state(s, cu_active);
        s->cu_offset = s->pointer;
      next_command:
        cb_address = s->cu_base + s->cu_offset;
        cpu_physical_memory_read(cb_address, (uint8_t *) & tx, sizeof(tx));
        uint16_t status = le16_to_cpu(tx.status);
        uint16_t command = le16_to_cpu(tx.command);
        logout
            ("val=0x%02x (cu start), status=0x%04x, command=0x%04x, link=0x%08x\n",
             val, status, command, tx.link);
        bool bit_el = ((command & 0x8000) != 0);
        bool bit_s = ((command & 0x4000) != 0);
        bool bit_i = ((command & 0x2000) != 0);
        bool bit_nc = ((command & 0x0010) != 0);
        //~ bool bit_sf = ((command & 0x0008) != 0);
        uint16_t cmd = command & 0x0007;
        s->cu_offset = le32_to_cpu(tx.link);
        switch (cmd) {
        case CmdNOp:
            /* Do nothing. */
            break;
        case CmdIASetup:
            cpu_physical_memory_read(cb_address + 8, &s->macaddr[0], 6);
            logout("macaddr: %s\n", nic_dump(&s->macaddr[0], 6));
            break;
        case CmdConfigure:
            cpu_physical_memory_read(cb_address + 8, &s->configuration[0],
                                     sizeof(s->configuration));
            logout("configuration: %s\n", nic_dump(&s->configuration[0], 16));
            break;
        case CmdMulticastList:
            //~ missing("multicast list");
            break;
        case CmdTx:
            (void)0;
            uint32_t tbd_array = le32_to_cpu(tx.tx_desc_addr);
            uint16_t tcb_bytes = (le16_to_cpu(tx.tcb_bytes) & 0x3fff);
            logout
                ("transmit, TBD array address 0x%08x, TCB byte count 0x%04x, TBD count %u\n",
                 tbd_array, tcb_bytes, tx.tbd_count);
            assert(!bit_nc);
            //~ assert(!bit_sf);
            assert(tcb_bytes <= 2600);
            /* Next assertion fails for local configuration. */
            //~ assert((tcb_bytes > 0) || (tbd_array != 0xffffffff));
            if (!((tcb_bytes > 0) || (tbd_array != 0xffffffff))) {
                logout
                    ("illegal values of TBD array address and TCB byte count!\n");
            }
            uint8_t buf[MAX_ETH_FRAME_SIZE + 4];
            uint16_t size = 0;
            uint32_t tbd_address = cb_address + 0x10;
            assert(tcb_bytes <= sizeof(buf));
            while (size < tcb_bytes) {
                uint32_t tx_buffer_address = ldl_phys(tbd_address);
                uint16_t tx_buffer_size = lduw_phys(tbd_address + 4);
                //~ uint16_t tx_buffer_el = lduw_phys(tbd_address + 6);
                tbd_address += 8;
                logout
                    ("TBD (simplified mode): buffer address 0x%08x, size 0x%04x\n",
                     tx_buffer_address, tx_buffer_size);
                cpu_physical_memory_read(tx_buffer_address, &buf[size],
                                         tx_buffer_size);
                size += tx_buffer_size;
            }
            if (tbd_array == 0xffffffff) {
                /* Simplified mode. Was already handled by code above. */
            } else {
                /* Flexible mode. */
                uint8_t tbd_count = 0;
                if (!(s->configuration[6] & BIT(4))) {
                    /* Extended TCB. */
                    assert(tcb_bytes == 0);
                    for (; tbd_count < 2; tbd_count++) {
                        uint32_t tx_buffer_address = ldl_phys(tbd_address);
                        uint16_t tx_buffer_size = lduw_phys(tbd_address + 4);
                        uint16_t tx_buffer_el = lduw_phys(tbd_address + 6);
                        tbd_address += 8;
                        logout
                            ("TBD (extended mode): buffer address 0x%08x, size 0x%04x\n",
                             tx_buffer_address, tx_buffer_size);
                        cpu_physical_memory_read(tx_buffer_address, &buf[size],
                                                 tx_buffer_size);
                        size += tx_buffer_size;
                        if (tx_buffer_el & 1) {
                            break;
                        }
                    }
                }
                tbd_address = tbd_array;
                for (; tbd_count < tx.tbd_count; tbd_count++) {
                    uint32_t tx_buffer_address = ldl_phys(tbd_address);
                    uint16_t tx_buffer_size = lduw_phys(tbd_address + 4);
                    uint16_t tx_buffer_el = lduw_phys(tbd_address + 6);
                    tbd_address += 8;
                    logout
                        ("TBD (flexible mode): buffer address 0x%08x, size 0x%04x\n",
                         tx_buffer_address, tx_buffer_size);
                    cpu_physical_memory_read(tx_buffer_address, &buf[size],
                                             tx_buffer_size);
                    size += tx_buffer_size;
                    if (tx_buffer_el & 1) {
                        break;
                    }
                }
            }
            qemu_send_packet(s->vc, buf, size);
            s->statistics.tx_good_frames++;
            /* Transmit with bad status would raise an CX/TNO interrupt.
             * (82557 only). Emulation never has bad status. */
            //~ eepro100_cx_interrupt(s);
            break;
        case CmdTDR:
            logout("load microcode\n");
            /* Starting with offset 8, the command contains
             * 64 dwords microcode which we just ignore here. */
            break;
        default:
            missing("undefined command");
        }
        /* Write new status (success). */
        stw_phys(cb_address, status | 0x8000 | 0x2000);
        if (bit_i) {
            /* CU completed action. */
            eepro100_cx_interrupt(s);
        }
        if (bit_el) {
            /* CU becomes idle. */
            set_cu_state(s, cu_idle);
            eepro100_cna_interrupt(s);
        } else if (bit_s) {
            /* CU becomes suspended. */
            set_cu_state(s, cu_suspended);
            eepro100_cna_interrupt(s);
        } else {
            /* More entries in list. */
            logout("CU list with at least one more entry\n");
            goto next_command;
        }
        logout("CU list empty\n");
        /* List is empty. Now CU is idle or suspended. */
        break;
    case CU_RESUME:
        if (get_cu_state(s) != cu_suspended) {
            logout("bad CU resume from CU state %u\n", get_cu_state(s));
            /* Workaround for bad Linux eepro100 driver which resumes
             * from idle state. */
            //~ missing("cu resume");
            set_cu_state(s, cu_suspended);
        }
        if (get_cu_state(s) == cu_suspended) {
            logout("CU resuming\n");
            set_cu_state(s, cu_active);
            goto next_command;
        }
        break;
    case CU_STATSADDR:
        /* Load dump counters address. */
        s->statsaddr = s->pointer;
        logout("val=0x%02x (status address)\n", val);
        break;
    case CU_SHOWSTATS:
        /* Dump statistical counters. */
        dump_statistics(s);
        break;
    case CU_CMD_BASE:
        /* Load CU base. */
        logout("val=0x%02x (CU base address)\n", val);
        s->cu_base = s->pointer;
        break;
    case CU_DUMPSTATS:
        /* Dump and reset statistical counters. */
        dump_statistics(s);
        memset(&s->statistics, 0, sizeof(s->statistics));
        break;
    case CU_SRESUME:
        /* CU static resume. */
        missing("CU static resume");
        break;
    default:
        missing("Undefined CU command");
    }
}

static void eepro100_ru_command(EEPRO100State * s, uint8_t val)
{
    switch (val) {
    case RU_NOP:
        /* No operation. */
        break;
    case RX_START:
        /* RU start. */
        if (get_ru_state(s) != ru_idle) {
            logout("RU state is %u, should be %u\n", get_ru_state(s), ru_idle);
            //~ assert(!"wrong RU state");
        }
        set_ru_state(s, ru_ready);
        s->ru_offset = s->pointer;
        logout("val=0x%02x (rx start)\n", val);
        break;
    case RX_RESUME:
        /* Restart RU. */
        if (get_ru_state(s) != ru_suspended) {
            logout("RU state is %u, should be %u\n", get_ru_state(s),
                   ru_suspended);
            //~ assert(!"wrong RU state");
        }
        set_ru_state(s, ru_ready);
        break;
    case RX_ADDR_LOAD:
        /* Load RU base. */
        logout("val=0x%02x (RU base address)\n", val);
        s->ru_base = s->pointer;
        break;
    default:
        logout("val=0x%02x (undefined RU command)\n", val);
        missing("Undefined SU command");
    }
}

static void eepro100_write_command(EEPRO100State * s, uint8_t val)
{
    eepro100_ru_command(s, val & 0x0f);
    eepro100_cu_command(s, val & 0xf0);
    if ((val) == 0) {
        logout("val=0x%02x\n", val);
    }
    /* Clear command byte after command was accepted. */
    s->mem[SCBCmd] = 0;
}

/*****************************************************************************
 *
 * EEPROM emulation.
 *
 ****************************************************************************/

#define EEPROM_CS       0x02
#define EEPROM_SK       0x01
#define EEPROM_DI       0x04
#define EEPROM_DO       0x08

static uint16_t eepro100_read_eeprom(EEPRO100State * s)
{
    uint16_t val;
    memcpy(&val, &s->mem[SCBeeprom], sizeof(val));
    if (eeprom93xx_read(s->eeprom)) {
        val |= EEPROM_DO;
    } else {
        val &= ~EEPROM_DO;
    }
    return val;
}

static void eepro100_write_eeprom(eeprom_t * eeprom, uint8_t val)
{
    logout("write val=0x%02x\n", val);

    /* mask unwriteable bits */
    //~ val = SET_MASKED(val, 0x31, eeprom->value);

    int eecs = ((val & EEPROM_CS) != 0);
    int eesk = ((val & EEPROM_SK) != 0);
    int eedi = ((val & EEPROM_DI) != 0);
    eeprom93xx_write(eeprom, eecs, eesk, eedi);
}

static void eepro100_write_pointer(EEPRO100State * s, uint32_t val)
{
    s->pointer = le32_to_cpu(val);
    logout("val=0x%08x\n", val);
}

/*****************************************************************************
 *
 * MDI emulation.
 *
 ****************************************************************************/

#if defined(DEBUG_EEPRO100)
static const char *mdi_op_name[] = {
    "opcode 0",
    "write",
    "read",
    "opcode 3"
};

static const char *mdi_reg_name[] = {
    "Control",
    "Status",
    "PHY Identification (Word 1)",
    "PHY Identification (Word 2)",
    "Auto-Negotiation Advertisement",
    "Auto-Negotiation Link Partner Ability",
    "Auto-Negotiation Expansion"
};
#endif                          /* DEBUG_EEPRO100 */

static uint32_t eepro100_read_mdi(EEPRO100State * s)
{
    uint32_t val;
    memcpy(&val, &s->mem[0x10], sizeof(val));

#ifdef DEBUG_EEPRO100
    uint8_t raiseint = (val & BIT(29)) >> 29;
    uint8_t opcode = (val & BITS(27, 26)) >> 26;
    uint8_t phy = (val & BITS(25, 21)) >> 21;
    uint8_t reg = (val & BITS(20, 16)) >> 16;
    uint16_t data = (val & BITS(15, 0));
#endif
    /* Emulation takes no time to finish MDI transaction. */
    val |= BIT(28);
    TRACE(MDI, logout("val=0x%08x (int=%u, %s, phy=%u, %s, data=0x%04x\n",
                      val, raiseint, mdi_op_name[opcode], phy,
                      mdi_reg_name[reg], data));
    return val;
}

//~ #define BITS(val, upper, lower) (val & ???)
static void eepro100_write_mdi(EEPRO100State * s, uint32_t val)
{
    uint8_t raiseint = (val & BIT(29)) >> 29;
    uint8_t opcode = (val & BITS(27, 26)) >> 26;
    uint8_t phy = (val & BITS(25, 21)) >> 21;
    uint8_t reg = (val & BITS(20, 16)) >> 16;
    uint16_t data = (val & BITS(15, 0));
    if (phy != 1) {
        /* Unsupported PHY address. */
        //~ logout("phy must be 1 but is %u\n", phy);
        data = 0;
    } else if (opcode != 1 && opcode != 2) {
        /* Unsupported opcode. */
        logout("opcode must be 1 or 2 but is %u\n", opcode);
        data = 0;
    } else if (reg > 6) {
        /* Unsupported register. */
        logout("register must be 0...6 but is %u\n", reg);
        data = 0;
    } else {
        TRACE(MDI, logout("val=0x%08x (int=%u, %s, phy=%u, %s, data=0x%04x\n",
                          val, raiseint, mdi_op_name[opcode], phy,
                          mdi_reg_name[reg], data));
        if (opcode == 1) {
            /* MDI write */
            switch (reg) {
            case 0:            /* Control Register */
                if (data & 0x8000) {
                    /* Reset status and control registers to default. */
                    s->mdimem[0] = eepro100_mdi_default[0];
                    s->mdimem[1] = eepro100_mdi_default[1];
                    data = s->mdimem[reg];
                } else {
                    /* Restart Auto Configuration = Normal Operation */
                    data &= ~0x0200;
                }
                break;
            case 1:            /* Status Register */
                missing("not writable");
                data = s->mdimem[reg];
                break;
            case 2:            /* PHY Identification Register (Word 1) */
            case 3:            /* PHY Identification Register (Word 2) */
                missing("not implemented");
                break;
            case 4:            /* Auto-Negotiation Advertisement Register */
            case 5:            /* Auto-Negotiation Link Partner Ability Register */
                break;
            case 6:            /* Auto-Negotiation Expansion Register */
            default:
                missing("not implemented");
            }
            s->mdimem[reg] = data;
        } else if (opcode == 2) {
            /* MDI read */
            switch (reg) {
            case 0:            /* Control Register */
                if (data & 0x8000) {
                    /* Reset status and control registers to default. */
                    s->mdimem[0] = eepro100_mdi_default[0];
                    s->mdimem[1] = eepro100_mdi_default[1];
                }
                break;
            case 1:            /* Status Register */
                s->mdimem[reg] |= 0x0020;
                break;
            case 2:            /* PHY Identification Register (Word 1) */
            case 3:            /* PHY Identification Register (Word 2) */
            case 4:            /* Auto-Negotiation Advertisement Register */
                break;
            case 5:            /* Auto-Negotiation Link Partner Ability Register */
                s->mdimem[reg] = 0x41fe;
                break;
            case 6:            /* Auto-Negotiation Expansion Register */
                s->mdimem[reg] = 0x0001;
                break;
            }
            data = s->mdimem[reg];
        }
        /* Emulation takes no time to finish MDI transaction.
         * Set MDI bit in SCB status register. */
        s->mem[SCBAck] |= 0x08;
        val |= BIT(28);
        if (raiseint) {
            eepro100_mdi_interrupt(s);
        }
    }
    val = (val & 0xffff0000) + data;
    memcpy(&s->mem[0x10], &val, sizeof(val));
}

/*****************************************************************************
 *
 * Port emulation.
 *
 ****************************************************************************/

#define PORT_SOFTWARE_RESET     0
#define PORT_SELFTEST           1
#define PORT_SELECTIVE_RESET    2
#define PORT_DUMP               3
#define PORT_SELECTION_MASK     3

typedef struct {
    uint32_t st_sign;           /* Self Test Signature */
    uint32_t st_result;         /* Self Test Results */
} eepro100_selftest_t;

static uint32_t eepro100_read_port(EEPRO100State * s)
{
    return 0;
}

static void eepro100_write_port(EEPRO100State * s, uint32_t val)
{
    val = le32_to_cpu(val);
    uint32_t address = (val & ~PORT_SELECTION_MASK);
    uint8_t selection = (val & PORT_SELECTION_MASK);
    switch (selection) {
    case PORT_SOFTWARE_RESET:
        nic_reset(s);
        break;
    case PORT_SELFTEST:
        logout("selftest address=0x%08x\n", address);
        eepro100_selftest_t data;
        cpu_physical_memory_read(address, (uint8_t *) & data, sizeof(data));
        data.st_sign = 0xffffffff;
        data.st_result = 0;
        cpu_physical_memory_write(address, (uint8_t *) & data, sizeof(data));
        break;
    case PORT_SELECTIVE_RESET:
        logout("selective reset, selftest address=0x%08x\n", address);
        nic_selective_reset(s);
        break;
    default:
        logout("val=0x%08x\n", val);
        missing("unknown port selection");
    }
}

/*****************************************************************************
 *
 * General hardware emulation.
 *
 ****************************************************************************/

static uint8_t eepro100_read1(EEPRO100State * s, uint32_t addr)
{
    uint8_t val;
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&val, &s->mem[addr], sizeof(val));
    }

    switch (addr) {
    case SCBStatus:
        //~ val = eepro100_read_status(s);
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case SCBAck:
        //~ val = eepro100_read_status(s);
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case SCBCmd:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        //~ val = eepro100_read_command(s);
        break;
    case SCBIntmask:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case SCBPort + 3:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case SCBeeprom:
        val = eepro100_read_eeprom(s);
        break;
    case 0x1b:                 /* PMDR (power management driver register) */
        val = 0;
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case 0x1d:                 /* general status register */
        /* 100 Mbps full duplex, valid link */
        val = 0x07;
        logout("addr=General Status val=%02x\n", val);
        break;
    default:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        missing("unknown byte read");
    }
    return val;
}

static uint16_t eepro100_read2(EEPRO100State * s, uint32_t addr)
{
    uint16_t val;
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&val, &s->mem[addr], sizeof(val));
    }

    logout("addr=%s val=0x%04x\n", regname(addr), val);

    switch (addr) {
    case SCBStatus:
        //~ val = eepro100_read_status(s);
        break;
    case SCBeeprom:
        val = eepro100_read_eeprom(s);
        break;
    default:
        logout("addr=%s val=0x%04x\n", regname(addr), val);
        missing("unknown word read");
    }
    return val;
}

static uint32_t eepro100_read4(EEPRO100State * s, uint32_t addr)
{
    uint32_t val;
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&val, &s->mem[addr], sizeof(val));
    }

    switch (addr) {
    case SCBStatus:
        //~ val = eepro100_read_status(s);
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        break;
    case SCBPointer:
        //~ val = eepro100_read_pointer(s);
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        break;
    case SCBPort:
        val = eepro100_read_port(s);
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        break;
    case SCBCtrlMDI:
        val = eepro100_read_mdi(s);
        break;
    default:
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        missing("unknown longword read");
    }
    return val;
}

static void eepro100_write1(EEPRO100State * s, uint32_t addr, uint8_t val)
{
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&s->mem[addr], &val, sizeof(val));
    }

    logout("addr=%s val=0x%02x\n", regname(addr), val);

    switch (addr) {
    case SCBStatus:
        //~ eepro100_write_status(s, val);
        break;
    case SCBAck:
        eepro100_acknowledge(s);
        break;
    case SCBCmd:
        eepro100_write_command(s, val);
        break;
    case SCBIntmask:
        if (val & BIT(1)) {
            eepro100_swi_interrupt(s);
        }
        eepro100_interrupt(s, 0);
        break;
    case SCBPort + 3:
    case SCBFlow:
    case SCBFlow + 1:
    case SCBFlow + 2:
    case SCBFlow + 3:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        break;
    case SCBeeprom:
        eepro100_write_eeprom(s->eeprom, val);
        break;
    default:
        logout("addr=%s val=0x%02x\n", regname(addr), val);
        missing("unknown byte write");
    }
}

static void eepro100_write2(EEPRO100State * s, uint32_t addr, uint16_t val)
{
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&s->mem[addr], &val, sizeof(val));
    }

    logout("addr=%s val=0x%04x\n", regname(addr), val);

    switch (addr) {
    case SCBStatus:
        //~ eepro100_write_status(s, val);
        eepro100_acknowledge(s);
        break;
    case SCBCmd:
        eepro100_write_command(s, val);
        eepro100_write1(s, SCBIntmask, val >> 8);
        break;
    case SCBeeprom:
        eepro100_write_eeprom(s->eeprom, val);
        break;
    default:
        logout("addr=%s val=0x%04x\n", regname(addr), val);
        missing("unknown word write");
    }
}

static void eepro100_write4(EEPRO100State * s, uint32_t addr, uint32_t val)
{
    if (addr <= sizeof(s->mem) - sizeof(val)) {
        memcpy(&s->mem[addr], &val, sizeof(val));
    }

    switch (addr) {
    case SCBPointer:
        eepro100_write_pointer(s, val);
        break;
    case SCBPort:
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        eepro100_write_port(s, val);
        break;
    case SCBCtrlMDI:
        eepro100_write_mdi(s, val);
        break;
    default:
        logout("addr=%s val=0x%08x\n", regname(addr), val);
        missing("unknown longword write");
    }
}

static uint32_t ioport_read1(void *opaque, uint32_t addr)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s\n", regname(addr));
    return eepro100_read1(s, addr - s->region[1]);
}

static uint32_t ioport_read2(void *opaque, uint32_t addr)
{
    EEPRO100State *s = opaque;
    return eepro100_read2(s, addr - s->region[1]);
}

static uint32_t ioport_read4(void *opaque, uint32_t addr)
{
    EEPRO100State *s = opaque;
    return eepro100_read4(s, addr - s->region[1]);
}

static void ioport_write1(void *opaque, uint32_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s val=0x%02x\n", regname(addr), val);
    eepro100_write1(s, addr - s->region[1], val);
}

static void ioport_write2(void *opaque, uint32_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    eepro100_write2(s, addr - s->region[1], val);
}

static void ioport_write4(void *opaque, uint32_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    eepro100_write4(s, addr - s->region[1], val);
}

/***********************************************************/
/* PCI EEPRO100 definitions */

typedef struct PCIEEPRO100State {
    PCIDevice dev;
    EEPRO100State eepro100;
} PCIEEPRO100State;

static void pci_map(PCIDevice * pci_dev, int region_num,
                    uint32_t addr, uint32_t size, int type)
{
    PCIEEPRO100State *d = (PCIEEPRO100State *) pci_dev;
    EEPRO100State *s = &d->eepro100;

    logout("region %d, addr=0x%08x, size=0x%08x, type=%d\n",
           region_num, addr, size, type);

    assert(region_num == 1);
    register_ioport_write(addr, size, 1, ioport_write1, s);
    register_ioport_read(addr, size, 1, ioport_read1, s);
    register_ioport_write(addr, size, 2, ioport_write2, s);
    register_ioport_read(addr, size, 2, ioport_read2, s);
    register_ioport_write(addr, size, 4, ioport_write4, s);
    register_ioport_read(addr, size, 4, ioport_read4, s);

    s->region[region_num] = addr;
}

static void pci_mmio_writeb(void *opaque, target_phys_addr_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s val=0x%02x\n", regname(addr), val);
    eepro100_write1(s, addr, val);
}

static void pci_mmio_writew(void *opaque, target_phys_addr_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s val=0x%02x\n", regname(addr), val);
    eepro100_write2(s, addr, val);
}

static void pci_mmio_writel(void *opaque, target_phys_addr_t addr, uint32_t val)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s val=0x%02x\n", regname(addr), val);
    eepro100_write4(s, addr, val);
}

static uint32_t pci_mmio_readb(void *opaque, target_phys_addr_t addr)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s\n", regname(addr));
    return eepro100_read1(s, addr);
}

static uint32_t pci_mmio_readw(void *opaque, target_phys_addr_t addr)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s\n", regname(addr));
    return eepro100_read2(s, addr);
}

static uint32_t pci_mmio_readl(void *opaque, target_phys_addr_t addr)
{
    EEPRO100State *s = opaque;
    //~ logout("addr=%s\n", regname(addr));
    return eepro100_read4(s, addr);
}

static CPUWriteMemoryFunc *pci_mmio_write[] = {
    pci_mmio_writeb,
    pci_mmio_writew,
    pci_mmio_writel
};

static CPUReadMemoryFunc *pci_mmio_read[] = {
    pci_mmio_readb,
    pci_mmio_readw,
    pci_mmio_readl
};

static void pci_mmio_map(PCIDevice * pci_dev, int region_num,
                         uint32_t addr, uint32_t size, int type)
{
    PCIEEPRO100State *d = (PCIEEPRO100State *) pci_dev;

    logout("region %d, addr=0x%08x, size=0x%08x, type=%d\n",
           region_num, addr, size, type);

    if (region_num == 0) {
        /* Map control / status registers. */
        cpu_register_physical_memory(addr, size, d->eepro100.mmio_index);
        d->eepro100.region[region_num] = addr;
    }
}

static int nic_can_receive(void *opaque)
{
    EEPRO100State *s = opaque;
    logout("%p\n", s);
    return get_ru_state(s) == ru_ready;
    //~ return !eepro100_buffer_full(s);
}

#define MIN_BUF_SIZE 60

static void nic_receive(void *opaque, const uint8_t * buf, int size)
{
    /* TODO:
     * - Magic packets should set bit 30 in power management driver register.
     * - Interesting packets should set bit 29 in power management driver register.
     */
    EEPRO100State *s = opaque;
    uint16_t rfd_status = 0xa000;
    static const uint8_t broadcast_macaddr[6] =
        { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };

    /* TODO: check multiple IA bit. */
    assert(!(s->configuration[20] & BIT(6)));

    if (s->configuration[8] & 0x80) {
        /* CSMA is disabled. */
        logout("%p received while CSMA is disabled\n", s);
        return;
    } else if (size < 64 && (s->configuration[7] & 1)) {
        /* Short frame and configuration byte 7/0 (discard short receive) set:
         * Short frame is discarded */
        logout("%p received short frame (%d byte)\n", s, size);
        s->statistics.rx_short_frame_errors++;
        //~ return;
    } else if ((size > MAX_ETH_FRAME_SIZE + 4) && !(s->configuration[18] & 8)) {
        /* Long frame and configuration byte 18/3 (long receive ok) not set:
         * Long frames are discarded. */
        logout("%p received long frame (%d byte), ignored\n", s, size);
        return;
    } else if (memcmp(buf, s->macaddr, 6) == 0) {       // !!!
        /* Frame matches individual address. */
        /* TODO: check configuration byte 15/4 (ignore U/L). */
        logout("%p received frame for me, len=%d\n", s, size);
    } else if (memcmp(buf, broadcast_macaddr, 6) == 0) {
        /* Broadcast frame. */
        logout("%p received broadcast, len=%d\n", s, size);
        rfd_status |= 0x0002;
    } else if (buf[0] & 0x01) { // !!!
        /* Multicast frame. */
        logout("%p received multicast, len=%d\n", s, size);
        /* TODO: check multicast all bit. */
        assert(!(s->configuration[21] & BIT(3)));
        int mcast_idx = compute_mcast_idx(buf);
        if (!(s->mult[mcast_idx >> 3] & (1 << (mcast_idx & 7)))) {
            return;
        }
        rfd_status |= 0x0002;
    } else if (s->configuration[15] & 1) {
        /* Promiscuous: receive all. */
        logout("%p received frame in promiscuous mode, len=%d\n", s, size);
        rfd_status |= 0x0004;
    } else {
        logout("%p received frame, ignored, len=%d,%s\n", s, size,
               nic_dump(buf, size));
        return;
    }

    if (get_ru_state(s) != ru_ready) {
        /* No ressources available. */
        logout("no ressources, state=%u\n", get_ru_state(s));
        s->statistics.rx_resource_errors++;
        //~ assert(!"no ressources");
        return;
    }
    //~ !!!
//~ $3 = {status = 0x0, command = 0xc000, link = 0x2d220, rx_buf_addr = 0x207dc, count = 0x0, size = 0x5f8, packet = {0x0 <repeats 1518 times>}}
    eepro100_rx_t rx;
    cpu_physical_memory_read(s->ru_base + s->ru_offset, (uint8_t *) & rx,
                             offsetof(eepro100_rx_t, packet));
    uint16_t rfd_command = le16_to_cpu(rx.command);
    uint16_t rfd_size = le16_to_cpu(rx.size);
    assert(size <= rfd_size);
    if (size < 64) {
        rfd_status |= 0x0080;
    }
    logout("command 0x%04x, link 0x%08x, addr 0x%08x, size %u\n", rfd_command,
           rx.link, rx.rx_buf_addr, rfd_size);
    stw_phys(s->ru_base + s->ru_offset + offsetof(eepro100_rx_t, status),
             rfd_status);
    stw_phys(s->ru_base + s->ru_offset + offsetof(eepro100_rx_t, count), size);
    /* Early receive interrupt not supported. */
    //~ eepro100_er_interrupt(s);
    /* Receive CRC Transfer not supported. */
    assert(!(s->configuration[18] & 4));
    /* TODO: check stripping enable bit. */
    //~ assert(!(s->configuration[17] & 1));
    cpu_physical_memory_write(s->ru_base + s->ru_offset +
                              offsetof(eepro100_rx_t, packet), buf, size);
    s->statistics.rx_good_frames++;
    eepro100_fr_interrupt(s);
    s->ru_offset = le32_to_cpu(rx.link);
    if (rfd_command & 0x8000) {
        /* EL bit is set, so this was the last frame. */
        assert(0);
    }
    if (rfd_command & 0x4000) {
        /* S bit is set. */
        set_ru_state(s, ru_suspended);
    }
}

static int nic_load(QEMUFile * f, void *opaque, int version_id)
{
    EEPRO100State *s = (EEPRO100State *) opaque;
    int i;
    int ret;

    if (version_id > 3)
        return -EINVAL;

    if (s->pci_dev && version_id >= 3) {
        ret = pci_device_load(s->pci_dev, f);
        if (ret < 0)
            return ret;
    }

    if (version_id >= 2) {
        qemu_get_8s(f, &s->rxcr);
    } else {
        s->rxcr = 0x0c;
    }

    qemu_get_8s(f, &s->cmd);
    qemu_get_be32s(f, &s->start);
    qemu_get_be32s(f, &s->stop);
    qemu_get_8s(f, &s->boundary);
    qemu_get_8s(f, &s->tsr);
    qemu_get_8s(f, &s->tpsr);
    qemu_get_be16s(f, &s->tcnt);
    qemu_get_be16s(f, &s->rcnt);
    qemu_get_be32s(f, &s->rsar);
    qemu_get_8s(f, &s->rsr);
    qemu_get_8s(f, &s->isr);
    qemu_get_8s(f, &s->dcfg);
    qemu_get_8s(f, &s->imr);
    qemu_get_buffer(f, s->phys, 6);
    qemu_get_8s(f, &s->curpag);
    qemu_get_buffer(f, s->mult, 8);
    qemu_get_buffer(f, s->mem, sizeof(s->mem));

    /* Restore all members of struct between scv_stat and mem */
    qemu_get_8s(f, &s->scb_stat);
    qemu_get_8s(f, &s->int_stat);
    for (i = 0; i < 3; i++)
        qemu_get_be32s(f, &s->region[i]);
    qemu_get_buffer(f, s->macaddr, 6);
    for (i = 0; i < 19; i++)
        qemu_get_be32s(f, &s->statcounter[i]);
    for (i = 0; i < 32; i++)
        qemu_get_be16s(f, &s->mdimem[i]);
    /* The eeprom should be saved and restored by its own routines */
    qemu_get_be32s(f, &s->device);
    qemu_get_be32s(f, &s->pointer);
    qemu_get_be32s(f, &s->cu_base);
    qemu_get_be32s(f, &s->cu_offset);
    qemu_get_be32s(f, &s->ru_base);
    qemu_get_be32s(f, &s->ru_offset);
    qemu_get_be32s(f, &s->statsaddr);
    /* Restore epro100_stats_t statistics */
    qemu_get_be32s(f, &s->statistics.tx_good_frames);
    qemu_get_be32s(f, &s->statistics.tx_max_collisions);
    qemu_get_be32s(f, &s->statistics.tx_late_collisions);
    qemu_get_be32s(f, &s->statistics.tx_underruns);
    qemu_get_be32s(f, &s->statistics.tx_lost_crs);
    qemu_get_be32s(f, &s->statistics.tx_deferred);
    qemu_get_be32s(f, &s->statistics.tx_single_collisions);
    qemu_get_be32s(f, &s->statistics.tx_multiple_collisions);
    qemu_get_be32s(f, &s->statistics.tx_total_collisions);
    qemu_get_be32s(f, &s->statistics.rx_good_frames);
    qemu_get_be32s(f, &s->statistics.rx_crc_errors);
    qemu_get_be32s(f, &s->statistics.rx_alignment_errors);
    qemu_get_be32s(f, &s->statistics.rx_resource_errors);
    qemu_get_be32s(f, &s->statistics.rx_overrun_errors);
    qemu_get_be32s(f, &s->statistics.rx_cdt_errors);
    qemu_get_be32s(f, &s->statistics.rx_short_frame_errors);
    qemu_get_be32s(f, &s->statistics.fc_xmt_pause);
    qemu_get_be32s(f, &s->statistics.fc_rcv_pause);
    qemu_get_be32s(f, &s->statistics.fc_rcv_unsupported);
    qemu_get_be16s(f, &s->statistics.xmt_tco_frames);
    qemu_get_be16s(f, &s->statistics.rcv_tco_frames);
    qemu_get_be32s(f, &s->statistics.complete);
#if 0
    qemu_get_be16s(f, &s->status);
#endif

    /* Configuration bytes. */
    qemu_get_buffer(f, s->configuration, sizeof(s->configuration));

    return 0;
}

static void nic_save(QEMUFile * f, void *opaque)
{
    EEPRO100State *s = (EEPRO100State *) opaque;
    int i;

    if (s->pci_dev)
        pci_device_save(s->pci_dev, f);

    qemu_put_8s(f, &s->rxcr);

    qemu_put_8s(f, &s->cmd);
    qemu_put_be32s(f, &s->start);
    qemu_put_be32s(f, &s->stop);
    qemu_put_8s(f, &s->boundary);
    qemu_put_8s(f, &s->tsr);
    qemu_put_8s(f, &s->tpsr);
    qemu_put_be16s(f, &s->tcnt);
    qemu_put_be16s(f, &s->rcnt);
    qemu_put_be32s(f, &s->rsar);
    qemu_put_8s(f, &s->rsr);
    qemu_put_8s(f, &s->isr);
    qemu_put_8s(f, &s->dcfg);
    qemu_put_8s(f, &s->imr);
    qemu_put_buffer(f, s->phys, 6);
    qemu_put_8s(f, &s->curpag);
    qemu_put_buffer(f, s->mult, 8);
    qemu_put_buffer(f, s->mem, sizeof(s->mem));

    /* Save all members of struct between scv_stat and mem */
    qemu_put_8s(f, &s->scb_stat);
    qemu_put_8s(f, &s->int_stat);
    for (i = 0; i < 3; i++)
        qemu_put_be32s(f, &s->region[i]);
    qemu_put_buffer(f, s->macaddr, 6);
    for (i = 0; i < 19; i++)
        qemu_put_be32s(f, &s->statcounter[i]);
    for (i = 0; i < 32; i++)
        qemu_put_be16s(f, &s->mdimem[i]);
    /* The eeprom should be saved and restored by its own routines */
    qemu_put_be32s(f, &s->device);
    qemu_put_be32s(f, &s->pointer);
    qemu_put_be32s(f, &s->cu_base);
    qemu_put_be32s(f, &s->cu_offset);
    qemu_put_be32s(f, &s->ru_base);
    qemu_put_be32s(f, &s->ru_offset);
    qemu_put_be32s(f, &s->statsaddr);
    /* Save epro100_stats_t statistics */
    qemu_put_be32s(f, &s->statistics.tx_good_frames);
    qemu_put_be32s(f, &s->statistics.tx_max_collisions);
    qemu_put_be32s(f, &s->statistics.tx_late_collisions);
    qemu_put_be32s(f, &s->statistics.tx_underruns);
    qemu_put_be32s(f, &s->statistics.tx_lost_crs);
    qemu_put_be32s(f, &s->statistics.tx_deferred);
    qemu_put_be32s(f, &s->statistics.tx_single_collisions);
    qemu_put_be32s(f, &s->statistics.tx_multiple_collisions);
    qemu_put_be32s(f, &s->statistics.tx_total_collisions);
    qemu_put_be32s(f, &s->statistics.rx_good_frames);
    qemu_put_be32s(f, &s->statistics.rx_crc_errors);
    qemu_put_be32s(f, &s->statistics.rx_alignment_errors);
    qemu_put_be32s(f, &s->statistics.rx_resource_errors);
    qemu_put_be32s(f, &s->statistics.rx_overrun_errors);
    qemu_put_be32s(f, &s->statistics.rx_cdt_errors);
    qemu_put_be32s(f, &s->statistics.rx_short_frame_errors);
    qemu_put_be32s(f, &s->statistics.fc_xmt_pause);
    qemu_put_be32s(f, &s->statistics.fc_rcv_pause);
    qemu_put_be32s(f, &s->statistics.fc_rcv_unsupported);
    qemu_put_be16s(f, &s->statistics.xmt_tco_frames);
    qemu_put_be16s(f, &s->statistics.rcv_tco_frames);
    qemu_put_be32s(f, &s->statistics.complete);
#if 0
    qemu_put_be16s(f, &s->status);
#endif

    /* Configuration bytes. */
    qemu_put_buffer(f, s->configuration, sizeof(s->configuration));
}

static void nic_init(PCIBus * bus, NICInfo * nd,
                     const char *name, uint32_t device)
{
    PCIEEPRO100State *d;
    EEPRO100State *s;

    logout("\n");

    d = (PCIEEPRO100State *) pci_register_device(bus, name,
                                                 sizeof(PCIEEPRO100State), -1,
                                                 NULL, NULL);

    s = &d->eepro100;
    s->device = device;
    s->pci_dev = &d->dev;

    pci_reset(s);

    /* Add 64 * 2 EEPROM. i82557 and i82558 support a 64 word EEPROM,
     * i82559 and later support 64 or 256 word EEPROM. */
    s->eeprom = eeprom93xx_new(EEPROM_SIZE);

    /* Handler for memory-mapped I/O */
    d->eepro100.mmio_index =
        cpu_register_io_memory(0, pci_mmio_read, pci_mmio_write, s);

    pci_register_io_region(&d->dev, 0, PCI_MEM_SIZE,
                           PCI_ADDRESS_SPACE_MEM |
                           PCI_ADDRESS_SPACE_MEM_PREFETCH, pci_mmio_map);
    pci_register_io_region(&d->dev, 1, PCI_IO_SIZE, PCI_ADDRESS_SPACE_IO,
                           pci_map);
    pci_register_io_region(&d->dev, 2, PCI_FLASH_SIZE, PCI_ADDRESS_SPACE_MEM,
                           pci_mmio_map);

    memcpy(s->macaddr, nd->macaddr, 6);
    logout("macaddr: %s\n", nic_dump(&s->macaddr[0], 6));
    assert(s->region[1] == 0);

    nic_reset(s);

    s->vc = qemu_new_vlan_client(nd->vlan, nd->model, nd->name,
                                 nic_receive, nic_can_receive, s);

    qemu_format_nic_info_str(s->vc, s->macaddr);

    qemu_register_reset(nic_reset, s);

    register_savevm(name, -1, 3, nic_save, nic_load, s);
}

void pci_i82551_init(PCIBus * bus, NICInfo * nd, int devfn)
{
    nic_init(bus, nd, "i82551", i82551);
    //~ uint8_t *pci_conf = d->dev.config;
}

void pci_i82557b_init(PCIBus * bus, NICInfo * nd, int devfn)
{
    nic_init(bus, nd, "i82557b", i82557B);
}

void pci_i82559er_init(PCIBus * bus, NICInfo * nd, int devfn)
{
    nic_init(bus, nd, "i82559er", i82559ER);
}

/* eof */