SD cards need to be instantiated via -drive if=sd. This means that all
cases where we use the blockdev path need to be special-cased for SD
cards.

Note that at this point QEMU_CAPS_BLOCKDEV is still cleared if the VM
config has a SD card.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Use the drive alias for all cases when we can't generate qomName. This
is meant to handle disks on 'sd' bus which are instantiated via -drive
if=sd as there isn't any specific QOM name for them.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

We still have to use -drive to instantiate sd disks. Combining that with
the new logic for blockjobs would be very complicated and not worth it
given that 'sd' cards work only on few rarely used machine types of
non-common architectures and libvirt didn't implement support for 'sd'
bus controllers. This will allow us to use -blockdev for other kinds on
such machines while sacrificing block jobs.

Note: this is currently no-op as we mask-out the QEMU_CAPS_BLOCKDEV
capability if any of the disks has bus='sd'.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

We can't set the type of the device on the 'sd' bus and realistically a
cdrom doesn't even make sense there. Forbid it.

Note that the output of in disk-cdrom-bus-other.x86_64-latest.args
switched to blockdev as it's no longer locked out due to use of a disk
on 'sd' bus.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

The 'vexpress-a9' ARM board supports the native 'sd' bus as well as
virtio. Add a test case for proving that upcoming changes to handling of
'sd' work. This config was also tested with real qemu and the qemu
process starts correctly.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

In case of 'sd' cards we'll use pre-blockdev code also if qemu supports
blockdev. In that specific case we'll need to mask out blockdev support
for 'sd' disks. Plumb in a boolean to allow it.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Make sure that we don't try to reload node names with -blockdev. If
something doesn't have a node name the update will not make the
situation better.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

There are no users for the qemu-specific enum values. Remove it.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

There's no point using the qemu-specific disk bus names in the error
message.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Remove all the universal code since the 'else' part formats commandline
only for the SD card based disk. Note that we can use virDiskNameToIndex
without the check as we already validate that 'disk->dst' contains a
properly formatted string in the validation code.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

For 'SD' disks and floppies in the pre-blockdev era we don't format
-device. Extract the logic so that it's more clear and add comments.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

The function effectively boils down to whether the disk is 'SD'. Since
we'll need to make more decisions based on the fact whether the disk is
on the SD bus, rename the function.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Remove the function and passing of 'def' through the callers.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Previously we've validated it in qemuCheckDiskConfig which was directly
called from the command line generator. Move the checks to the validator
where they belong.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Move the code from qemuCheckDiskConfigBlkdeviotune in
src/qemu/qemu_commandline.c to
qemuValidateDomainDeviceDefDiskBlkdeviotune.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Agregate validation of frontend properties in a new function called
qemuValidateDomainDeviceDefDiskFrontend.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Switch to DO_TEST_CAPS_LATEST for all of them and also add pre-blockdev
case for 'disk-discard' as we had it before.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Move the tests to DO_TEST_CAPS_LATEST. Since switch to blockdev stopped
us formatting the tunning parameters on the command line let's also add
version cases for qemu-4.1 data which doesn't enable blockdev.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

When firewalld is stopped, it removes *all* iptables rules and chains,
including those added by libvirt. Since restarting firewalld means
stopping and then starting it, any time it is restarted, libvirt needs
to recreate all the private iptables chains it uses, along with all
the rules it adds.

We already have code in place to call networkReloadFirewallRules() any
time we're notified of a firewalld start, and
networkReloadFirewallRules() will call
networkPreReloadFirewallRules(), which calls
networkSetupPrivateChains(); unfortunately that last call is called
using virOnce(), meaning that it will only be called the first time
through networkPreReloadFirewallRules() after libvirtd starts - so of
course when firewalld is later restarted, the call to
networkSetupPrivateChains() is skipped.

The neat and tidy way to fix this would be if there was a standard way
to reset a pthread_once_t object so that the next time virOnce was
called, it would think the function hadn't been called, and call it
again. Unfortunately, there isn't any official way of doing that (we
*could* just fill it with 0 and hope for the best, but that doesn't
seem very safe.

So instead, this patch just adds a static variable called
chainInitDone, which is set to true after networkSetupPrivateChains()
is called for the first time, and then during calls to
networkPreReloadFirewallRules(), if chainInitDone is set, we call
networkSetupPrivateChains() directly instead of via virOnce().

It may seem unsafe to directly call a function that is meant to be
called only once, but I think in this case we're safe - there's
nothing in the function that is inherently "once only" - it doesn't
initialize anything that can't safely be re-initialized (as long as
two threads don't try to do it at the same time), and it only happens
when responding to a dbus message that firewalld has been started (and
I don't think it's possible for us to be processing two of those at
once), and even then only if the initial call to the function has
already been completed (so we're safe if we receive a firewalld
restart call at a time when we haven't yet called it, or even if
another thread is already in the process of executing it. The only
problematic bit I can think of is if another thread is in the process
of adding an iptable rule at the time we're executing this function,
but 1) none of those threads will be trying to add chains, and 2) if
there was a concurrency problem with other threads adding iptables
rules while firewalld was being restarted, it would still be a problem
even without this change.

This is yet another patch that fixes an occurrence of this error:

COMMAND_FAILED: '/usr/sbin/iptables -w10 -w --table filter --insert LIBVIRT_INP --in-interface virbr0 --protocol tcp --destination-port 67 --jump ACCEPT' failed: iptables: No chain/target/match by that name.

In particular, this resolves: https://bugzilla.redhat.com/1813830Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>

networkSetupPrivateChains() is currently called only once per run of
libvirtd, so it can assume that errInitV4 and errInitV6 are empty/null
when it is called. In preparation for potentially calling this
function multiple times during one run, this patch moves the reset of
errInitV[46] to the top of the function, to assure no memory is
leaked.
Signed-off-by: NLaine Stump <laine@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>

As suggested in the linked bug, libvirt should firstly check
whether the major number of the device is device mapper major.
Because if it isn't subsequent DM_DEVICE_DEPS task may not only
fail, but also yield different results. In the bugzilla this is
demonstrated by creating a devmapper target named 'loop0' and
then creating loop target /dev/loop0. When the latter is then
passed to a domain, our virDevMapperGetTargetsImpl() function
blindly asks devmapper to provide target dependencies for
/dev/loop0 and because of the way devmapper APIs work, it will
'sanitize' the input by using the last component only which is
'loop0' and thus return different results than expected.

Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1823976Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>

This format is much easier to tweak and update.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>

It's been more than six months since we adopted GLib and we've
been pretty aggressive at replacing our homegrown APIs with more
standard ones, so by now most of the symbols mentioned in this
document haven't been around for quite a long time already.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>

With the move to GitLab CI one of the things we miss from Jenkins is a
single page dashboard showing CI status across all projects. This is a
very simple replacement that uses badges for CI pipeline status.

A CSS tweak is needed because RST->HTML adds redundant <p> tags inside
table cells which causes excessive vertical whitespace to appear.
Reviewed-by: NAndrea Bolognani <abologna@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

We have a framework to register cleanup callbacks that are run
when a domain is shut down. The idea is to run callbacks in
reverse order than they were registered. However, looking at the
code this is not the case. Fortunately, this framework is used to
register a single callback and a single callback only -
qemuMigrationDstPrepareCleanup() - therefore there was no problem
just yet.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

Commit a13b2905 missed an adjustment to a test that is only run when
building against xen <= 4.9, where LIBXL_HAVE_BUILDINFO_NESTED_HVM is
not defined. Adjust fullvirt-cpuid-legacy-nest test similar to the others.
Signed-off-by: NJim Fehlig <jfehlig@suse.com>

When no video device is specified in config we should set both
hvm.nographic to 1 and hvm.vga.kind to NONE.

Without hvm.vga.kind=LIBXL_VGA_INTERFACE_TYPE_NONE both -nographic and
-device 'cirrus-vga' are on qemu cmdline.
Signed-off-by: NArtur Puzio <contact@puzio.waw.pl>
Reviewed-by: NJim Fehlig <jfehlig@suse.com>

Turns out that it's not enough to pass the qemu:///embed root to
virQEMUDriverConfigNew(), you also have to make sure the same
string is copied into the virQEMUDriver structure yourself, and
not doing so in our case resulted in the cleanup never happening
and in distcheck failing because of that.

On the other hand, actually setting config->embeddedRoot would
result in different paths being generated for each test run, which
would obviously break qemuxml2argvtest, so that's not an option
either.

This reverts commit d98cc196.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>

Now that the QEMU driver natively supports storing all its runtime
data inside an arbitrary directory, we can avoid having multiple
copies of the same logic in the test suite.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

To attempt to catch unit tests which accidentally create files in $HOME,
or $XDG_RUNTIME_DIR, poison these env vars by pointing them to
directories which don't exist. This should give easier to debug test
failures. For example:

$ VIR_TEST_DEBUG=1 ./qemuhotplugtest
Could not initialize HostdevManager - operation failed: Failed to create state dir '/bad-test-used-env-xdg-runtime-dir/libvirt/hostdevmgr'
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>
Reviewed-by: NAndrea Bolognani <abologna@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

Fix win32 keycode for VK_OEM_102
Reviewed-by: NLaine Stump <laine@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

We need to prevent accidental deletion of release tags and maint
branches.

We need to ensure that shared CI runners are enabled on all repos.
Reviewed-by: NAndrea Bolognani <abologna@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

We need this for all tests that use virHostdevManager, because
during creation of this object for unprivileged connections
like those used in the test suite we would end up writing inside
the user's home directory.

That's bad manners in general, but when running the test suite
inside a purposefully constrained environment such as the one
exposed by pbuilder, it turns into an outright test failure:

  Could not initialize HostdevManager - operation failed: Failed
  to create state dir '/nonexistent/.cache/libvirt/hostdevmgr'
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

The churn in the output files is caused primarily by the fact that
blockdev support has been introduced.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

The churn in the output files is caused primarily by the fact that
replies were generated on a POWER9 machine, which is good because
we didn't have coverage of that before.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NMichal Privoznik <mprivozn@redhat.com>

So that we don't have to chase frequent Fedora releases, move the
non-build related jobs onto the long life CentOS 8 distro.
Reviewed-by: NAndrea Bolognani <abologna@redhat.com>
Signed-off-by: NDaniel P. Berrangé <berrange@redhat.com>

Currently, qemucapsprobe fails when libvirt is not already installed
on the system:

  $ ./tests/qemucapsprobe /path/to/qemu-system-ppc64 >/dev/null
  I/O warning : failed to load external entity "/usr/share/libvirt/cpu_map/index.xml"
  2020-05-06 09:49:59.136+0000: 269822: info : libvirt version: 6.4.0
  2020-05-06 09:49:59.136+0000: 269822: info : hostname: [...]
  2020-05-06 09:49:59.136+0000: 269822: warning : virQEMUCapsLogProbeFailure:5127 :
  Failed to probe capabilities for /path/to/qemu-system-ppc64: XML error: failed to
  parse xml document '/usr/share/libvirt/cpu_map/index.xml'

It would be great if the tool could work entirely out of the build
directory, and this patch achieves just that.
Suggested-by: NPeter Krempa <pkrempa@redhat.com>
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NDaniel P. Berrangé <berrange@redhat.com>