Tested with multiple AHCI controllers and multiple disks attached
to a controller. E.g.,

    <disk type='file' device='disk'>
      <driver name='qemu' type='raw'/>
      <source file='/var/lib/libvirt/images/test/disk0.raw'/>
      <target dev='sda' bus='sata'/>
      <address type='drive' controller='0' bus='0' unit='0'/>
    </disk>
    <disk type='file' device='disk'>
      <driver name='qemu' type='raw'/>
      <source file='/var/lib/libvirt/images/test/disk1.raw'/>
      <target dev='sdb' bus='sata'/>
      <address type='drive' controller='0' bus='0' unit='1'/>
    </disk>
    <disk type='file' device='disk'>
      <driver name='qemu' type='raw'/>
      <source file='/var/lib/libvirt/images/test/disk2.raw'/>
      <target dev='sdc' bus='sata'/>
      <address type='drive' controller='1' bus='0' unit='0'/>
    </disk>
    <controller type='sata' index='0'>
      <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/>
    </controller>
    <controller type='sata' index='1'>
      <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/>
    </controller>

Previously libvirt's disk device XML only had a single attribute,
error_policy, to control both read and write error policy, but qemu
has separate options for controlling read and write. In one case
(enospc) a policy is allowed for write errors but not read errors.

This patch adds a separate attribute that sets only the read error
policy. If just error_policy is set, it will apply to both read and
write error policy (previous behavior), but if the new rerror_policy
attribute is set, it will override error_policy for read errors only.
Possible values for rerror_policy are "stop", "report", and "ignore"
("report" is the qemu-controlled default for rerror_policy when
error_policy isn't specified).

For consistency, the value "report" has been added to the possible
values for error_policy as well.

commit 12062abb set rerror=ignore when error_policy="enospace" was
selected (since the rerror option in qemu doesn't accept "enospc", as
the werror option does).

After that patch was already pushed, Paolo Bonzini noticed it and
commented that leaving rerror at the default ("report") would be a
better choice. This patch corrects the problem - if error_policy =
"enospace" is given, rerror is left off the qemu commandline,
effectively setting it to "report". For other values, rerror is still
set to match werror.

Additionally, the parsing of error_policy was changed to no longer
erroneously allow "default" as a choice - as with most other
attributes, if you want the default setting, just don't specify an
error_policy.

Finally, two ommissions in the first patch were corrected - a
long-dormant qemuxml2argv test for enospace was enabled, and fixed to
pass, and the argv2xml parser in qemu_command.c was updated to
recognize the different spelling on the qemu commandline.

QEMU 0.13 introduced cache=unsafe for -drive, this patch exposes
it in the libvirt layer.

  * Introduced a new QEMU capability flag ($prefix_CACHE_UNSAFE),
    as even if $prefix_CACHE_V2 is set, we can't know if unsafe
    is supported.

  * Improved the reliability of qemu cache type detection.

The commit that prevents disk corruption on domain shutdown
(96fc4784) causes regression with QEMU
0.14.* and 0.15.* because of a regression bug in QEMU that was fixed
only recently in QEMU git. The affected versions of QEMU do not quit on
SIGTERM if started with -no-shutdown, which we use to implement fake
reboot. Since -no-shutdown tells QEMU not to quit automatically on guest
shutdown, domains started using the affected QEMU cannot be shutdown
properly and stay in a paused state.

This patch disables fake reboot feature on such QEMU by not using
-no-shutdown, which makes shutdown work as expected. However,
virDomainReboot will not work in this case and it will report "Requested
operation is not valid: Reboot is not supported with this QEMU binary".

As discussed here:
https://www.redhat.com/archives/libvir-list/2011-August/msg00361.html
https://www.redhat.com/archives/libvir-list/2011-August/msg00552.html

Adds snapshot attribute and transient sub-element:

<devices>
  <disk type=... snapshot='no|internal|external'>
    ...
    <transient/>
  </disk>
</devices>

* docs/schemas/domaincommon.rng (snapshot): New define.
(disk): Add snapshot and persistent attributes.
* docs/formatdomain.html.in: Document them.
* src/conf/domain_conf.h (virDomainDiskSnapshot): New enum.
(_virDomainDiskDef): New fields.
* tests/qemuxml2argvdata/qemuxml2argv-disk-transient.xml: New
test of rng, no args counterpart until qemu support is complete.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.args: New
file, snapshot attribute does not affect args.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.xml: Likewise.
* tests/qemuxml2argvtest.c (mymain): Run new test.

- create a new "redirdev" element for this purpose

QEMU uses USB bus name "usb.0" when using the legacy -usb argument.
If we want to allow USB devices to specify their addresses with legacy
-usb, we should either in case of legacy bus name drop the 0 from the
address bus, or just drop the 0 from device id. This patch does the
later.

Another solution would be to permit addressing on non-legacy USB
controllers only.

So that devices can be attached to hubs. Example, to attach to first
port of a usb-hub on port 1.

      <hub type='usb'>
         <address type='usb' bus='0' port='1'/>
      </hub>

      <input type='mouse' type='usb'>
         <address type='usb' bus='0' port='1.1'/>
      </hub>

also add a test entry

domain parsing and serialization code, qemu driver backend and
a couple of test

Companion controllers take an extra 'master' attribute to associate
them.

Also add tests for this

Expand the domain and the QEmu driver code
Adds a couple of tests

add a few tests for the new constructs

The model by default is piix3-uchi.

Example:
<controller type='usb' index='0' model='ich9-ehci'/>

Newer QEMU introduced cache=directsync for -drive, this patchset
is to expose it in libvirt layer.

  * Introduced a new QEMU capability flag ($prefix_CACHE_DIRECTSYNC),
    As even $prefix_CACHE_V2 is set, we can't known if directsync
    is supported.

In some versions of qemu, both virtio-blk-pci and virtio-net-pci
devices can have an event_idx setting that determines some details of
event processing. When it is enabled, it "reduces the number of
interrupts and exits for the guest". qemu will automatically enable
this feature when it is available, but there may be cases where this
new feature could actually make performance worse (NB: no such case
has been found so far).

As a safety switch in case such a situation is encountered in the
field, this patch adds a new attribute "event_idx" to the <driver>
element of both disk and interface devices. event_idx can be set to
"on" (to force event_idx on in case qemu has it disabled by default)
or "off" (for force event_idx off). In the case that event_idx support
isn't present in qemu, the attribute is ignored (this on the advice of
the qemu developer).

docs/formatdomain.html.in: document the new flag (marking it as
   "don't mess with this!"
docs/schemas/domain.rng: add event_idx in appropriate places
src/conf/domain_conf.[ch]: add event_idx to parser and formatter
src/libvirt_private.syms: export
   virDomainVirtioEventIdx(From|To)String
src/qemu/qemu_capabilities.[ch]: detect and report event_idx in
   disk/net
src/qemu/qemu_command.c: add event_idx parameter to qemu commandline
    when appropriate.
tests/qemuxml2argvdata/qemuxml2argv-event_idx.args,
tests/qemuxml2argvdata/qemuxml2argv-event_idx.xml,
tests/qemuxml2argvtest.c,
tests/qemuxml2xmltest.c: test cases for event_idx.

The drivers were accepting domain configs without checking if those
were actually meant for them. For example the LXC driver happily
accepts configs with type QEMU.

Add a check for the expected domain types to the virDomainDefParse*
functions.

This patch creates new <bios> element which, at this time has only the
attribute useserial='yes|no'. This attribute allow users to use
Serial Graphics Adapter and see BIOS messages from the very first moment
domain boots up. Therefore, users can choose boot medium, set PXE, etc.

For controlled shutdown we issue a 'system_powerdown' command
to the QEMU monitor. This triggers an ACPI event which (most)
guest OS wire up to a controlled shutdown. There is no equiv
ACPI event to trigger a controlled reboot. This patch attempts
to fake a reboot.

 - In qemuDomainObjPrivatePtr we have a bool fakeReboot
   flag.
 - The virDomainReboot method sets this flag and then
   triggers a normal 'system_powerdown'.
 - The QEMU process is started with '-no-shutdown'
   so that the guest CPUs pause when it powers off the
   guest
 - When we receive the 'POWEROFF' event from QEMU JSON
   monitor if fakeReboot is not set we invoke the
   qemuProcessKill command and shutdown continues
   normally
 - If fakeReboot was set, we spawn a background thread
   which issues 'system_reset' to perform a warm reboot
   of the guest hardware. Then it issues 'cont' to
   start the CPUs again

* src/qemu/qemu_command.c: Add -no-shutdown flag if
  we have JSON support
* src/qemu/qemu_domain.h: Add 'fakeReboot' flag to
  qemuDomainObjPrivate struct
* src/qemu/qemu_driver.c: Fake reboot using the
  system_powerdown command if JSON support is available
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
  src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
  src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
  binding for system_reset command
* src/qemu/qemu_process.c: Reset the guest & start CPUs if
  fakeReboot is set

For virtio disks and interfaces, qemu allows users to enable or disable
ioeventfd feature. This means, qemu can execute domain code, while
another thread waits for I/O event. Basically, in some cases it is win,
in some loss. This feature is available via 'ioeventfd' attribute in disk
and interface <driver> element. It accepts 'on' and 'off'. Leaving this
attribute out defaults to hypervisor decision.

Only add tests for qemuxmlargvtest.c, as there is no qemu command line
for numatune XML, just want to make sure the XML could be validated
well.

Prefer bootindex=N option for -device over the old way -boot ORDER
possibly accompanied with boot=on option for -drive. This gives us full
control over which device will actually be used for booting guest OS.
Moreover, if qemu doesn't support boot=on, this is the only way to boot
of certain disks in some configurations (such as virtio disks when used
together IDE disks) without transforming domain XML to use per device
boot elements.

and check regression

Make virtTestLoadFile allocate the buffer to read the file into.

Fix logic error in virtTestLoadFile, stop reading on the first empty line.

Use virFileReadLimFD in virtTestCaptureProgramOutput to avoid manual
buffer handling.

A few of the tests were missing basic sanity checks, while most
of them were doing copy-and-paste initialization (in fact, some
of them pasted the argc > 1 check more than once!).  It's much
nicer to do things in one common place, and minimizes the size of
the next patch that fixes getcwd usage.

* tests/testutils.h (EXIT_AM_HARDFAIL): New define.
(progname, abs_srcdir): Define for all tests.
(VIRT_TEST_MAIN): Change callback signature.
* tests/testutils.c (virtTestMain): Do more common init.
* tests/commandtest.c (mymain): Simplify.
* tests/cputest.c (mymain): Likewise.
* tests/esxutilstest.c (mymain): Likewise.
* tests/eventtest.c (mymain): Likewise.
* tests/hashtest.c (mymain): Likewise.
* tests/networkxml2xmltest.c (mymain): Likewise.
* tests/nodedevxml2xmltest.c (myname): Likewise.
* tests/nodeinfotest.c (mymain): Likewise.
* tests/nwfilterxml2xmltest.c (mymain): Likewise.
* tests/qemuargv2xmltest.c (mymain): Likewise.
* tests/qemuhelptest.c (mymain): Likewise.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2xmltest.c (mymain): Likewise.
* tests/qparamtest.c (mymain): Likewise.
* tests/sexpr2xmltest.c (mymain): Likewise.
* tests/sockettest.c (mymain): Likewise.
* tests/statstest.c (mymain): Likewise.
* tests/storagepoolxml2xmltest.c (mymain): Likewise.
* tests/storagevolxml2xmltest.c (mymain): Likewise.
* tests/virbuftest.c (mymain): Likewise.
* tests/virshtest.c (mymain): Likewise.
* tests/vmx2xmltest.c (mymain): Likewise.
* tests/xencapstest.c (mymain): Likewise.
* tests/xmconfigtest.c (mymain): Likewise.
* tests/xml2sexprtest.c (mymain): Likewise.
* tests/xml2vmxtest.c (mymain): Likewise.

v1 - v2:
  * Add missed tests/qemuxml2argvdata/qemuxml2argv-cputune.args

Latent bug introduced in commit 2d6a5819 (Aug 2009), but not exposed
until commit 1859939a (Jan 2011).  Basically, when virExec creates a
pipe, it always marks libvirt's side as cloexec.  If libvirt then
wants to hand that pipe to another child process, things work great if
the fd is dup2()'d onto stdin or stdout (as with stdin: or exec:
migration), but if the pipe is instead used as-is (such as with fd:
migration) then qemu sees EBADF because the fd was closed at exec().

This is a minimal fix for the problem at hand; it is slightly racy,
but no more racy than the rest of libvirt fd handling, including the
case of uncompressed save images.  A more invasive fix, but ultimately
safer at avoiding leaking unintended fds, would be to _always and
atomically_ open all fds as cloexec in libvirt (thanks to primitives
like open(O_CLOEXEC), pipe2(), accept4(), ...), then teach virExec to
clear that bit for all fds explicitly marked to be handed to the child
only after forking.

* src/qemu/qemu_command.c (qemuBuildCommandLine): Clear cloexec
flag.
* tests/qemuxml2argvtest.c (testCompareXMLToArgvFiles): Tweak test.

For qemu names the primary vga as "qxl-vga":

  1) if vram is specified for 2nd qxl device:

    -vga qxl -global qxl-vga.vram_size=$SIZE \
    -device qxl,id=video1,vram_size=$SIZE,...

  2) if vram is not specified for 2nd qxl device, (use the default
     set by global):

    -vga qxl -global qxl-vga.vram_size=$SIZE \
    -device qxl,id=video1,...

For qemu names all qxl devices as "qxl":

  1) if vram is specified for 2nd qxl device:

    -vga qxl -global qxl.vram_size=$SIZE \
    -device qxl,id=video1,vram_size=$SIZE ...

  2) if vram is not specified for 2nd qxl device:

    -vga qxl -global qxl-vga.vram_size=$SIZE \
    -device qxl,id=video1,...

"-global" is the only way to define vram_size for the primary qxl
device, regardless of how qemu names it, (It's not good a good
way, as original idea of "-global" is to set a global default for
a driver property, but to specify vram for first qxl device, we
have to use it).

For other qxl devices, as they are represented by "-device", could
specify it directly and seperately for each, and it overrides the
default set by "-global" if specified.

v1 - v2:
  * modify "virDomainVideoDefaultRAM" so that it returns 16M as the
    default vram_size for qxl device.

  * vram_size * 1024 (qemu accepts bytes for vram_size).

  * apply default vram_size for qxl device for which vram_size is
    not specified.

  * modify "graphics-spice" tests (more sensiable vram_size)

  * Add an argument of virDomainDefPtr type for qemuBuildVideoDevStr,
    to use virDomainVideoDefaultRAM in qemuBuildVideoDevStr).

v2 - v3:
  * Modify default video memory size for qxl device from 16M to 24M

  * Update codes to be consistent with changes on qemu_capabilities.*

Remove the <stdbool.h> header from all source files / headers
and just put it into internal.h

* src/internal.h: Add <stdbool.h>

This is done for two reasons:
- we are getting very close to 64 flags which is the maximum we can use
  with unsigned long long
- by using LL constants in enum we already violates C99 constraint that
  enum values have to fit into int

Three new functions (qemuCapsSet, qemuCapsClear, and qemuCapsGet) were
introduced replacing direct bit operations.

The new names comply more with the fact that they are all members of
enum qemuCapsFlags.

This is in response to:

   https://bugzilla.redhat.com/show_bug.cgi?id=629662

Explanation

qemu's virtio-net-pci driver allows setting the algorithm used for tx
packets to either "bh" or "timer". This is done by adding ",tx=bh" or
",tx=timer" to the "-device virtio-net-pci" commandline option.

'bh' stands for 'bottom half'; when this is set, packet tx is all done
in an iothread in the bottom half of the driver. (In libvirt, this
option is called the more descriptive "iothread".)

'timer' means that tx work is done in qemu, and if there is more tx
data than can be sent at the present time, a timer is set before qemu
moves on to do other things; when the timer fires, another attempt is
made to send more data. (libvirt retains the name "timer" for this
option.)

The resulting difference, according to the qemu developer who added
the option is:

    bh makes tx more asynchronous and reduces latency, but potentially
    causes more processor bandwidth contention since the cpu doing the
    tx isn't necessarily the cpu where the guest generated the
    packets.

Solution

This patch provides a libvirt domain xml knob to change the option on
the qemu commandline, by adding a new attribute "txmode" to the
<driver> element that can be placed inside any <interface> element in
a domain definition. It's use would be something like this:

    <interface ...>
      ...
      <model type='virtio'/>
      <driver txmode='iothread'/>
      ...
    </interface>

I chose to put this setting as an attribute to <driver> rather than as
a sub-element to <tune> because it is specific to the virtio-net
driver, not something that is generally usable by all network drivers.
(note that this is the same placement as the "driver name=..."
attribute used to choose kernel vs. userland backend for the
virtio-net driver.)

Actually adding the tx=xxx option to the qemu commandline is only done
if the version of qemu being used advertises it in the output of

    qemu -device virtio-net-pci,?

If a particular txmode is requested in the XML, and the option isn't
listed in that help output, an UNSUPPORTED_CONFIG error is logged, and
the domain fails to start.

QEMUD_CMD_FLAG_PCI_MULTIBUS should be set in the function
qemuCapsExtractVersionInfo()

The flag QEMUD_CMD_FLAG_PCI_MULTIBUS is used in the function
qemuBuildDeviceAddressStr(). All callers get qemuCmdFlags
by the function qemuCapsExtractVersionInfo() except that
testCompareXMLToArgvFiles() in qemuxml2argvtest.c.

So we should set QEMUD_CMD_FLAG_PCI_MULTIBUS in the function
qemuCapsExtractVersionInfo() instead of qemuBuildCommandLine()
because the function qemuBuildCommandLine() does not be called
when we attach a pci device.

tests: set QEMUD_CMD_FLAG_PCI_MULTIBUS in testCompareXMLToArgvFiles()

set QEMUD_CMD_FLAG_PCI_MULTIBUS before calling qemuBuildCommandLine()
as the flags is not set by qemuCapsExtractVersionInfo().
Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>