This patch adds support and documentation for
a generalized hardware cache event called cache_l1d
perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

Documents in formatdomain.html that when migrating a guest
defined with the host-passthrough CPU model from a machine that
is running on a newer CPU model than the destination machine's
CPU model, it is very likely that the guest will crash upon
arrival.
Signed-off-by: NJason J. Herne <jjherne@linux.vnet.ibm.com>

This patch adds support and documentation for
the ref_cpu_cycles perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

This patch adds support and documentation for
the stalled_cycles_backend perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

This patch adds support and documentation
for the stalled_cycles_frontend perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

This patch adds support and documentation
for the bus_cycles perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

This patch adds support and documentation
for the branch_misses perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

With current perf framework, this patch adds support and documentation
for the branch_instructions perf event.
Signed-off-by: NNitesh Konkar <nitkon12@linux.vnet.ibm.com>

Modify _virDomainBlockIoTuneInfo and rng schema to support the group_name
option for iotune throttling. Document the new value.
Signed-off-by: NJohn Ferlan <jferlan@redhat.com>

With the QEMU components in place, provide the XML parsing to
invoke that code when given the following XML snippet:

    <hostdev mode='subsystem' type='scsi_host'>
      <source protocol='vhost' wwpn='naa.501234567890abcd'/>
    </hostdev>

An optional address element can be specified within the hostdev
(pick CCW or PCI as necessary):

    <address type='ccw' cssid='0xfe' ssid='0x0' devno='0x0625'/>
    <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/>

Add basic vhost-scsi tests which were cloned from hostdev-scsi-virtio-scsi
in both xml2argv and xml2xml. Added ones for both vhost-scsi-ccw and
vhost-scsi-pci since the syntaxes are slightly different between them.

Also adjusted the docs to describe the changes.
Signed-off-by: NEric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: NBoris Fiuczynski <fiuczy@linux.vnet.ibm.com>

The <pre/> section is rendered as-is on the page. That is, if all
the lines are prefixed with 4 spaces the rendered page will also
have them. Problem is if we put a box around such <pre/> because
the content might not fix into it.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>

The old ivshmem is deprecated in QEMU, so let's use the better
ivshmem-{plain,doorbell} variants instead.
Signed-off-by: NMartin Kletzander <mkletzan@redhat.com>

Just the default one now, new ones will be added in following commits.
Signed-off-by: NMartin Kletzander <mkletzan@redhat.com>

Modify _virDomainBlockIoTuneInfo and rng schema to support the _length
options for bps/iops throttling values. Document the new values.

Add an optional "tls='yes|no'" attribute for a TCP chardev.

For QEMU, this will allow for disabling the host config setting of the
'chardev_tls' for a domain chardev channel by setting the value to "no" or
to attempt to use a host TLS environment when setting the value to "yes"
when the host config 'chardev_tls' setting is disabled, but a TLS environment
is configured via either the host config 'chardev_tls_x509_cert_dir' or
'default_tls_x509_cert_dir'
Signed-off-by: NJohn Ferlan <jferlan@redhat.com>
Signed-off-by: NPavel Hrdina <phrdina@redhat.com>

Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1369633Signed-off-by: NPavel Hrdina <phrdina@redhat.com>

https://bugzilla.redhat.com/show_bug.cgi?id=1381714

Alter the descriptions to match what the cpu_cycles actually is

Certain operations may make the vcpu order information invalid. Since
the order is primarily used to ensure migration compatibility and has
basically no other user benefits, clear the order prior to certain
operations and document that it may be cleared.

All the operations that would clear the order can still be properly
executed by defining a new domain configuration rather than using the
helper APIs.

Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1370357

When support was added for the kvm hidden='on' attribute in commit
d07116, the version requirement was listed as "2.1.0 (QEMU
only)". However, this was added when libvirt was at version 1.2.8 - it
is *QEMU* that must be at version 2.1.0 or later.

This went unnoticed for a very long time (over 2 years). Then a week
or two ago a new Windows convert in the #virt channel on OFTC was told
he needed to use this feature (to prevent nvidia drivers in a guest
from refusing to work due to being run in a virtual machine). There
was some problem with it being recognized and "someone" (it may have
been me, or may have been someone else, I don't remember) pointed out
that the documentation at

  http://www.libvirt.org/formatdomain.html

says that it requires libvirt 2.1.0. The next several days were filled
with agony as a new convert to Linux first tried to upgrade a Linux
Mint host running their "LTS" version to something newer, then tried
to install a libvirt build built for Ubuntu onto this, and later back
to the old LTS Linux Mint. After this he tried building his own
libvirt from source (with all the expected problems), and finally
switched to Fedora. In the end it was hours and hours of everybody's
lives that they will never get back. To now learn that he didn't need
to do this (his original libvirt version was 1.3.3, so whatever his
problem was, it was elsewhere) makes the pain all that much worse.

To prevent this from happening again, this simple patch changes the
version requirement for the kvm hidden attribute from "2.1.0 (QEMU
only)" to "1.2.8 (QEMU 2.1.0)".

So far only guestfwd and virtio were supported. Add an additional
for Xen as libxl channels create a Xen console visible to the guest.
Signed-off-by: NJoao Martins <joao.m.martins@oracle.com>
Signed-off-by: NJim Fehlig <jfehlig@suse.com>

https://bugzilla.redhat.com/show_bug.cgi?id=1366989

QEMU added another virtio-net tunable [1]. It basically allows
users to set the size of RX virtio ring. But because virtio-net
uses two separate ring buffers to pass data from/to guest they
named it explicitly rx_queue_size. We should expose it in our XML
too.

1: http://lists.nongnu.org/archive/html/qemu-devel/2016-08/msg02029.htmlSigned-off-by: NMichal Privoznik <mprivozn@redhat.com>

With current perf framework, this patch adds support and documentation
for more perf events, including cache misses, cache references, cpu cycles,
and instructions.
Signed-off-by: NQiaowei Ren <qiaowei.ren@intel.com>

The iothread example for virtio-scsi should be
<driver iothread='4'/> rather than <driver iothread='4'>
for the XML to be valid.

Make it clear that vcpu order is valid for online vcpus only and state
that it has to be specified for all vcpus or not provided at all.

Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1370043

Add support for using the new approach to hotplug vcpus using device_add
during startup of qemu to allow sparse vcpu topologies.

There are a few limitations imposed by qemu on the supported
configuration:
- vcpu0 needs to be always present and not hotpluggable
- non-hotpluggable cpus need to be ordered at the beginning
- order of the vcpus needs to be unique for every single hotpluggable
  entity

Qemu also doesn't really allow to query the information necessary to
start a VM with the vcpus directly on the commandline. Fortunately they
can be hotplugged during startup.

The new hotplug code uses the following approach:
- non-hotpluggable vcpus are counted and put to the -smp option
- qemu is started
- qemu is queried for the necessary information
- the configuration is checked
- the hotpluggable vcpus are hotplugged
- vcpus are started

This patch adds a lot of checking code and enables the support to
specify the individual vcpu element with qemu.

Individual vCPU hotplug requires us to track the state of any vCPU. To
allow this add the following XML:

<domain>
  ...
  <vcpu current='2'>3</vcpu>
  <vcpus>
    <vcpu id='0' enabled='yes' hotpluggable='no' order='1'/>
    <vcpu id='1' enabled='yes' hotpluggable='yes' order='2'/>
    <vcpu id='1' enabled='no' hotpluggable='yes'/>
  </vcpus>
  ...

The 'enabled' attribute allows to control the state of the vcpu.
'hotpluggable' controls whether given vcpu can be hotplugged and 'order'
allows to specify the order to add the vcpus.

I apparently misunderstood Marcel's description of what could and
couldn't be plugged into qemu's pxb-pcie controller (known as
pcie-expander-bus in libvirt) - I specifically allowed directly
connecting a pcie-switch-upstream-port, and it turns out that causes
the guest kernel to crash.

This patch forbids such a connection, and updates the xml docs
appropriately.

Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1361172

This element will control secure boot implemented by some
firmwares. If the firmware used in <loader/> does support the
feature we must tell it to the underlying hypervisor. However, we
can't know whether loader does support it or not just by looking
at the file. Therefore we have to have an attribute to the
element where users can tell us whether the firmware is secure
boot enabled or not.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>

Since its release of 2.4.0 qemu is able to enable System
Management Module in the firmware, or disable it. We should
expose this capability in the XML. Unfortunately, there's no good
way to determine whether the binary we are talking to supports
it. I mean, if qemu's run with real machine type, the smm
attribute can be seen in 'qom-list /machine' output. But it's not
there when qemu's run with -M none. Therefore we're stuck with
version based check.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>

https://bugzilla.redhat.com/show_bug.cgi?id=1356937

Add the definitions to allow for viewing/setting cgroup period and quota
limits for IOThreads.

This is similar to the work done for emulator quota and period by
commit ids 'b65dafa8' and 'e051c482'.

Being able to view/set the IOThread specific values is related to more
recent changes adding global period (commmit id '4d92d58f') and global
quota (commit id '55ecdae0') definitions and qemu support (commit id
'4e17ff79' and 'fbcbd1b2'). With a global setting though, if somehow
the IOThread value in the cgroup hierarchy was set "outside of libvirt"
to a value that is incompatible with the global value.

Allowing control over IOThread specific values provides the capability
to alter the IOThread values as necessary.

According to libxl implementation, it supports pvusb
controller of version 1.1 and version 2.0, and it
supports two types of backend, 'pvusb' (dom0 backend)
and 'qusb' (qemu backend). But currently pvusb backend
is not checked in yet.

To match libxl support, extend usb controller schema
to support two more models: qusb1 (qusb, version 1.1)
and 'qusb2' (qusb version 2.0).
Signed-off-by: NChunyan Liu <cyliu@suse.com>

To allow using failover with gluster it's necessary to specify multiple
volume hosts. Add support for starting qemu with such configurations.
Signed-off-by: NPeter Krempa <pkrempa@redhat.com>

A device with an attribute 'model', with just one model
so far:

<devices>
  ...
  <iommu model='intel'/>
</devices>

https://bugzilla.redhat.com/show_bug.cgi?id=1235580

This is place as a sub-element of <source>, where other aspects of the
host-side connection to the network device are located (network or
bridge name, udp listen port, etc). It's a bit odd that the interface
we're configuring with this info is itself named in <target dev='x'/>,
but that ship sailed long ago:

    <interface type='ethernet'>
      <mac address='00:16:3e:0f:ef:8a'/>
      <source>
        <ip address='192.168.122.12' family='ipv4'
            prefix='24' peer='192.168.122.1'/>
        <ip address='192.168.122.13' family='ipv4' prefix='24'/>
        <route family='ipv4' address='0.0.0.0'
               gateway='192.168.122.1'/>
        <route family='ipv4' address='192.168.124.0' prefix='24'
               gateway='192.168.124.1'/>
      </source>
    </interface>

In practice, this will likely only be useful for type='ethernet', so
its presence in any other type of interface is currently forbidden in
the generic device Validate function (but it's been put into the
general population of virDomainNetDef rather than the
ethernet-specific union member so that 1) we can more easily add the
capability to other types if needed, and 2) we can retain the info
when set to an invalid interface type all the way through to
validation and report a proper error, rather than just ignoring it
(which is currently what happens for many other type-specific
settings).

(NB: The already-existing configuration of IP info for the guest-side
of interfaces is in subelements directly under <interface>, and the
name of the guest-side interface (when configurable) is in <guest
dev='x'/>).

(This patch had been pushed earlier in
commit fe6a7789, but was reverted in
commit d6584565 because it had been
accidentally pushed during the freeze for release 2.0.0)

The peer attribute is used to set the property of the same name in the
interface IP info:

  <interface type='ethernet'>
    ...
    <ip family='ipv4' address='192.168.122.5'
        prefix='32' peer='192.168.122.6'/>
    ...
  </interface>

Note that this element is used to set the IP information on the
*guest* side interface, not the host side interface - that will be
supported in an upcoming patch.

(This patch now has quite a history: it was originally pushed in
commit 690969af, which was subsequently reverted in commit 1d14b13f,
then reworked and pushed (along with a lot of other related/supporting
patches) in commit 93135abf; however *that* commit had been
accidentally pushed during dev. freeze for release 2.0.0, so it was
again reverted in commit f6acf039).
Signed-off-by: NVasiliy Tolstov <v.tolstov@selfip.ru>
Signed-off-by: NLaine Stump <laine@laine.org>

https://bugzilla.redhat.com/show_bug.cgi?id=1046833Signed-off-by: NJiri Denemark <jdenemar@redhat.com>

This reverts commit 93135abf.

This feature was accidentally pushed in the feature freeze.

This reverts commit fe6a7789.

This feature was accidentally pushed in the feature freeze.

This is place as a sub-element of <source>, where other aspects of the
host-side connection to the network device are located (network or
bridge name, udp listen port, etc). It's a bit odd that the interface
we're configuring with this info is itself named in <target dev='x'/>,
but that ship sailed long ago:

    <interface type='ethernet'>
      <mac address='00:16:3e:0f:ef:8a'/>
      <source>
        <ip address='192.168.122.12' family='ipv4'
            prefix='24' peer='192.168.122.1'/>
        <ip address='192.168.122.13' family='ipv4' prefix='24'/>
        <route family='ipv4' address='0.0.0.0'
               gateway='192.168.122.1'/>
        <route family='ipv4' address='192.168.124.0' prefix='24'
               gateway='192.168.124.1'/>
      </source>
    </interface>

In practice, this will likely only be useful for type='ethernet', so
its presence in any other type of interface is currently forbidden in
the generic device Validate function (but it's been put into the
general population of virDomainNetDef rather than the
ethernet-specific union member so that 1) we can more easily add the
capability to other types, and 2) we can retain the info when set to
an invalid interface type all the way through to validation and report
a proper error, rather than just ignoring it (which is currently what
happens for many other type-specific settings).

(NB: The already-existing configuration of IP info for the guest-side
of interfaces is in subelements directly under <interface>, and the
name of the guest-side interface (when configurable) is in <guest
dev='x'/>).

The peer attribute is used to set the property of the same name in the
interface IP info:

  <interface type='ethernet'>
    ...
    <ip family='ipv4' address='192.168.122.5'
        prefix='32' peer='192.168.122.6'/>
    ...
  </interface>

Note that this element is used to set the IP information on the
*guest* side interface, not the host side interface - that will be
supported in an upcoming patch.

(This is an updated *re*-commit of commit 690969af, which was
subsequently reverted in commit 1d14b13f).
Signed-off-by: NVasiliy Tolstov <v.tolstov@selfip.ru>
Signed-off-by: NLaine Stump <laine@laine.org>