This patch implements the remote protocol to address the new API.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>

This patch implements the code to address the new API
in the qemu driver.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>

This patch introduces a new libvirt API (virDomainSetMemoryFlags) and
a flag (virDomainMemoryModFlags).
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>

Opening raw network devices with the intent of passing those fds to
qemu is worth an audit point.  This makes a multi-part audit: first,
we audit the device(s) that libvirt opens on behalf of the MAC address
of a to-be-created interface (which can independently succeed or
fail), then we audit whether qemu actually started the network device
with the same MAC (so searching backwards for successful audits with
the same MAC will show which fd(s) qemu is actually using).  Note that
it is possible for the fd to be successfully opened but no attempt
made to pass the fd to qemu (for example, because intermediate
nwfilter operations failed) - no interface start audit will occur in
that case; so the audit for a successful opened fd does not imply
rights given to qemu unless there is a followup audit about the
attempt to start a new interface.

Likewise, when a network device is hot-unplugged, there is only one
audit message about the MAC being discontinued; again, searching back
to the earlier device open audits will show which fds that qemu quits
using (and yes, I checked via /proc/<qemu-pid>/fd that qemu _does_
close out the fds associated with an interface on hot-unplug).  The
code would require much more refactoring to be able to definitively
state which device(s) were discontinued at that point, since we
currently don't record anywhere in the XML whether /dev/vhost-net was
opened for a given interface.

* src/qemu/qemu_audit.h (qemuAuditNetDevice): New prototype.
* src/qemu/qemu_audit.c (qemuAuditNetDevice): New function.
* src/qemu/qemu_command.h (qemuNetworkIfaceConnect)
(qemuPhysIfaceConnect, qemuOpenVhostNet): Adjust prototype.
* src/qemu/qemu_command.c (qemuNetworkIfaceConnect)
(qemuPhysIfaceConnect, qemuOpenVhostNet): Add audit points and
adjust parameters.
(qemuBuildCommandLine): Adjust caller.
* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Likewise.

Since libvirt always passes /dev/net/tun to qemu via fd, we should
never trigger the cases where qemu tries to directly open the
device.  Therefore, it is safer to deny the cgroup device ACL.

* src/qemu/qemu_cgroup.c (defaultDeviceACL): Remove /dev/net/tun.
* src/qemu/qemu.conf (cgroup_device_acl): Reflect this change.

* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Honor vhost
designations, similar to qemu_command code paths.
* src/qemu/qemu_command.h (qemuOpenVhostNet): New prototype.
* src/qemu/qemu_command.c (qemuOpenVhostNet): Export.

qemu driver in libvirt gained support for creating domain snapshots
almost a year ago in libvirt 0.8.0. Since then we enabled QMP support
for qemu >= 0.13.0 but QMP equivalents of {save,load,del}vm commands are
not implemented in current qemu (0.14.0) so the domain snapshot support
is not very useful.

This patch detects when the appropriate QMP command is not implemented
and tries to use human-monitor-command (aka HMP passthrough) to run
it's HMP equivalent.

To make it more obvious that it is only used for text monitor. The
naming also matches the style of qemuMonitorTextCommandWithFd.

So that it's obvious that they are supposed to be used with HMP commands.

JSON monitor command implementation can now just directly call text
monitor implementation and it will be automatically encapsulated into
QMP's human-monitor-command.

Some qemu monitor event handlers were issuing inadequate warning when
virDomainSaveStatus() failed. They copied the message from I/O error
handler without customizing it to provide better information on why
virDomainSaveStatus() was called.

For newer qemu-img, the help string for "backing file format" is
"[-F backing_fmt]".

Fix the wrong logic error by commit e997c268.

* src/storage/storage_backend.c

qemu-img silently disable "-e", so we can't use it for volume
encryption anymore, change it into "-o encryption=on" if qemu
supports "-o" option.

* src/qemu/qemu_audit.h (qemuAuditCgroupMajor)
(qemuAuditCgroupPath): Add parameter.
* src/qemu/qemu_audit.c (qemuAuditCgroupMajor)
(qemuAuditCgroupPath): Add 'acl=rwm' to cgroup audit entries.
* src/qemu/qemu_cgroup.c: Update clients.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Likewise.

Adding audit points showed that we were granting too much privilege
to qemu; it should not need any mknod rights to recreate any
devices.  On the other hand, lxc should have all device privileges.
The solution is adding a flag parameter.

This also lets us restrict write access to read-only disks.

* src/util/cgroup.h (virCgroup*Device*): Adjust prototypes.
* src/util/cgroup.c (virCgroupAllowDevice)
(virCgroupAllowDeviceMajor, virCgroupAllowDevicePath)
(virCgroupDenyDevice, virCgroupDenyDeviceMajor)
(virCgroupDenyDevicePath): Add parameter.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Update clients.
* src/lxc/lxc_controller.c (lxcSetContainerResources): Likewise.
* src/qemu/qemu_cgroup.c: Likewise.
(qemuSetupDiskPathAllow): Also, honor read-only disks.

Also add ATTRIBUTE_NONNULL markers.

* src/qemu/qemu_audit.h: The pattern qemuDomainXXXAudit is
inconsistent; prefer qemuAuditXXX instead.
* src/qemu/qemu_audit.c: Reflect the renames.
* src/qemu/qemu_driver.c: Likewise.
* src/qemu/qemu_hotplug.c: Likewise.
* src/qemu/qemu_migration.c: Likewise.
* src/qemu/qemu_process.c: Likewise.

Although the cgroup device ACL controller path can be worked out
by researching the code, it is more efficient to include that
information directly in the audit message.

* src/util/cgroup.h (virCgroupPathOfController): New prototype.
* src/util/cgroup.c (virCgroupPathOfController): Export.
* src/libvirt_private.syms: Likewise.
* src/qemu/qemu_audit.c (qemuAuditCgroup): Use it.

Device names can be manipulated, so it is better to also log
the major/minor device number corresponding to the cgroup ACL
changes that libvirt made.  This required some refactoring
of the relatively new qemu cgroup audit code.

Also, qemuSetupChardevCgroup was only auditing on failure, not success.

* src/qemu/qemu_audit.h (qemuDomainCgroupAudit): Delete.
(qemuAuditCgroup, qemuAuditCgroupMajor, qemuAuditCgroupPath): New
prototypes.
* src/qemu/qemu_audit.c (qemuDomainCgroupAudit): Rename...
(qemuAuditCgroup): ...and drop a parameter.
(qemuAuditCgroupMajor, qemuAuditCgroupPath): New functions, to
allow listing device major/minor in audit.
(qemuAuditGetRdev): New helper function.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Adjust callers.
* src/qemu/qemu_cgroup.c (qemuSetupDiskPathAllow)
(qemuSetupHostUsbDeviceCgroup, qemuSetupCgroup)
(qemuTeardownDiskPathDeny): Likewise.
(qemuSetupChardevCgroup): Likewise, fixing missing audit.

* src/qemu/qemu_audit.c (qemuDomainHostdevAudit): Avoid use of
"type", which has a pre-defined meaning.
(qemuDomainCgroupAudit): Likewise, as well as "item".

I noticed these while testing 'make dist'.

Parsing ./../src/util/event.c
Function comment for virEventRegisterDefaultImpl lacks description of return value
Function comment for virEventRunDefaultImpl lacks description of return value
Parsing ./../src/util/virterror.c
Missing comment for function virSetErrorLogPriorityFunc

* src/util/event.c (virEventRegisterDefaultImpl)
(virEventRunDefaultImpl): Document return types.
* src/util/virterror.c (virSetErrorLogPriorityFunc): Provide docs.

* docs/formatdomain.html.in: Document virtio backend selection.

otherwise the user might not have enough permissions to access the
socket if root's umask is 077.

http://bugs.debian.org/614210

virRun gives pretty useful error output, let's not overwrite it unless there
is a good reason. Some places were providing more information about what
the commands were _attempting_ to do, however that's usually less useful from
a debugging POV than what actually happened.

as described at
http://wiki.debian.org/ToolChain/DSOLinking
https://fedoraproject.org/wiki/UnderstandingDSOLinkChange

otherwise the build fails on current Debian unstable with:

CCLD   libvirtd
/usr/bin/ld: ../src/.libs/libvirt_driver_lxc.a(libvirt_driver_lxc_la-lxc_container.o): undefined reference to symbol 'capng_apply'
/usr/bin/ld: note: 'capng_apply' is defined in DSO //usr/lib/libcap-ng.so.0 so try adding it to the linker command line

CCLD   libvirtd
/usr/bin/ld: ../src/.libs/libvirt_driver_storage.a(libvirt_driver_storage_la-storage_backend.o): undefined reference to symbol 'fgetfilecon'
/usr/bin/ld: note: 'fgetfilecon' is defined in DSO //lib/libselinux.so.1 so try adding it to the linker command line
//lib/libselinux.so.1: could not read symbols: Invalid operation

and similar errors.

* src/qemu/qemu_driver.c: qemuDomainUpdateDeviceFlags() is not disk
  specific as the message suggests

On cygwin:

  CC       libvirt_driver_security_la-security_dac.lo
security/security_dac.c: In function 'virSecurityDACSetProcessLabel':
security/security_dac.c:618: warning: format '%d' expects type 'int', but argument 7 has type 'uid_t' [-Wformat]

We've done this before (see src/util/util.c).

* src/security/security_dac.c (virSecurityDACSetProcessLabel): On
cygwin, uid_t is a 32-bit long.

On cygwin:

  CC        libvirt_util_la-cgroup.lo
util/cgroup.c: In function 'virCgroupKillRecursiveInternal':
util/cgroup.c:1458: warning: implicit declaration of function 'virCgroupNew' [-Wimplicit-function-declaration]

* src/util/cgroup.c (virCgroupKill): Don't build on platforms
where virCgroupNew is unsupported.

When building libvirt without libvirtd, I receive the following errors:
make[1]: Leaving directory `/home/wency/source/test/libvirt/src'
 (cd daemon && make  top_distdir=../libvirt-0.8.8 distdir=../libvirt-0.8.8/daemon \
     am__remove_distdir=: am__skip_length_check=: am__skip_mode_fix=: distdir)
make[1]: Entering directory `/home/wency/source/test/libvirt/daemon'
make[1]: *** No rule to make target `libvirtd.8.in', needed by `distdir'.  Stop.

This bug was caused by commit 6db98a2d.
Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>
Signed-off-by: NEric Blake <eblake@redhat.com>

* docs/formatdomain.html.in: Fix typo.

as described at
http://wiki.debian.org/ToolChain/DSOLinking
https://fedoraproject.org/wiki/UnderstandingDSOLinkChange

otherwise the build fails on current Debian unstable with:

CCLD   virsh
/usr/bin/ld: virsh-virsh.o: undefined reference to symbol 'xmlSaveTree@@LIBXML2_2.6.8'
/usr/bin/ld: note: 'xmlSaveTree@@LIBXML2_2.6.8' is defined in DSO //usr/lib/libxml2.so.2 so try adding it to the linker command line
//usr/lib/libxml2.so.2: could not read symbols: Invalid operation

This is needed to detect situations when optional argument was
specified with non-integer value: '--int-opt foo'. To keep functions
uniform vshCommandOptString function was also changed, because it
returns tri-state value as well. Given result pointer is updated only
in case of success. If parsing fails, result is not updated at all.

This function should return pointer to const, because we don't want
to change command option value. Therefore we can ensure const-correctness.

Apparently some signals found on Unix are not exposed, this led
to a compilation failure
* src/util/logging.c: make code related to each signal dependant
  upon the definition of that signal

Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>

The way to detach a USB disk is the same as that to detach a SCSI
disk. Rename this function and we can use it to detach a USB disk.
Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>