For every but the last argument, we also need space for a space
and a backslash.

Rewrap everything longer than 78 characters.

Support for SMP topology was added by qemu commit dc6b1c09849484fbbc50
prior to 0.12.0, our minimum supported qemu version.

$ git describe --tags dc6b1c09849484fbbc50803307e4c7a3d81eab62
v0.11.0-rc0-449-gdc6b1c0
$ git describe --tags --contains dc6b1c09849484fbbc50803307e4c7a3d81eab
v0.12.0-rc0~1477

Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca3).  However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited.  In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains).  That way we can change it
in the future.

The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: NMartin Kletzander <mkletzan@redhat.com>

Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:

    <disk type='file' device='cdrom'>
      <driver name='qemu' type='raw'/>
      <target dev='hda' bus='ide'/>
      <readonly/>
      <address type='drive' controller='0' bus='0' target='0' unit='0'/>
    </disk>

and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>

As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

The -uuid arg was added in QEMU 0.10.0, so the QEMU driver can
assume it is always available.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

The -name arg was added in QEMU 0.9.1, so the QEMU driver can
assume it is always available.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

Back in

  commit bd6c46fa
  Author: Juerg Haefliger <juerg.haefliger@hp.com>
  Date:   Mon Jan 31 06:42:57 2011 -0500

    tests: handle backspace-newline pairs in test input files

all the test argv files were line wrapped so that the args
were less than 80 characters.

The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.

This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.

This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.

A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.

Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.

Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)

The alias for hostdevs of type SCSI can be too long for QEMU if
larger LUNs are encountered. Here's a real life example:

    <hostdev mode='subsystem' type='scsi' managed='no'>
      <source>
        <adapter name='scsi_host0'/>
        <address bus='0' target='19' unit='1088634913'/>
      </source>
      <address type='drive' controller='0' bus='0' target='0' unit='0'/>
    </hostdev>

this results in a too long drive id, resulting in QEMU yelling

Property 'scsi-generic.drive' can't find value 'drive-hostdev-scsi_host0-0-19-1088634913'

This commit changes the alias back to the default hostdev$(index)
scheme.
Signed-off-by: NViktor Mihajlovski <mihajlov@linux.vnet.ibm.com>

Long lines are harder to read and harder to diff; in fact, if lines get
too long (> 1000 bytes), it starts causing issues where git send-email
refuses to send patches for the file.  I've cleaned up the tests
directory in the past (see commits bd6c46fa, 3b750d13), but new long
lines have been introduced in the meantime.

Why 90 instead of 80? Because there were too many tests on the fringe
edge, and I didn't want to edit that many files.

Add a syntax check to prevent future long lines.

* cfg.mk (sc_prohibit_long_lines): New rule.
* tests/qemuxml2argvdata/qemuxml2argv-*.args: Split lines of any
file with content longer than 90 columns.
* tests/storagevolxml2argvdata/*.argv: Likewise.
Signed-off-by: NEric Blake <eblake@redhat.com>

Except the scsi host device's controller is "lsilogic", mapping
between the libvirt attributes and scsi-generic properties is:

  libvirt     qemu
-----------------------------------------
  controller  bus ($libvirt_controller.0)
  bus         channel
  target      scsi-id
  unit        lun

For scsi host device with "lsilogic" controller, the mapping is:
('target (libvirt)' must be 0, as it's not used; 'unit (libvirt)
must <= 7).

  libvirt            qemu
----------------------------------------------------------
  controller && bus  bus ($libvirt_controller.$libvirt_bus)
  unit               scsi-id

It's not good to hardcode/hard-check limits of these attributes,
and even worse, these limits are not documented, one has to find
out by either testing or reading the qemu code, I'm looking forward
to qemu expose limits like these one day). For example, exposing
"max_target", "max_lun" for megasas:

static const struct SCSIBusInfo megasas_scsi_info = {
    .tcq = true,
    .max_target = MFI_MAX_LD,
    .max_lun = 255,

    .transfer_data = megasas_xfer_complete,
    .get_sg_list = megasas_get_sg_list,
    .complete = megasas_command_complete,
    .cancel = megasas_command_cancel,
};

Example of the qemu command line (lsilogic controller):

  -drive file=/dev/sg2,if=none,id=drive-hostdev-scsi_host7-0-0-0 \
  -device scsi-generic,bus=scsi0.0,scsi-id=8,\
  drive=drive-hostdev-scsi_host7-0-0-0,id=hostdev-scsi_host7-0-0-0

Example of the qemu command line (virtio-scsi controller):

  -drive file=/dev/sg2,if=none,id=drive-hostdev-scsi_host7-0-0-0 \
  -device scsi-generic,bus=scsi0.0,channel=0,scsi-id=128,lun=128,\
  drive=drive-hostdev-scsi_host7-0-0-0,id=hostdev-scsi_host7-0-0-0
Signed-off-by: NHan Cheng <hanc.fnst@cn.fujitsu.com>
Signed-off-by: NOsier Yang <jyang@redhat.com>