We didn't do this earlier because the DO_TEST_CAPS_ARCH_LATEST()
macro was limited to qemuxml2argv until recently.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NJán Tomko <jtomko@redhat.com>

There's no reason for the files to have qemuxml2xmlout- prefix
since they all live under qemuxml2xmloutdata directory.
Signed-off-by: NMichal Privoznik <mprivozn@redhat.com>

Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NPavel Hrdina <phrdina@redhat.com>

This attribute was used to decide whether to format the type
attribute of the <target> element, but the logic didn't take into
account all possible cases and as such could lead to unexpected
results. Moreover, it's one more thing to keep track of, and can
easily fall out of sync with other attributes.

Now that we have VIR_DOMAIN_CHR_SERIAL_TARGET_TYPE_NONE, we can
use that value to signal that no specific target type has been
configured for the serial device and as such the attribute should
not be formatted at all. All other values are now formatted.
Signed-off-by: NAndrea Bolognani <abologna@redhat.com>
Reviewed-by: NPavel Hrdina <phrdina@redhat.com>

Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.

Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: NPavel Hrdina <phrdina@redhat.com>

Set the VIR_PCI_CONNECT_AGGREGATE_SLOT flag for pcie-root-ports so
that they will be assigned to all the functions on a slot.

Some qemu test case outputs had to be adjusted due to the
pcie-root-ports now being put on multiple functions.

For machinetypes with a pci-root bus (all legacy PCI), libvirt will
make a "fake" reservation for one extra slot prior to assigning
addresses to unaddressed PCI endpoint devices in the domain. This will
trigger auto-adding of a pci-bridge for the final device to be
assigned an address *if that device would have otherwise instead been
the last device on the last available pci-bridge*; thus it assures
that there will always be at least one slot left open in the domain's
bus topology for expansion (which is important both for hotplug (since
a new pci-bridge can't be added while the guest is running) as well as
for offline additions to the config (since adding a new device might
otherwise in some cases require re-addressing existing devices, which
we want to avoid)).

It's important to note that for the above case (legacy PCI), we must
check for the special case of all slots on all buses being occupied
*prior to assigning any addresses*, and avoid attempting to reserve
the extra address in that case, because there is no free address in
the existing topology, so no place to auto-add a pci-bridge for
expansion (i.e. it would always fail anyway). Since that condition can
only be reached by manual intervention, this is acceptable.

For machinetypes with pcie-root (Q35, aarch64 virt), libvirt's
methodology for automatically expanding the bus topology is different
- pcie-root-ports are plugged into slots (soon to be functions) of
pcie-root as needed, and the new endpoint devices are assigned to the
single slot in each pcie-root-port. This is done so that the devices
are, by default, hotpluggable (the slots of pcie-root don't support
hotplug, but the single slot of the pcie-root-port does). Since
pcie-root-ports can only be plugged into pcie-root, and we don't
auto-assign endpoint devices to the pcie-root slots, this means
topology expansion doesn't compete with endpoint devices for slots, so
we don't need to worry about checking for all "useful" slots being
free *prior* to assigning addresses to new endpoint devices - as a
matter of fact, if we attempt to reserve the open slots before the
used slots, it can lead to errors.

Instead this patch just reserves one slot for a "future potential"
PCIe device after doing the assignment for actual devices, but only
if the only PCI controller defined prior to starting address
assignment was pcie-root, and only if we auto-added at least one PCI
controller during address assignment. This assures two things:

1) that reserving the open slots will only be done when the domain is
   initially defined, never at any time after, and

2) that if the user understands enough about PCI controllers that they
   are adding them manually, that we don't mess up their plan by
   adding extras - if they know enough to add one pcie-root-port, or
   to manually assign addresses such that no pcie-root-ports are
   needed, they know enough to add extra pcie-root-ports if they want
   them (this could be called the "libguestfs clause", since
   libguestfs needs to be able to create domains with as few
   devices/controllers as possible).

This is set to reserve a single free port for now, but could be
increased in the future if public sentiment goes in that direction
(it's easy to increase later, but essentially impossible to decrease)

Real Q35 hardware has an ICH9 chip that includes several integrated
devices at particular addresses (see the file docs/q35-chipset.cfg in
the qemu source). libvirt already attempts to put the first two sets
of ich9 USB2 controllers it finds at 00:1D.* and 00:1A.* to match the
real hardware. This patch does the same for the ich9 "HD audio"
device.

The main inspiration for this patch is that currently the *only*
device in a reasonable "workstation" type virtual machine config that
requires a legacy PCI slot is the audio device, Without this patch,
the standard Q35 machine created by virt-manager will have a
dmi-to-pci-bridge and a pci-bridge just for the sound device; with the
patch (and if you change the sound device model from the default
"ich6" to "ich9"), the machine definition constructed by virt-manager
has absolutely no legacy PCI controllers - any legacy PCI devices
(e.g. video and sound) are on pcie-root as integrated devices.