The capabilities used in test cases should match those used
during normal operation for the tests to make any sense.

This results in the generated command line for a few test
cases (most notably non-x86 test cases that were wrongly
assuming they could use -no-acpi) changing.

virQEMUCapsHasPCIMultiBus() performs a version check on
the QEMU binary to figure out whether multiple buses are
supported, so to get the correct aliases assigned when
dealing with pSeries guests we need to spoof the version
accordingly in the test suite.

Support for SMP topology was added by qemu commit dc6b1c09849484fbbc50
prior to 0.12.0, our minimum supported qemu version.

$ git describe --tags dc6b1c09849484fbbc50803307e4c7a3d81eab62
v0.11.0-rc0-449-gdc6b1c0
$ git describe --tags --contains dc6b1c09849484fbbc50803307e4c7a3d81eab
v0.12.0-rc0~1477

Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca3).  However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited.  In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains).  That way we can change it
in the future.

The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: NMartin Kletzander <mkletzan@redhat.com>

QEMU_CAPS_DEVICE is always enabled for qemu binaries we support.
Sync qemuxml2* to match, and regenerate all test output.

The -uuid arg was added in QEMU 0.10.0, so the QEMU driver can
assume it is always available.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

The -name arg was added in QEMU 0.9.1, so the QEMU driver can
assume it is always available.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

Back in

  commit bd6c46fa
  Author: Juerg Haefliger <juerg.haefliger@hp.com>
  Date:   Mon Jan 31 06:42:57 2011 -0500

    tests: handle backspace-newline pairs in test input files

all the test argv files were line wrapped so that the args
were less than 80 characters.

The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.

This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.

This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>

ppce500v2 is not machine supported by official release of QEMU.
It should be replaced by ppce500.
Signed-off-by: NJán Tomko <jtomko@redhat.com>

On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.

A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.

Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.

Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)

The "dtb" option sets the filename for the device tree.
If without this option support, "-dtb file" will be converted into
<qemu:commandline> in domain XML file.
For example, '-dtb /media/ram/test.dtb' will be converted into
  <qemu:commandline>
    <qemu:arg value='-dtb'/>
    <qemu:arg value='/media/ram/test.dtb'/>
  </qemu:commandline>

This is not very friendly.
This patchset add special <dtb> tag like <kernel> and <initrd>
which is easier for user to write domain XML file.
  <os>
    <type arch='ppc' machine='ppce500v2'>hvm</type>
    <kernel>/media/ram/uImage</kernel>
    <initrd>/media/ram/ramdisk</initrd>
    <dtb>/media/ram/test.dtb</dtb>
    <cmdline>root=/dev/ram rw console=ttyS0,115200</cmdline>
  </os>
Signed-off-by: NEric Blake <eblake@redhat.com>