Currently each USB2 companion controller gets put on a separate
PCI slot. Not only is this wasteful of PCI slots, but it is not
in compliance with the spec for USB2 controllers. The master
echi1 and all companion controllers should be in the same slot,
with echi1 in function 7, and uhci1-3 in functions 0-2 respectively.

* src/qemu/qemu_command.c: Special case handling of USB2 controllers
  to apply correct pci slot assignment
* tests/qemuxml2argvdata/qemuxml2argv-usb-ich9-ehci-addr.args,
  tests/qemuxml2argvdata/qemuxml2argv-usb-ich9-ehci-addr.xml: Expand
  test to cover automatic slot assignment
(cherry picked from commit 1ebd52cb)

Conflicts:

	tests/qemuxml2xmltest.c

The virDomainDeviceInfoIsSet API was only checking if an
address or alias was set in the struct. Thus if only a
rom bar setting / filename, boot index, or USB master
value was set, they could be accidentally dropped when
formatting XML
(cherry picked from commit 2c195fdb)

Sometimes it is useful to see the callpath for log messages.
This change enhances the log filter syntax so that stack traces
can be show by setting '1:+NAME' instead of '1:NAME'.

This results in output like:

2012-05-09 14:18:45.136+0000: 13314: debug : virInitialize:414 : register drivers
/home/berrange/src/virt/libvirt/src/.libs/libvirt.so.0(virInitialize+0xd6)[0x7f89188ebe86]
/home/berrange/src/virt/libvirt/tools/.libs/lt-virsh[0x431921]
/lib64/libc.so.6(__libc_start_main+0xf5)[0x3a21e21735]
/home/berrange/src/virt/libvirt/tools/.libs/lt-virsh[0x40a279]

2012-05-09 14:18:45.136+0000: 13314: debug : virRegisterDriver:775 : driver=0x7f8918d02760 name=Test
/home/berrange/src/virt/libvirt/src/.libs/libvirt.so.0(virRegisterDriver+0x6b)[0x7f89188ec717]
/home/berrange/src/virt/libvirt/src/.libs/libvirt.so.0(+0x11b3ad)[0x7f891891e3ad]
/home/berrange/src/virt/libvirt/src/.libs/libvirt.so.0(virInitialize+0xf3)[0x7f89188ebea3]
/home/berrange/src/virt/libvirt/tools/.libs/lt-virsh[0x431921]
/lib64/libc.so.6(__libc_start_main+0xf5)[0x3a21e21735]
/home/berrange/src/virt/libvirt/tools/.libs/lt-virsh[0x40a279]

* docs/logging.html.in: Document new syntax
* configure.ac: Check for execinfo.h
* src/util/logging.c, src/util/logging.h: Add support for
  stack traces
* tests/testutils.c: Adapt to API change
Signed-off-by: NDaniel P. Berrange <berrange@redhat.com>
(cherry picked from commit 54856395)

According to Fedora guidelines, because we bundle gnulib we
need to add a virtual Provides: bundled(gnulib).

https://fedoraproject.org/wiki/Packaging:No_Bundled_Libraries#Requirement_if_you_bundle
(cherry picked from commit 3247b63b)

$LISTFILE is created even no domain is running, and the empty
$LISTFILE could cause improper service status.

    stopped ,with saved guests

Which is not right, as there is no domain was saved.
(cherry picked from commit c086af6b)

On some of the NUMA platforms, the CPU index in each NUMA node
grows non-consecutive. While on other platforms, it can be inconsecutive,
E.g.

% numactl --hardware
available: 4 nodes (0-3)
node 0 cpus: 0 4 8 12 16 20 24 28
node 0 size: 131058 MB
node 0 free: 86531 MB
node 1 cpus: 1 5 9 13 17 21 25 29
node 1 size: 131072 MB
node 1 free: 127070 MB
node 2 cpus: 2 6 10 14 18 22 26 30
node 2 size: 131072 MB
node 2 free: 127758 MB
node 3 cpus: 3 7 11 15 19 23 27 31
node 3 size: 131072 MB
node 3 free: 127226 MB
node distances:
node   0   1   2   3
  0:  10  20  20  20
  1:  20  10  20  20
  2:  20  20  10  20
  3:  20  20  20  10

This patch is to fix the problem by using the CPU index in
caps->host.numaCell[i]->cpus[i] to set the bitmask instead of
assuming the CPU index of the NUMA nodes are always sequential.
(cherry picked from commit d1bdeca8)

For pseries guest, the default controller model is
ibmvscsi controller, this controller only can work
on spapr-vio address.

This patch is to assign spapr-vio address type to
ibmvscsi controller and correct vscsi test case.
Signed-off-by: NLi Zhang <zhlcindy@linux.vnet.ibm.com>
(cherry picked from commit bb725ac1)

Appending an item to a list transfers ownership of that item to the
list owner. But an error can occur in between item allocation and
appending it to the list. In this case the item has to be freed
explicitly. This was not done in some special cases resulting in
possible memory leaks.

Reported by Coverity.
(cherry picked from commit 3b9a1295)

This patch lifts the limit of calling thread detection code only on KVM
guests. With upstream qemu the thread mappings are reported also on
non-KVM machines.

QEMU adopted the thread_id information from the kvm branch.

To remain compatible with older upstream versions of qemu the check is
attempted but the failure to detect threads (or even run the monitor
command - on older versions without SMP support) is treated non-fatal
and the code reports one vCPU with pid of the hypervisor (in same
fashion this was done on non-KVM guests).
(cherry picked from commit c8335269)

After a cpu hotplug the qemu driver did not refresh information about
virtual processors used by qemu and their corresponding threads. This
patch forces a re-detection as is done on start of QEMU.

This ensures that correct information is reported by the
virDomainGetVcpus API and "virsh vcpuinfo".

A failure to obtain the thread<->vcpu mapping is treated non-fatal and
the mapping is not updated in a case of failure as not all versions of
QEMU report this in the info cpus command.
(cherry picked from commit 3163682b)

This patch changes a switch statement into ifs when handling live vs.
configuration modifications getting rid of redundant code in case when
both live and persistent configuration gets changed.
(cherry picked from commit e99ad93d)

when failing to attach another usb device to a domain for some reason
which has one use device attached before, the libvirtd crashed.
The crash is caused by null-pointer dereference error in invoking
usbDeviceListSteal passed in NULL value usb variable.
commit 05abd150 introduces the bug.
(cherry picked from commit ab5fb8f3)

Based on a report by Seth Vidal.  Just because _you_ can use virsh
to connect to both source and destinations does not mean that libvirtd
on the source (aka _root_) can likewise connect to the destination;
this matters when setting up a peer-to-peer migration instead of a
native one.

* docs/migration.html.in: Mention that in peer-to-peer, the owner
of the source libvirtd (usually root) must be able to connect to
the destination.
(cherry picked from commit 38bd605b)

s/nuamd/numad/,
(cherry picked from commit eecee94c)

Commit 97010eb1 forgot to change the other side of an #ifdef.

* src/qemu/qemu_process.c (qemuProcessInitNumaMemoryPolicy): Add
argument.
(cherry picked from commit 5c650b98)

No useful error was being reported when an invalid character device
target type is specified in the domainXML. E.g.

    ...
    <console type="pty">
      <source path="/dev/pts/2"/>
      <target type="kvm" port="0"/>
    </console>
    ...

resulted in

error: Failed to define domain from x.xml
error: An error occurred, but the cause is unknown

With this small patch, the error is more helpful

error: Failed to define domain from x.xml
error: XML error: unknown target type 'kvm' specified for character device
(cherry picked from commit 10a87145)

Not only support CPU placement now.
(cherry picked from commit b736e722)

Since now we pre-set memory policy using libnuma to fully
drive numad, it needs to check numactl-devel if "with_numad"
is "yes".

configure with groups "--with-numad=yes --with-numactl=yes",
"--with-numad=no --with-numactl=yes", "--with-numad=yes
--with-numactl=yes" works fine after the change.
(cherry picked from commit b0f32445)

It turns out that when cgroups are enabled, the use of a block device
for a snapshot target was failing with EPERM due to libvirt failing
to add the block device to the cgroup whitelist.  See also
https://bugzilla.redhat.com/show_bug.cgi?id=810200

* src/qemu/qemu_driver.c
(qemuDomainSnapshotCreateSingleDiskActive)
(qemuDomainSnapshotUndoSingleDiskActive): Account for cgroup.
(qemuDomainSnapshotCreateDiskActive): Update caller.
(cherry picked from commit 8be304ec)

Alon tried './qemuxml2argvtest --help' to figure out a test failure,
but it didn't help.  The information is in HACKING, but it doesn't
hurt to make the tests also provide their own help.
Signed-off-by: NAlon Levy <alevy@redhat.com>
Signed-off-by: NEric Blake <eblake@redhat.com>
(cherry picked from commit 75d155ec)

We only know -lpthread exists on platforms where we build
threads-pthread.c; but when we build threads-win32.c, LIB_PTHREAD
is empty.

* tests/Makefile.am (shunloadtest_LDADD): Use correct library.
(cherry picked from commit 0ca336b3)

* tools/virsh.c (vshParseSnapshotDiskspec): Fix off-by-3 memmove
that would corrupt heap when parsing escaped --diskspec comma.
Bug introduced via commit v0.9.4-260-g35d52b56.
(cherry picked from commit c6694ab8)

Until now, the nl_pid of the source address of every message sent by
virNetlinkCommand has been set to the value of getpid(). Most of the
time this doesn't matter, and in the one case where it does
(communication with lldpad), it previously was the proper thing to do,
because the netlink event service (which listens on a netlink socket
for unsolicited messages from lldpad) coincidentally always happened
to bind with a local nl_pid == getpid().

With the fix for:

  https://bugzilla.redhat.com/show_bug.cgi?id=816465

that particular nl_pid is now effectively a reserved value, so the
netlink event service will always bind to something else
(coincidentally "getpid() + (1 << 22)", but it really could be
anything). The result is that communication between lldpad and
libvirtd is broken (lldpad gets a "disconnected" error when it tries
to send a directed message).

The solution to this problem caused by a solution, is to query the
netlink event service's nlhandle for its "local_port", and send that
as the source nl_pid (but only when sending to lldpad, of course - in
other cases we maintain the old behavior of sending getpid()).

There are two cases where a message is being directed at lldpad - one
in virNetDevLinkDump, and one in virNetDevVPortProfileOpSetLink.

The case of virNetDevVPortProfileOpSetLink is simplest to explain -
only if !nltarget_kernel, i.e. the message isn't targetted for the
kernel, is the dst_pid set (by calling
virNetDevVPortProfileGetLldpadPid()), so only in that case do we call
virNetlinkEventServiceLocalPid() to set src_pid.

For virNetDevLinkDump, it's a bit more complicated. The call to
virNetDevVPortProfileGetLldpadPid() was effectively up one level (in
virNetDevVPortProfileOpCommon), although obscured by an unnecessary
passing of a function pointer. This patch removes the function
pointer, and calls virNetDevVPortProfileGetLldpadPid() directly in
virNetDevVPortProfileOpCommon - if it's doing this, it knows that it
should also call virNetlinkEventServiceLocalPid() to set src_pid too;
then it just passes src_pid and dst_pid down to
virNetDevLinkDump. Since (src_pid == 0 && dst_pid == 0) implies that
the kernel is the destination, there is no longer any need to send
nltarget_kernel as an arg to virNetDevLinkDump, so it's been removed.

The disparity between src_pid being int and dst_pid being uint32_t may
be a bit disconcerting to some, but I didn't want to complicate
virNetlinkEventServiceLocalPid() by having status returned separately
from the value.
(cherry picked from commit cc073771)

This value will be needed to set the src_pid when sending netlink
messages to lldpad. It is part of the solution to:

  https://bugzilla.redhat.com/show_bug.cgi?id=816465

Note that libnl's port generation algorithm guarantees that the
nl_socket_get_local_port() will always be > 0 (since it is "getpid() +
(n << 22>" where n is always < 1024), so it is okay to cast the
uint32_t to int (thus allowing us to use -1 as an error sentinel).
(cherry picked from commit c99e9375)

Until now, virNetlinkCommand has assumed that the nl_pid in the source
address of outgoing netlink messages should always be the return value
of getpid(). In most cases it actually doesn't matter, but in the case
of communication with lldpad, lldpad saves this info and later uses it
to send netlink messages back to libvirt. A recent patch to fix Bug
816465 changed the order of the universe such that the netlink event
service socket is no longer bound with nl_pid == getpid(), so lldpad
could no longer send unsolicited messages to libvirtd. Adding src_pid
as an argument to virNetlinkCommand() is the first step in notifying
lldpad of the proper address of the netlink event service socket.
(cherry picked from commit cca7bb1f)

This is part of the solution to the problem detailed in:

  https://bugzilla.redhat.com/show_bug.cgi?id=816465

and further detailed in

  https://www.redhat.com/archives/libvir-list/2012-May/msg00202.htm

A short explanation is included in the comments of the patch itself.

Note that this patch by itself breaks communication between lldpad and
libvirtd, so the other 3 patches in the series must be applied at the
same time as this patch.
(cherry picked from commit 64297313)

Conflicts:

	daemon/libvirtd.c

src/qemu/qemu_hostdev.c:
refactor qemuPrepareHostdevUSBDevices function, make it focus on
adding usb device to activeUsbHostdevs after check. After that,
the usb hotplug function qemuDomainAttachHostDevice also could use
it.
expand qemuPrepareHostUSBDevices to perform the usb search,
rollback on failure.

src/qemu/qemu_hotplug.c:
If there are multiple usb devices available with same vendorID and productID,
but with different value of "bus, device", we give an error to let user
use <address> to specify the desired one.
(cherry picked from commit 05abd150)

usbFindDevice():get usb device according to
                idVendor, idProduct, bus, device
                it is the exact match of the four parameters

usbFindDeviceByBus():get usb device according to bus, device
                  it returns only one usb device same as usbFindDevice

usbFindDeviceByVendor():get usb device according to idVendor,idProduct
                     it probably returns multiple usb devices.

usbDeviceSearch(): a helper function to do the actual search
(cherry picked from commit 9914477e)

(cherry picked from commit f4345ac2)

Conflicts:

	libvirt.spec.in

When we added the default USB controller into domain XML, we efficiently
broke migration to older versions of libvirt that didn't support USB
controllers at all (0.9.4 and earlier) even for domains that don't use
anything that the older libvirt can't provide. We still want to present
the default USB controller in any XML seen by a user/app but we can
safely remove it from the domain XML used during migration. If we are
migrating to a new enough libvirt, it will add the controller XML back,
while older libvirt won't be confused with it although it will still
tell qemu to create the controller.

Similar approach can be used in the future whenever we find out we
always enabled some kind of device without properly advertising it in
domain XML.
(cherry picked from commit 409b5f54)

Always use appropriate qemuDomain{,Def}Format wrapper since it may do
some additional magic based on the flags.
(cherry picked from commit cd603008)

Commit 4c82f09e added a capability check for qemu per-device io
throttling, but only applied it to domain startup.  As mentioned
in the previous commit (98cec052), the user can still get an 'internal
error' message during a hotplug attempt, when the monitor command
doesn't exist.  It is confusing to allow tuning on inactive domains
only to then be rejected when starting the domain.

* src/qemu/qemu_driver.c (qemuDomainSetBlockIoTune): Reject
offline tuning if online can't match it.
(cherry picked from commit 13f9a193)

If you have a qemu build that lacks the blockio tune monitor command,
then this command:

$ virsh blkdeviotune rhel6u2 hda --total_bytes_sec 1000
error: Unable to change block I/O throttle
error: internal error Unexpected error

fails as expected (well, the error message is lousy), but the next
dumpxml shows that the domain was modified anyway.  Worse, that means
if you save the domain then restore it, the restore will likely fail
due to throttling being unsupported, even though no throttling should
even be active because the monitor command failed in the first place.

* src/qemu/qemu_driver.c (qemuDomainSetBlockIoTune): Check for
error before making modification permanent.
(cherry picked from commit 98cec052)

These two functions are called from main() on all platforms, and
always return success on platforms that don't support libnl. They
still log an error message, though, which doesn't make sense - they
should just be NOPs on those platforms. (Per a suggestion during
review, I've turned the logs into debug messages rather than removing
them completely).
(cherry picked from commit bae4ff28)

Error: STRING_NULL:
/libvirt/src/node_device/node_device_linux_sysfs.c:80:
string_null_argument: Function "saferead" does not terminate string "*buf".
/libvirt/src/util/util.c:101:
string_null_argument: Function "read" fills array "*buf" with a non-terminated string.
/libvirt/src/node_device/node_device_linux_sysfs.c:87:
string_null: Passing unterminated string "buf" to a function expecting a null-terminated string.

(cherry picked from commit 43d1616f)

Error: STRING_NULL:
/libvirt/src/util/uuid.c:273:
string_null_argument: Function "getDMISystemUUID" does not terminate string "*dmiuuid".
/libvirt/src/util/uuid.c:241:
string_null_argument: Function "saferead" fills array "*uuid" with a non-terminated string.
/libvirt/src/util/util.c:101:
string_null_argument: Function "read" fills array "*buf" with a non-terminated string.
/libvirt/src/util/uuid.c:274:
string_null: Passing unterminated string "dmiuuid" to a function expecting a null-terminated string.
/libvirt/src/util/uuid.c:138:
var_assign_parm: Assigning: "cur" = "uuidstr". They now point to the same thing.
/libvirt/src/util/uuid.c:164:
string_null_sink_loop: Searching for null termination in an unterminated array "cur".

(cherry picked from commit b4586051)

Error: RESOURCE_LEAK:
/libvirt/tests/qemuxml2argvtest.c:47:
alloc_arg: Calling allocation function "virAlloc" on "ret".
/libvirt/src/util/memory.c:101:
alloc_fn: Storage is returned from allocation function "calloc".
/libvirt/src/util/memory.c:101:
var_assign: Assigning: "*((void **)ptrptr)" = "calloc(1UL, size)".
/libvirt/tests/qemuxml2argvtest.c:54:
leaked_storage: Variable "ret" going out of scope leaks the storage it points to.

(cherry picked from commit a01e6721)

Error: RESOURCE_LEAK:
/libvirt/src/qemu/qemu_driver.c:6968:
alloc_fn: Calling allocation function "calloc".
/libvirt/src/qemu/qemu_driver.c:6968:
var_assign: Assigning: "nodeset" =  storage returned from "calloc(1UL, 1UL)".
/libvirt/src/qemu/qemu_driver.c:6977:
noescape: Variable "nodeset" is not freed or pointed-to in function "virTypedParameterAssign".
/libvirt/src/qemu/qemu_driver.c:6997:
leaked_storage: Variable "nodeset" going out of scope leaks the storage it points to.

(cherry picked from commit c0774482)

Error: RESOURCE_LEAK:
/libvirt/src/vmx/vmx.c:2431:
alloc_fn: Calling allocation function "calloc".
/libvirt/src/vmx/vmx.c:2431:
var_assign: Assigning: "networkName" =  storage returned from "calloc(1UL, 1UL)".
/libvirt/src/vmx/vmx.c:2495:
leaked_storage: Variable "networkName" going out of scope leaks the storage it points to.

(cherry picked from commit 409a637e)

(cherry picked from commit fd2b4157)