提交 6bf28f38 编写于 作者: J John Ferlan

docs: Add more iscsi-direct references to storage pages

Found that it was missing in formatstorage and had a few typos
in the storage driver page.
Signed-off-by: NJohn Ferlan <jferlan@redhat.com>
Reviewed-by: NCole Robinson <crobinso@redhat.com>
上级 d2edbec2
......@@ -19,14 +19,15 @@
a single attribute <code>type</code>, which is one of <code>dir</code>,
<code>fs</code>, <code>netfs</code>, <code>disk</code>,
<code>iscsi</code>, <code>logical</code>, <code>scsi</code>
(all <span class="since">since 0.4.1</span>), <code>mpath</code>
(<span class="since">since 0.7.1</span>), <code>rbd</code>
(<span class="since">since 0.9.13</span>), <code>sheepdog</code>
(<span class="since">since 0.10.0</span>),
<code>gluster</code> (<span class="since">since
1.2.0</span>), <code>zfs</code> (<span class="since">since
1.2.8</span>) or <code>vstorage</code> (<span class="since">since
3.1.0</span>). This corresponds to the
(all <span class="since">since 0.4.1</span>),
<code>mpath</code> (<span class="since">since 0.7.1</span>),
<code>rbd</code> (<span class="since">since 0.9.13</span>),
<code>sheepdog</code> (<span class="since">since 0.10.0</span>),
<code>gluster</code> (<span class="since">since 1.2.0</span>),
<code>zfs</code> (<span class="since">since 1.2.8</span>),
<code>vstorage</code> (<span class="since">since 3.1.0</span>),
or <code>iscsi-direct</code> (<span class="since">since 4.7.0</span>).
This corresponds to the
storage backend drivers listed further along in this document.
</p>
<h3><a id="StoragePoolFirst">General metadata</a></h3>
......@@ -125,11 +126,12 @@
<dt><code>device</code></dt>
<dd>Provides the source for pools backed by physical devices
(pool types <code>fs</code>, <code>logical</code>, <code>disk</code>,
<code>iscsi</code>, <code>zfs</code>, <code>vstorage</code>).
<code>iscsi</code>, <code>iscsi-direct</code>, <code>zfs</code>,
<code>vstorage</code>).
May be repeated multiple times depending on backend driver. Contains
a required attribute <code>path</code> which is either the fully
qualified path to the block device node or for <code>iscsi</code>
the iSCSI Qualified Name (IQN).
or <code>iscsi-direct</code> the iSCSI Qualified Name (IQN).
<span class="since">Since 0.4.1</span>
<p>An optional attribute <code>part_separator</code> for each
<code>path</code> may be supplied. Valid values for the attribute
......@@ -334,6 +336,7 @@
<dt><code>host</code></dt>
<dd>Provides the source for pools backed by storage from a
remote server (pool types <code>netfs</code>, <code>iscsi</code>,
<code>iscsi-direct</code>,
<code>rbd</code>, <code>sheepdog</code>, <code>gluster</code>). Will be
used in combination with a <code>directory</code>
or <code>device</code> element. Contains an attribute <code>name</code>
......@@ -348,11 +351,19 @@
server. See the <a href="storage.html">storage driver page</a> for
any restrictions for specific storage backends.
<span class="since">Since 0.4.1</span></dd>
<dt><code>initiator</code></dt>
<dd>Required by the <code>iscsi-direct</code> pool in order to provide
the iSCSI Qualified Name (IQN) to communicate with the pool's
<code>device</code> target IQN. There is one sub-element
<code>iqn</code> with the <code>name</code> attribute to describe
the IQN for the initiator.
<span class="since">Since 4.7.0</span></dd>
<dt><code>auth</code></dt>
<dd>If present, the <code>auth</code> element provides the
authentication credentials needed to access the source by the
setting of the <code>type</code> attribute (pool
types <code>iscsi</code>, <code>rbd</code>). The <code>type</code>
types <code>iscsi</code>, <code>iscsi-direct</code>, <code>rbd</code>).
The <code>type</code>
must be either "chap" or "ceph". Use "ceph" for
Ceph RBD (Rados Block Device) network sources and use "iscsi" for CHAP
(Challenge-Handshake Authentication Protocol) iSCSI
......
......@@ -437,9 +437,9 @@
<h2><a id="StorageBackendISCSIDirect">iSCSI direct pool</a></h2>
<p>
This is a variant of the iSCSI pool. Instead of unsing iscsiadm, it uses
This is a variant of the iSCSI pool. Instead of using iscsiadm, it uses
libiscsi.
It require a host, a path which is the target iqn and an initiator iqn.
It requires a host, a path which is the target IQN, and an initiator IQN.
</p>
<h3>Example pool input</h3>
......@@ -457,12 +457,12 @@
<h3>Valid pool format types</h3>
<p>
The iSCSI volume pool does not use the pool format type element.
The iSCSI direct volume pool does not use the pool format type element.
</p>
<h3>Valid volume format types</h3>
<p>
The iSCSI volume pool does not use the volume format type element.
The iSCSI direct volume pool does not use the volume format type element.
</p>
<h2><a id="StorageBackendSCSI">SCSI pool</a></h2>
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册