This patch allow users to dump content of NCL_CONFIG by using debugfs
command.
Command format:
	echo dump ncl_config <offset> <length> > cmd
It will print as follows:
	hns3 0000:7d:00.0: offset |    data
	hns3 0000:7d:00.0: 0x0000 | 0x00000020
	hns3 0000:7d:00.0: 0x0004 | 0x00000400
	hns3 0000:7d:00.0: 0x0008 | 0x08020401
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for network interface message level
settings. The message level can be changed by module parameter
or ethtool.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function hns3_get_tx_timeo_queue_info(), it should use
netdev->num_tx_queues, instead of netdve->real_num_tx_queues
as the loop limitation.

Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In current codes, tx_timeout_cnt is used before increased,
then we can see the tx_timeout_count is still 0 from the
print when tx timeout happens, e.g.
"hns3 0000:7d:00.3 eth3: tx_timeout count: 0, queue id: 0, SW_NTU:
 0xa6, SW_NTC: 0xa4, HW_HEAD: 0xa4, HW_TAIL: 0xa6, INT: 0x1"

The tx_timeout_cnt should be updated before used.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When wait for response timeout or response code not match, there
should be more information for debugging.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When received vector0 msix and other event interrupt, it should
print the value of the register for debugging.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some statistics for VF reset.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).

So this patch fixes it by using u32 for vport->bw_limit.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The input parameter "proto" in function hclge_set_vlan_filter_hw()
is asked to be __be16, but got u16 when calling it in function
hclge_update_port_base_vlan_cfg().

This patch fixes it by converting it with htons().
Reported-by: Nkbuild test robot <lkp@intel.com>
Fixes: 21e043cd ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some redundant BH disable when initializing
and uninitializing command queue.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there is pending skb in RX flow when close the port, and the
pending buffer is not cleaned, the new packet will be added to
the pending skb when the port opens again, and the first new
packet has error data.

This patch cleans the pending skb when clean RX ring.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some cases, PHY may not be connected to MDIO bus, then
the driver will initialize fail since MDIO bus initialization
fails.

This patch fixes it by skipping the MDIO bus initialization
when PHY is inexistent.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to hardware description, reset level that should be
triggered are not consistent in a module. For example, in SSU
common errors, the first two bits has no need to do reset,
but the other bits need global reset.

This patch sets separate reset level for all RAS and MSI-X
interrupts by adding a reset_lvel field in struct hclge_hw_error,
and fixes some incorrect reset level.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently hardware may have not enough buffer to receive packet
when it has used more than two MPS(maximum packet size) of
buffer, but there are still a lot of shared buffer left unused
when TC num is small.

This patch divides shared buffer to be used between TC when
the port supports DCB, and adjusts the waterline and threshold
according to user manual for the port that does not support
DCB.

This patch also change hclge_get_tc_num's return type to u32
to avoid signed-unsigned mix with divide.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently RX shared buffer' threshold size for speific TC is
set to smaller value when the TC's PFC is not enabled, which may
cause performance problem because hardware may not have enough
hardware buffer when PFC is not enabled.

This patch sets the same threshold size for all TC no matter if
the specific TC's PFC is enabled.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a GRO packet is received by driver, the cwr field in the
struct tcphdr needs to be checked to decide whether to set the
SKB_GSO_TCP_ECN for skb_shinfo(skb)->gso_type.

So this patch adds hns3_gro_complete to do that, and adds the
hns3_handle_bdinfo to handle the hns3_gro_complete and
hns3_rx_checksum.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the parameters of hns3_rx_checksum to be more specific to
what is used internally, rather than passing in a pointer to the
whole hns3_desc. Reduces duplicate code and bring this function
inline with the approach used in hns3_set_gro_param.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.

This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.

Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.

This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, in TX direction, driver implements the TX VLAN offload
by checking the VLAN header in skb, and filling it into TX descriptor.
Usually it works well, but if enable inserting VLAN header based on
port, it may conflict when out_tag field of TX descriptor is already
used, and cause RAS error.

In RX direction, hardware supports stripping max two VLAN headers.
For vlan_tci in skb can only store one VLAN tag, when RX VLAN offload
enabled, driver tells hardware to strip one VLAN header from RX
packet; when RX VLAN offload disabled, driver tells hardware not to
strip VLAN header from RX packet. Now if port based insert VLAN
enabled, all RX packets will have the port based VLAN header. This
header is useless for stack, driver needs to ask hardware to strip
it. Unfortunately, hardware can't drop this VLAN header, and always
fill it into RX descriptor, so driver has to identify and drop it.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf  <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack.  In this case, driver needs to tell
hardware which VLAN to insert or strip.

The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hclgevf_client_start() fails or VF driver unloaded, there is
nobody to disable keep_alive_timer.

So this patch fixes them.

Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The checking of HCLGEVF_STATE_RST_HANDLING flag in the
hclgevf_reset_task_schedule() will make some scheduling of
reset pending fail. This flag will be checked in the
hclgevf_reset_service_task(), it is unnecessary to check it
in the hclgevf_reset_task_schedule(). So this patch removes it.

Fixes: 35a1e503 ("net: hns3: Add VF Reset Service Task to support event handling")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds error handler for the failure of command queue
initialization both PF and VF.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the command queue needs re-initialization, the mailbox handling
task should do nothing, otherwise this task will just get some error
print.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ongoing lower-level reset will fail when there is a higher-level
reset occurs, so the error handler should deal with this situation.

Fixes: 6a5f6fa3 ("net: hns3: add error handler for hclgevf_reset()")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hardware reset does not finish, the driver should not
request a new reset, otherwise the ongoing hardware reset
will get problem.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is unnecessary to deal with the new coming reset if
it is lower than the ongoing one.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the reset has been done successfully, the ongoing reset timer
is unnecessary.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_client_stop() should be called after unregister_netdev(),
otherwise the ongoing reset task may start the client just after it.

Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a vport is not alive, it is unnecessary to notify it to reset
before PF asserting a reset. So before inform vport to reset,
we need to check its alive state firstly.

Fixes: aa5c4f17 ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reinitializing, the vport alive state needs to be set up.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When resetting, the vport alive state should be set to default,
otherwise the alive state of the vport whose driver not running
is wrong before the timer to check it out.

Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mskid is unsigned and hence comparisons with negative
error return values are always false. Fix this by making mskid an
int.

Fixes: f058e468 ("net: hns: fix ICMP6 neighbor solicitation messages discard problem")
Addresses-Coverity: ("Operands don't affect result")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some sparse warnings in the HNS drivers:

warning: incorrect type in assignment (different address spaces)
    expected void [noderef] <asn:2> *io_base
    got void *vaddr
warning: cast removes address space '<asn:2>' of expression
[...]

Add __iomem and change all the u8 __iomem to void __iomem to
fix these kind of  warnings.

warning: incorrect type in argument 1 (different address spaces)
    expected void [noderef] <asn:2> *base
    got unsigned char [usertype] *base_addr
warning: cast to restricted __le16
warning: incorrect type in assignment (different base types)
    expected unsigned int [usertype] tbl_tcam_data_high
    got restricted __le32 [usertype]
warning: cast to restricted __le32
[...]

These variables used u32/u16 as their type, and finally as a
parameter of writel(), writel() will do the cpu_to_le32 coversion
so remove the little endian covert code to fix these kind of warnings.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enable SMMU, remove HNS driver will cause a WARNING:

[  141.924177] WARNING: CPU: 36 PID: 2708 at drivers/iommu/dma-iommu.c:443 __iommu_dma_unmap+0xc0/0xc8
[  141.954673] Modules linked in: hns_enet_drv(-)
[  141.963615] CPU: 36 PID: 2708 Comm: rmmod Tainted: G        W         5.0.0-rc1-28723-gb729c57de95c-dirty #32
[  141.983593] Hardware name: Huawei D05/D05, BIOS Hisilicon D05 UEFI Nemo 1.8 RC0 08/31/2017
[  142.000244] pstate: 60000005 (nZCv daif -PAN -UAO)
[  142.009886] pc : __iommu_dma_unmap+0xc0/0xc8
[  142.018476] lr : __iommu_dma_unmap+0xc0/0xc8
[  142.027066] sp : ffff000013533b90
[  142.033728] x29: ffff000013533b90 x28: ffff8013e6983600
[  142.044420] x27: 0000000000000000 x26: 0000000000000000
[  142.055113] x25: 0000000056000000 x24: 0000000000000015
[  142.065806] x23: 0000000000000028 x22: ffff8013e66eee68
[  142.076499] x21: ffff8013db919800 x20: 0000ffffefbff000
[  142.087192] x19: 0000000000001000 x18: 0000000000000007
[  142.097885] x17: 000000000000000e x16: 0000000000000001
[  142.108578] x15: 0000000000000019 x14: 363139343a70616d
[  142.119270] x13: 6e75656761705f67 x12: 0000000000000000
[  142.129963] x11: 00000000ffffffff x10: 0000000000000006
[  142.140656] x9 : 1346c1aa88093500 x8 : ffff0000114de4e0
[  142.151349] x7 : 6662666578303d72 x6 : ffff0000105ffec8
[  142.162042] x5 : 0000000000000000 x4 : 0000000000000000
[  142.172734] x3 : 00000000ffffffff x2 : ffff0000114de500
[  142.183427] x1 : 0000000000000000 x0 : 0000000000000035
[  142.194120] Call trace:
[  142.199030]  __iommu_dma_unmap+0xc0/0xc8
[  142.206920]  iommu_dma_unmap_page+0x20/0x28
[  142.215335]  __iommu_unmap_page+0x40/0x60
[  142.223399]  hnae_unmap_buffer+0x110/0x134
[  142.231639]  hnae_free_desc+0x6c/0x10c
[  142.239177]  hnae_fini_ring+0x14/0x34
[  142.246540]  hnae_fini_queue+0x2c/0x40
[  142.254080]  hnae_put_handle+0x38/0xcc
[  142.261619]  hns_nic_dev_remove+0x54/0xfc [hns_enet_drv]
[  142.272312]  platform_drv_remove+0x24/0x64
[  142.280552]  device_release_driver_internal+0x17c/0x20c
[  142.291070]  driver_detach+0x4c/0x90
[  142.298259]  bus_remove_driver+0x5c/0xd8
[  142.306148]  driver_unregister+0x2c/0x54
[  142.314037]  platform_driver_unregister+0x10/0x18
[  142.323505]  hns_nic_dev_driver_exit+0x14/0xf0c [hns_enet_drv]
[  142.335248]  __arm64_sys_delete_module+0x214/0x25c
[  142.344891]  el0_svc_common+0xb0/0x10c
[  142.352430]  el0_svc_handler+0x24/0x80
[  142.359968]  el0_svc+0x8/0x7c0
[  142.366104] ---[ end trace 60ad1cd58e63c407 ]---

The tx ring buffer map when xmit and unmap when xmit done. So in
hnae_init_ring() did not map tx ring buffer, but in hnae_fini_ring()
have a unmap operation for tx ring buffer, which is already unmapped
when xmit done, than cause this WARNING.

The hnae_alloc_buffers() is called in hnae_init_ring(),
so the hnae_free_buffers() should be in hnae_fini_ring(), not in
hnae_free_desc().

In hnae_fini_ring(), adds a check is_rx_ring() as in hnae_init_ring().
When the ring buffer is tx ring, adds a piece of code to ensure that
the tx ring is unmap.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.

This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reboot the system again and again, may cause a memory
overwrite.

[   15.638922] systemd[1]: Reached target Swap.
[   15.667561] tun: Universal TUN/TAP device driver, 1.6
[   15.676756] Bridge firewalling registered
[   17.344135] Unable to handle kernel paging request at virtual address 0000000200000040
[   17.352179] Mem abort info:
[   17.355007]   ESR = 0x96000004
[   17.358105]   Exception class = DABT (current EL), IL = 32 bits
[   17.364112]   SET = 0, FnV = 0
[   17.367209]   EA = 0, S1PTW = 0
[   17.370393] Data abort info:
[   17.373315]   ISV = 0, ISS = 0x00000004
[   17.377206]   CM = 0, WnR = 0
[   17.380214] user pgtable: 4k pages, 48-bit VAs, pgdp = (____ptrval____)
[   17.386926] [0000000200000040] pgd=0000000000000000
[   17.391878] Internal error: Oops: 96000004 [#1] SMP
[   17.396824] CPU: 23 PID: 95 Comm: kworker/u130:0 Tainted: G            E     4.19.25-1.2.78.aarch64 #1
[   17.414175] Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.54 08/16/2018
[   17.425615] Workqueue: events_unbound async_run_entry_fn
[   17.435151] pstate: 00000005 (nzcv daif -PAN -UAO)
[   17.444139] pc : __mutex_lock.isra.1+0x74/0x540
[   17.453002] lr : __mutex_lock.isra.1+0x3c/0x540
[   17.461701] sp : ffff000100d9bb60
[   17.469146] x29: ffff000100d9bb60 x28: 0000000000000000
[   17.478547] x27: 0000000000000000 x26: ffff802fb8945000
[   17.488063] x25: 0000000000000000 x24: ffff802fa32081a8
[   17.497381] x23: 0000000000000002 x22: ffff801fa2b15220
[   17.506701] x21: ffff000009809000 x20: ffff802fa23a0888
[   17.515980] x19: ffff801fa2b15220 x18: 0000000000000000
[   17.525272] x17: 0000000200000000 x16: 0000000200000000
[   17.534511] x15: 0000000000000000 x14: 0000000000000000
[   17.543652] x13: ffff000008d95db8 x12: 000000000000000d
[   17.552780] x11: ffff000008d95d90 x10: 0000000000000b00
[   17.561819] x9 : ffff000100d9bb90 x8 : ffff802fb89d6560
[   17.570829] x7 : 0000000000000004 x6 : 00000004a1801d05
[   17.579839] x5 : 0000000000000000 x4 : 0000000000000000
[   17.588852] x3 : ffff802fb89d5a00 x2 : 0000000000000000
[   17.597734] x1 : 0000000200000000 x0 : 0000000200000000
[   17.606631] Process kworker/u130:0 (pid: 95, stack limit = 0x(____ptrval____))
[   17.617438] Call trace:
[   17.623349]  __mutex_lock.isra.1+0x74/0x540
[   17.630927]  __mutex_lock_slowpath+0x24/0x30
[   17.638602]  mutex_lock+0x50/0x60
[   17.645295]  drain_workqueue+0x34/0x198
[   17.652623]  __sas_drain_work+0x7c/0x168
[   17.659903]  sas_drain_work+0x60/0x68
[   17.666947]  hisi_sas_scan_finished+0x30/0x40 [hisi_sas_main]
[   17.676129]  do_scsi_scan_host+0x70/0xb0
[   17.683534]  do_scan_async+0x20/0x228
[   17.690586]  async_run_entry_fn+0x4c/0x1d0
[   17.697997]  process_one_work+0x1b4/0x3f8
[   17.705296]  worker_thread+0x54/0x470

Every time the call trace is not the same, but the overwrite address
is always the same:
Unable to handle kernel paging request at virtual address 0000000200000040

The root cause is, when write the reg XGMAC_MAC_TX_LF_RF_CONTROL_REG,
didn't use the io_base offset.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>