Allocate CPU rmap and add entry for each irq. CPU rmap is
used in aRFS to get the queue number of the rx completion
interrupts.

In additional, remove the calling of
irq_set_affinity_notifier() in hns3_nic_init_irq(), because
we have registered notifier in irq_cpu_rmap_add() for each
vector, otherwise it may cause use-after-free issue.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Atheros/QCA AR7XXX/AR9XXX/QCA95XX built-in ethernet mac support
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MSI-X vector index is determined using qed device information and
affinity to use.
Signed-off-by: NChad Dupuis <cdupuis@marvell.com>
Signed-off-by: NSaurav Kashyap <skashyap@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MSI-X vector index is determined using qed device information and
affinity to use.
Signed-off-by: NManish Rangankar <mrangankar@marvell.com>
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 Always request for number of irqs equals to number of queues.

This reverts commit 1a291bce.
Signed-off-by: NManish Rangankar <mrangankar@marvell.com>
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add iWARP engine affinity setting for supporting iWARP over 100g.
iWARP cannot be distinguished by the LLH from L2, hence the
engine division will affect L2 as well. For this reason we add
a parameter to devlink to determine the engine division.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The table currently contains a single parameter for
configuring whether iWARP should be enabled on a 100g
device. Enabling iWARP on a 100g device impacts L2
performance and is therefore not enabled by default.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 100g mode the doorbell bar is united for both engines. Set
the correct offset in the hwfn so that the doorbell returned
for RoCE is in the affined hwfn.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NDenis Bolotin <denis.bolotin@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the msix vectors of the affined hwfn and not the
leading one.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To enable 100g support for offload protocols each PF gets
a dedicated engine to work on from the MFW.
This patch modifies the code to use the affined hwfn instead
of the leading one.
The offload protocols require the ll2 to be opened on both
engines, and not just the affined hwfn.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing status blocks use the affined hwfn
instead of the leading one for RDMA / Storage
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors the current llh implementation. It exposes a hw
resource called ppfid (port-pfid) and implements an API for configuring
the resource. Default configuration which was used until now limited
the number of filters per PF and did not support engine affinity per
protocol. The new API enables allocating more filter rules per PF and
enables affinitizing protocol packets to a certain engine which
enables full 100g protocol offload support.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies the dmae API to enable performing a dmae operation
to another PF. This enables sharing between the llh entries between PFs
and thus increasing the amount of filters per PF under certain
configurations.
The llh entries require using the dmae since the memory is widebus,
which requires atomicity in access.
Signed-off-by: NAriel Elior <ariel.elior@marvell.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When steering to an RXQ, we can perform an extra RSS step to assign a
queue from an RSS table.

This is done by setting the RSS_EN attribute in the C2 engine. In that
case, the RXQ that is assigned is the global RSS context id, that is
then translated to an RSS table using the RXQ2RSS table.

An example using ethtool to steer to RXQ 2 and 3 would be :

ethtool -X eth0 weight 0 0 1 1 context new

(This would print the allocated context id, let's say it's 1)

ethtool -N eth0 flow-type udp4 dst-port 1234 context 1 loc 0

The hash parameters are the ones that are globally configured for RSS :

ethtool -N eth0 rx-flow-hash udp4 sdfn

When an RSS context is removed while there are active classification
rules using this context, these rules are removed.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool_rx_flow_rule_create takes into parameter the ethtool flow spec,
which doesn't contain the rss context id. We therefore need to extract
it ourself before parsing the ethtool rule.

The FLOW_RSS flag is only set in info->fs.flow_type, and not
info->flow_type.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPv2 controller has 8 RSS tables that are shared across all ports on
a given PPv2 instance. The previous implementation allocated one table
per port, leaving others unused.

By using RSS contexts, we can make use of multiple RSS tables per
port, one being the default table (always id 0), the other ones being
used as destinations for flow steering, in the same way as rx rings.

This commit introduces RSS contexts management in the PPv2 driver. We
always reserve one table per port, allocated when the port is probed.

The global table list is stored in the struct mvpp2, as it's a global
resource. Each port then maintains a list of indices in that global
table, that way each port can have it's own numbering scheme starting
from 0.

One limitation that seems unavoidable is that the hashing parameters are
shared across all RSS contexts for a given port. Hashing parameters for
ctx 0 will be applied to all contexts.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The C2 TCAM has internal FIFOs that are only useful for the built-in
self-tests. Disable these FIFOS at init, as recommended in the
functionnal specs.
Suggested-by: NAlan Winkowski <walan@marvell.com>
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of today, the classification offload implementation only supports 4
different rules to be offloaded. This number has been hardcoded in the
rule insertion function, and the wrong define is being used elsewhere.

Use the correct #define everywhere to make sure we always check for the
correct number of rules.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we trigger NAPI we are disabling interrupts but in case we receive
or send a packet in the meantime, as interrupts are disabled, we will
miss this event.

Trigger both NAPI instances (RX and TX) when at least one event happens
so that we don't miss any interrupts.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.

Found out while running stmmac selftests.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.

This is also needed for stmmac Flow Control selftest.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.

This is also needed for stmmac Flow Control selftest.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for hash filter to work we need to set the HPF bit.

Fout out while running stmmac selftests
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.

Found out while running stmmac selftests.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for hash filter to work we need to set the HPF bit.

Found out while running stmmac selftests.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We add support for selftests on stmmac driver with 9 basic sanity checks
for now:
	- MAC Loopback
	- PHY Loopback
	- MMC Counters
	- EEE
	- Hash Filter Multicast
	- Perfect Filter Unicast
	- Multicast Filter All
	- Unicast Filter All
	- Flow Control

This allows for fast tracking of regressions in the driver and helps in
spotting mis-configuration of HW.

Changes from v1:
	- Fix build error as module (David)
	- Check for link status before running tests
Changes from RFC v2:
	- Return proper error code in stmmac_test_mmc (Corentin)
	- Use only 1 MMC counter in stmmac_test_mmc (Alexandre)
Changes from RFC v1:
	- Change test_loopback to test_mac_loopback (Andrew)
	- Change timeout to retries (Andrew)
	- Add MC/UC filter tests (Andrew)
	- Only test in offline mode (Andrew)
	- Do not call phy_loopback twice (Alexandre)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.

Pass this type of frames while in promiscuous mode.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.

Pass this type of frames while in promiscuous mode.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.

Pass this type of frames while in promiscuous mode.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XGMAC has a different MMC module. Lets use HWIF callbacks for MMC module
so that correct callbacks are automatically selected.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enable use of set_mac_loopback in dwmac-sun8i
Signed-off-by: NCorentin Labbe <clabbe@baylibre.com>
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwxgmac2 core.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac4/5 cores.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac1000 core.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac100 core.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the addition of selftests support for stmmac we add a
new callback to HWIF that can be used to set the controller in loopback
mode.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far we didn't support mode USXGMII, and in order to not break few
boards mode XGMII was accepted for the AQR107 family even though it
doesn't support XGMII. Add USXGMII support to the Aquantia PHY driver
and warn if XGMII mode is set.

v2:
- add warning if XGMII mode is set
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move fib6_nh to the end of fib6_info and make it an array of
size 0. Pass a flag to fib6_info_alloc indicating if the
allocation needs to add space for a fib6_nh.

The current code path always has a fib6_nh allocated with a
fib6_info; with nexthop objects they will be separate.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add get_ts_info interface for ethtool
to support getting timestamping capability.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add hardware timestamping support
for ENETC. On Rx, timestamping is enabled for all
frames. On Tx, we only instruct the hardware to
timestamp the frames marked accordingly by the stack.

Because the RX BD ring dynamic allocation has not been
supported and it is too expensive to use extended RX BDs
if timestamping is not used, a Kconfig option is used to
enable extended RX BDs in order to support hardware
timestamping. This option will be removed once RX BD
ring dynamic allocation is implemented.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>