Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8962 on Tobermory has one of the IN4 inputs connected for DC
measurement. Tell the driver it can optimise for this mode.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>

Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Saves a nice block of code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.

The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Provide managed versions of regulator_get() and regulator_bulk_get(),
saving code in error handling and cleanup paths by ensuring that that
the regulators will be automatically unregistered when the device is
unregistered.

As per discussion we can safely ignore the 8 and 16 bit sample
sizes when applying the msbits constraint.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Merge tag 'regmap-patch-initial' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into for-3.4

regmap: Inital export of the patching implementation

An initial export of the regmap register patch implementation, mostly
for integration into ASoC so it can be used by drivers there which have
conflicting updates already.

We only want them at the device level, not at the CODEC level.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Device manufacturers frequently provide register sequences, usually not
fully documented, to be run at startup in order to provide better defaults
for devices (for example, improving performance in the light of silicon
evaluation). Support such updates by allowing drivers to register update
sets with the core. These updates will be written to the device immediately
and will also be rewritten when the cache is synced.

The assumption is that the reason for resyncing the cache will always be
that the device has been powered off. If this turns out to not be the case
then a separate operation can be provided.

Currently the implementation only allows a single set of updates to be
specified for a device, this could be extended in future.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix below build warning when CONFIG_HOTPLUG is not set.

  CC      sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
  CC      sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert to table based DAPM and control init.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow drivers to benefit from both the bulk APIs and managed resources
simultaneously.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow consumers to free regulators allocated using devm_regulator_get()
if they need to. This will not normally be required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In preparation for conversion to regmap.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Visstrim_M10 has an external class D amplifier.
This patch provides support for controlling the 4
possible gain levels and per channel muting.
Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

On the off chance that an application both pays attention and gets
confused.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>