[Why]
Currently all timedout job will be considered to be guilty. In SRIOV
multi-vf use case, the vf flr happens first and then job time out is
found. There can be several jobs timeout during a very small time slice.
And if the innocent sdma job time out is found before the real bad
job, then the innocent sdma job will be set to guilty. This will lead
to a page fault after resubmitting job.

[How]
If the job is a kernel job, we will always consider it not guilty
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NJingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update Arcturus/Aldebaran thermal throttle SMI event path to use
ASIC-independent throttler bits when logging.
Signed-off-by: NGraham Sider <Graham.Sider@amd.com>
Reviewed-by: NHarish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix make htmldocs complaint:
./drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:628: warning: Excess function parameter 'interrupt_params' description in 'DMUB_TRACE_MAX_READ'

v2:
Moved DMUB_TRACE_MAX_READ macro above function documentation
Signed-off-by: NAnson Jacob <Anson.Jacob@amd.com>
CC: Harry Wentland <harry.wentland@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add new line to phy_settings output
Signed-off-by: NAnson Jacob <Anson.Jacob@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

link_rate is updated via debugfs using hex values, set it to output
in hex as well.

eg: Resolution: 1920x1080@144Hz
cat /sys/kernel/debug/dri/0/DP-1/link_settings
Current:  4  0x14  0  Verified:  4  0x1e  0  Reported:  4  0x1e  16  Preferred:  0  0x0  0

echo "4 0x1e" > /sys/kernel/debug/dri/0/DP-1/link_settings

cat /sys/kernel/debug/dri/0/DP-1/link_settings
Current:  4  0x1e  0  Verified:  4  0x1e  0  Reported:  4  0x1e  16  Preferred:  4  0x1e  0
Signed-off-by: NAnson Jacob <Anson.Jacob@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

start_cpsch and stop_cpsch can be called during kfd device
initialization or during gpu reset/recovery. So they can
run concurrently. Currently in start_cpsch and stop_cpsch,
pm_init and pm_uninit is not protected by the dpm lock.
Imagine such a case that user use packet manager's function
to submit a pm4 packet to hang hws (ie through command
cat /sys/class/kfd/kfd/topology/nodes/1/gpu_id | sudo tee
/sys/kernel/debug/kfd/hang_hws), while kfd device is under
device reset/recovery so packet manager can be not initialized.
There will be unpredictable protection fault in such case.

This patch moves pm_init/uninit inside the dpm lock and check
packet manager is initialized before using packet manager
function.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NChristian Konig <christian.koenig@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This variable will be used to determine whether packet
manager is initialized or not, in a future patch.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NChristian Konig <christian.koenig@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Renaming packets to packet_mgr to reflect the real meaning
of this variable.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NChristian Konig <christian.koenig@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Function name "psp_np_fw_load" is not proper as people don't
know _np_fw_ means "non psp firmware". Change the function
name to psp_load_non_psp_fw for better understanding. Same
thing for function psp_execute_np_fw_load.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian Konig <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The printing message "PSP loading VCN firmware" is mis-leading because
people might think driver is loading VCN firmware. Actually when this
message is printed, driver is just preparing some VCN ucode, not loading
VCN firmware yet. The actual VCN firmware loading will be in the PSP block
hw_init. Fix the printing message
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NChristian Konig <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Squash in warning fix (Alex)
Signed-off-by: NRoy Sun <Roy.Sun@amd.com>
Reviewed-by: NZhou pengju <pengju.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The callback functions are used for SRIOV read/write instead
of just for rlcg read/write
Signed-off-by: NRoy Sun <Roy.Sun@amd.com>
Reviewed-by: NZhou pengju <pengju.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NVeerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com>
Reviewed-by: NJames Zhu <James.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Similar to xGMI reporting the min/max bandwidth between direct peers, PCIe
will report the min/max bandwidth to the KFD.
Signed-off-by: NJonathan Kim <jonathan.kim@amd.com>
Reviewed-by: NFelix Kuehling <felix.kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Report the min/max bandwidth in megabytes to the kfd for direct
xgmi connections only.  Indirect peers will report 0 since
indirect route is unknown.
Signed-off-by: NJonathan Kim <jonathan.kim@amd.com>
Reviewed-by: NFelix Kuehling <felix.kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The TA can now be invoked to provide the number of xgmi links connecting
a direct source and destination peer.
Non-direct peers will report zero links.
Signed-off-by: NJonathan Kim <jonathan.kim@amd.com>
Reviewed-by: NFelix Kuehling <felix.kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

make htmldocs complaints about parameter for amdgpu_bo_add_to_shadow_list

./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list'
./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Function parameter or member 'vmbo' not described in 'amdgpu_bo_add_to_shadow_list'
./drivers/gpu/drm/amd/amdgpu/amdgpu_object.c:739: warning: Excess function parameter 'bo' description in 'amdgpu_bo_add_to_shadow_list'
Signed-off-by: NAnson Jacob <Anson.Jacob@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NKevin Wang <kevin1.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.

[How]
Change zstate support condition to match updated policy
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

DC version 3.2.145 brings improvements in multiple areas. In summary, we
highlight:

- Code improvements for passive
- Cursor manipulation enhancements
- Expand debug in some areas
- Fix problems in DML
- Other minor code refactors
Reviewed-by: NAnson Jacob <Anson.Jacob@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

- Add reserved bits for future feature development
- Fix issue with mismatch with type const
- Replaced problematic code with old memcpy and casted problematic
  pointers to unsigned char pointers
Reviewed-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
There's a special case where upper plane is not the main plane. If it owns
the cursor, it will be invisible in the majority of the screen.

[How]
The condition for disabling cursor is changed:
- check if upper viewport completely covers current. This was the
previous change that doesn't handle all scenarios with pipe splitting.
- if not, show the cursor only if it's not scaled or no upper pipe.
Reviewed-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.

[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When an riommu invalidation request come at the same time as a pipe is
disabled there can be a case where DCN cannot ACK the request if only
one VMID is setup in the inuse list.

[How]
Setup a second unused VMID will work around the issue.
Reviewed-by: NJun Lei <jun.lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: NJun Lei <jun.lei@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NNevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.

[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
When finding a second pipe for pipe split, currently will look for
bottom pipe in context first to decide the second pipe. This causes
issues in 2 plane to 1 plane transitions like fullscreen video where
bottom pipe no longer exists in the new configuration.

[HOW]
If previous context had an ODM pipe, use that to find the secondary pipe
first before looking at bottom pipe.
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nsunglee <sunglee@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.

[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: NKrunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NCamille Cho <Camille.Cho@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.

Put in a hardcoded default until we have the interface in place.
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.

In the case where the hardcode is also missing we can't lightup display.

[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.

[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.

Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.

An example of such a timing would be 640x480@72Hz:

h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000

[How]
Include borders as part of destination vactive/hactive.

This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.

Most modes do not have vertical or horizontal borders.
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Enable feature for 21.40
Reviewed-by: NSung Lee <Sung.Lee@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Reviewed-by: NShahin Khayyer <Shahin.Khayyer@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.

[how]
Correct "<" to "<="
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NYongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NVictor Lu <victorchengchi.lu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
During headless boot, DIG may be on which causes HW/SW discrepancies.
To avoid this we power down hardware on boot if DIG is turned on. With
introduction of multiple eDP, hardware power down is being bypassed
under certain conditions.

[How]
Fixed hardware power down bypass, and ensured hardware will power down
if DIG is on and seamless boot is not enabled.
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NJake Wang <haonan.wang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Reviewed-by: NShahin Khayyer <Shahin.Khayyer@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Theoretically, per DP 1.4a spec, sink device needs to AUX_ACK 00340h
write. However, due to hardware limitation, some sink devices have no
00340h dpcd address at all. This results in sink side fails to reply
ACK, and consequently cause source side keep retrying DPCD write on DPCD
00340h. This results in significant delay when DPCD 00340h write is
triggered (e.g. at S3 resume).

[How]
Check whether sink device could ACK on DPCD 00340h write on boot. If
sink device fails to ACK, then remember that, so we won't write to DPCD
00340h later on.

There will be a drm.debug KMS level message to inform user once a 00340h
DPCD write is skipped on purpose.
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NZhan Liu <zhan.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
Print a debug message when dcc validation fails in the display driver.
Most DCC enablement related errors are from userspace. Adding a debug
print in case of a failure from display driver will aid quicker triage.
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>