The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.

This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset

The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module.  In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.

When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Acked-by: NMaciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Since 43cc71ee, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.

Cc: <stable@kernel.org>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Haavard's dma-slave interface would like to test for exclusive access to a
channel.  The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.

This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The dependency is redundant since all drivers set their specific arch
dependencies.  The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect.  HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.
Acked-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.

This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

commit 636bdeaa 'dmaengine: ack to flags: make use of the unused bits in
the 'ack' field' missed an ->ack conversion in
crypto/async_tx/async_memset.c
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NZhang Wei <zw@zh-kernel.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

> +#define	ARCH_KMALLOC_MINALIGN		(sizeof(long) * 2)
> +#define	ARCH_SLAB_MINALIGN		(sizeof(long) * 2)

This doesn't work if SLAB is selected and slab debugging is enabled as
these are passed to the preprocessor, and the preprocessor doesn't
understand sizeof.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cfq-iosched: fix RCU problem in cfq_cic_lookup()
  block: make blktrace use per-cpu buffers for message notes
  Added in elevator switch message to blktrace stream
  Added in MESSAGE notes for blktraces
  block: reorder cfq_queue to save space on 64bit builds
  block: Move the second call to get_request to the end of the loop
  splice: handle try_to_release_page() failure
  splice: fix sendfile() issue with relay

Specify the minimum slab/kmalloc alignment to be 8 bytes.  This fixes a
crash when SLOB is selected as the memory allocator.  The FRV arch needs
this so that it can use the load- and store-double instructions without
faulting.  By default SLOB sets the minimum to be 4 bytes.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a typo in the header guard of asm/ipc.h.
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cfq_cic_lookup() needs to properly protect ioc->ioc_data before
dereferencing it and also exclude updaters of ioc->ioc_data as well.

Also add a number of comments documenting why the existing RCU usage
is OK.

Thanks a lot to "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> for
review and comments!
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Currently it uses a single static char array, but that risks
being corrupted when multiple users issue message notes at the
same time. Make the buffers dynamically allocated when the trace
is setup and make them per-cpu instead.

The default max message size of 1k is also very large, the
interface is mainly for small text notes. So shrink it to 128 bytes.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NAlan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Allows messages to be inserted into blktrace streams.
Signed-off-by: NAlan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

saves 8 bytes of padding & increases objects/slab from 30 to 32 on my
AMD64 config
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

In function get_request_wait, the second call to get_request could be
moved to the end of the while loop, because if the first call to
get_request fails, the second call will fail without sleep.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

splice currently assumes that try_to_release_page() always suceeds,
but it can return failure. If it does, we cannot steal the page.

Acked-by: Mingming Cao <cmm@us.ibm.com
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Splice isn't always incrementing the ppos correctly, which broke
relay splice.
Signed-off-by: NTom Zanussi <zanussi@comcast.net>
Tested-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  pciehp: add message about pciehp_slot_with_bus option
  pci hotplug core: add check of duplicate slot name
  pciehp: move msleep after power off
  pciehp: poll cmd completion if hotplug interrupt is disabled
  pciehp: fix slow probing
  pciehp: fix NULL dereference in interrupt handler
  shpchp: add message about shpchp_slot_with_bus option
  PCI: don't enable ASPM on devices with mixed PCIe/PCI functions

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3 #1
 [<c0266980>] kobject_add_internal+0x140/0x190
 [<c0266afd>] kobject_init_and_add+0x2d/0x40
 [<c027bc91>] pci_hp_register+0x81/0x2f0
 [<c027fd07>] pciehp_probe+0x1a7/0x470
 [<c01b3b84>] sysfs_add_one+0x44/0xa0
 [<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
 [<c01b497a>] sysfs_create_link+0x8a/0xf0
 [<c0279570>] pcie_port_probe_service+0x50/0x80
 [<c02e0545>] driver_sysfs_add+0x55/0x70
 [<c02e0662>] driver_probe_device+0x82/0x180
 [<c02e07cc>] __driver_attach+0x6c/0x70
 [<c02dfe0a>] bus_for_each_dev+0x3a/0x60
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e04e6>] driver_attach+0x16/0x20
 [<c02e0760>] __driver_attach+0x0/0x70
 [<c02e0341>] bus_add_driver+0x1a1/0x220
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c02e09cd>] driver_register+0x4d/0x120
 [<c05db050>] ibm_acpiphp_init+0x0/0x190
 [<c0125aab>] printk+0x1b/0x20
 [<c05db2d0>] pcied_init+0x0/0x80
 [<c05db2de>] pcied_init+0xe/0x80
 [<c05c751a>] kernel_init+0x10a/0x300
 [<c0120138>] schedule_tail+0x18/0x50
 [<c0103b9a>] ret_from_fork+0x6/0x1c
 [<c05c7410>] kernel_init+0x0/0x300
 [<c05c7410>] kernel_init+0x0/0x300
 [<c010485b>] kernel_thread_helper+0x7/0x1c
 =======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22

Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix improper long wait for command completion in pciehp probing.

As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.

This patch changes the pciehp driver to take such command into
account.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.

The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).

The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.

This problem seems to be revealed by the commit
c27fb883 that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fix the following NULL dereference problem reported from Pierre Ossman
and Ingo Molnar.

pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
pciehp: pciehp_find_slot: slot (device=0x0) not found
BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
IP: [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
PGD 0
Oops: 0000 [1]
CPU 0
Modules linked in:
Pid: 1, comm: swapper Tainted: G        W 2.6.26-rc3-sched-devel.git-00001-g2b99b26-dirty #170
RIP: 0010:[<ffffffff80494a8b>]  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
RSP: 0000:ffff81003f83fbb0  EFLAGS: 00010046
RAX: 0000000000000039 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000046
RBP: ffff81003f83fbd0 R08: 0000000000000001 R09: ffffffff80245103
R10: 0000000000000020 R11: 0000000000000000 R12: ffff81003ea53a30
R13: 0000000000000000 R14: 0000000000000011 R15: ffffffff80495926
FS:  0000000000000000(0000) GS:ffffffff80be7400(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000070 CR3: 0000000000201000 CR4: 00000000000006a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 1, threadinfo ffff81003f83e000, task ffff81003f840000)
Stack:  0000000000000008 ffff81003f83fbf6 ffff81003ea53a30 0000000000000008
 ffff81003f83fc10 ffffffff80495ab4 0000000000000011 0000000000000002
 0000000000000202 0000000000000202 00000000fffffff4 ffff81003ea53a30
Call Trace:
 [<ffffffff80495ab4>] pcie_isr+0x18e/0x1bc
 [<ffffffff80260831>] request_irq+0x106/0x12f
 [<ffffffff80495fb6>] pcie_init+0x15e/0x6cc
 [<ffffffff804933a3>] pciehp_probe+0x64/0x541
 [<ffffffff8048f4e7>] pcie_port_probe_service+0x4c/0x76
 [<ffffffff8054af70>] driver_probe_device+0xd4/0x1f0
 [<ffffffff8054b108>] __driver_attach+0x7c/0x7e
 [<ffffffff8054b08c>] ? __driver_attach+0x0/0x7e
 [<ffffffff8054a4b6>] bus_for_each_dev+0x53/0x7d
 [<ffffffff8054ad3c>] driver_attach+0x1c/0x1e
 [<ffffffff8054a9c2>] bus_add_driver+0xdd/0x25b
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8054b288>] driver_register+0x5f/0x13e
 [<ffffffff80c09d3d>] ? pcied_init+0x0/0x8b
 [<ffffffff8048f441>] pcie_port_service_register+0x47/0x49
 [<ffffffff80c09d52>] pcied_init+0x15/0x8b
 [<ffffffff80bf3938>] kernel_init+0x75/0x243
 [<ffffffff808639d2>] ? _spin_unlock_irq+0x2b/0x3a
 [<ffffffff80228d1f>] ? finish_task_switch+0x57/0x9a
 [<ffffffff8020c258>] child_rip+0xa/0x12
 [<ffffffff8020bcec>] ? restore_args+0x0/0x30
 [<ffffffff80bf38c3>] ? kernel_init+0x0/0x243
 [<ffffffff8020c24e>] ? child_rip+0x0/0x12

Code: 83 80 00 00 00 48 39 f0 75 e1 0f b6 c9 48 c7 c2 00 0e 8d 80 48 c7 c6 8a 60 a6 80 48 c7 c7 10 db a8 80 31 c0 e8 3f 8d d9 ff 31 db <48> 8b 43 70 48 8d 75 ef 48 89 df ff 50 30 80 7d ef 00 74 37 48
RIP  [<ffffffff80494a8b>] pciehp_handle_presence_change+0x7e/0x113
 RSP <ffff81003f83fbb0>
CR2: 0000000000000070
Kernel panic - not syncing: Fatal exception

The situation under which it occurs is hw and timing related: it appears
to happen on a system that has PCI hotplug hardware but with no active
hotplug cards, and another interrupt in the same (shared) IRQ line
arrives too early, before the hotplug-slot entry has been set up - as
triggered by CONFIG_DEBUG_SHIRQ=y:

This patch contains the following two fixes.

(1) Clear all events bits in Slot Status register to prevent the pciehp
    driver from detecting the spurious events that would have been occur
    before pciehp loading.

(2) Add check whether slot initialization had been already done.

This is short term fix. We need more structural fixes to install
interrupt handler after slot initialization is done.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: Fix cpufreq oops when ondemand governor is default
  avr32: Update defconfigs
  avr32: export strnlen_user
  avr32: export copy_page

There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: NCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.

As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.

Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.

This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Align i2c_device_id
  tuner: Do not alter i2c_client.name

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: ksize() abuse checks
  slob: Fix to return wrong pointer

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
  sh: Drop broken URAM support on SH7723.
  sh: update Migo-R defconfig
  sh: use sm501 8250 mfd support on r2d boards
  sh: add probe support for new sh7723 cut
  sh: fix VPU interrupt vector for sh7723
  sh: fix USBF resource for sh7722

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: global_reg_snapshot is not for userspace

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
  vlan: Use bitmask of feature flags instead of seperate feature bits
  fmvj18x_cs: add NextCom NC5310 rev B support
  xirc2ps_cs: re-initialize the multicast address in do_reset
  3C509: rx_bytes should not be increased when alloc_skb failed
  NETFRONT: Use __skb_queue_purge()
  VIRTIO: Use __skb_queue_purge()
  phylib: do EXPORT_SYMBOL on get_phy_id
  netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
  WAN: protect HDLC proto list while insmod/rmmod
  drivers/net/fs_enet: remove null pointer dereference
  S2io: Version update for napi and MSI-X patches
  S2io: Added napi support when MSIX is enabled.
  S2io: Move all the transmit completions to a single msi-x (alarm) vector
  drivers/net/ehea - remove unnecessary memset after kzalloc
  au1000_eth: remove useless check
  Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
  cpmac bugfixes and enhancements
  e1000e: use resource_size_t, not unsigned long, for phys addrs
  net/usb: add support for Apple USB Ethernet Adapter
  uli526x: add support for netpoll
  ...

Align i2c_device_id.driver_data to 8 bytes to not fail on crossbuilds.

(Added in d2653e92.)
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>