Variable ret is initialized to a value that is never read before
a return statement and hence can be removed. Remove it.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813133114.14931-1-colin.king@canonical.comSigned-off-by: NMark Brown <broonie@kernel.org>

During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.

The WR_S bit allows the TWL6030 to no reset at all the VMMC during warm
reset and keep the current voltage. Thanks to this workaround the SD
card doesn't reach a undefined reset stage.

Actually this behavior is available for all the LDO regulator, so the
driver will also allow to use it with any of these regulator.
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-4-gregory.clement@bootlin.comSigned-off-by: NMark Brown <broonie@kernel.org>

Instead of refering the full pdev->dev.of_node use a local variable.
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-3-gregory.clement@bootlin.comSigned-off-by: NMark Brown <broonie@kernel.org>

Add the PMIC5 modes and use them pmic5 ldo and smps
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-4-vkoul@kernel.orgSigned-off-by: NMark Brown <broonie@kernel.org>

pmic5_bob voltages count is 136 [0,135] so update it
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-3-vkoul@kernel.orgSigned-off-by: NMark Brown <broonie@kernel.org>

It helps to keep sorted order for compatibles, so sort them
Suggested-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-2-vkoul@kernel.orgSigned-off-by: NMark Brown <broonie@kernel.org>

Building without CONFIG_POWER_SUPPLY will fail:

drivers/regulator/act8865-regulator.o: In function `act8865_pmic_probe':
act8865-regulator.c:(.text+0x357): undefined reference to `devm_power_supply_register'
drivers/regulator/act8865-regulator.o: In function `act8600_charger_get_property':
act8865-regulator.c:(.text+0x3f1): undefined reference to `power_supply_get_drvdata'

Add POWER_SUPPLY dependency to Kconfig.
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 2d09a79b ("regulator: act8865: Add support for act8600 charger")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190807133822.67124-1-yuehaibing@huawei.comSigned-off-by: NMark Brown <broonie@kernel.org>

Add support from RPMH regulators found in SM8150 platform
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190808093343.5600-2-vkoul@kernel.orgSigned-off-by: NMark Brown <broonie@kernel.org>

Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: NNishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804162023.5673-1-nishkadg.linux@gmail.comSigned-off-by: NMark Brown <broonie@kernel.org>

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NStephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-38-swboyd@chromium.orgSigned-off-by: NMark Brown <broonie@kernel.org>

drivers/regulator/act8865-regulator.c:447:8-14: WARNING: PTR_ERR_OR_ZERO can be used

 Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci

Fixes: 2d09a79b ("regulator: act8865: Add support for act8600 charger")
CC: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Nkbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190724092236.witxtfmubun25l2t@1905cc33b6ddSigned-off-by: NMark Brown <broonie@kernel.org>

AC8865 has internal 1.5k pull-down resistor that can be enabled when LDO
is shut down.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/d7338f0dfcac63eb958a6b5e42e2d540b3d3f54a.1563898936.git.mirq-linux@rere.qmqm.plSigned-off-by: NMark Brown <broonie@kernel.org>

Rename act8865_ldo_ops to act8865_fixed_ldo_ops to make room for
variable-output LDO ops change.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/12b1fe419e93dfe663990009bf1b2fbf630e9934.1563898936.git.mirq-linux@rere.qmqm.plSigned-off-by: NMark Brown <broonie@kernel.org>

Setting .n_voltages = 1 and .fixed_uV is enough for fixed regulator,
remove the redundant .min_uV and .list_voltage settings.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20190723014102.25103-1-axel.lin@ingics.comSigned-off-by: NMark Brown <broonie@kernel.org>

This provides a way to monitor battery charge status via the power
supply subsystem.
Signed-off-by: NMaarten ter Huurne <maarten@treewalker.org>
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190723011418.29143-1-paul@crapouillou.netSigned-off-by: NMark Brown <broonie@kernel.org>

-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190711122138.5221-1-axel.lin@ingics.comSigned-off-by: NMark Brown <broonie@kernel.org>

According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage (50-mV steps): VPOS = 4 V + (Code × 50 mV), 6.5 V max
000000 = 4 V
000001 = 4.05 V
:
011110 = 5.5 V (Default)
:
110010 = 6.5 V
110011 to 111111 map to 6.5 V

So the LM36274_LDO_VSEL_MAX should be 0b110010 (0x32).
The valid selectors are 0 ... LM36274_LDO_VSEL_MAX, n_voltages should be
LM36274_LDO_VSEL_MAX + 1. Similarly, the n_voltages should be
LM36274_BOOST_VSEL_MAX + 1 for LM36274_BOOST.

Fixes: bff5e807 ("regulator: lm363x: Add support for LM36274")
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-2-axel.lin@ingics.comSigned-off-by: NMark Brown <broonie@kernel.org>

According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V

The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.

Fixes: 3a8d1a73 ("regulator: add LM363X driver")
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.comSigned-off-by: NMark Brown <broonie@kernel.org>

The commit b3aa14f0 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.

   kernel BUG at drivers/iommu/iova.c:801!
    Workqueue: kblockd blk_mq_run_work_fn
    RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
    Call Trace:
     free_cpu_cached_iovas+0xbd/0x150
     alloc_iova_fast+0x8c/0xba
     dma_ops_alloc_iova.isra.6+0x65/0xa0
     map_sg+0x8c/0x2a0
     scsi_dma_map+0xc6/0x160
     pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
     pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
     scsi_queue_rq+0x79c/0x1200
     blk_mq_dispatch_rq_list+0x4dc/0xb70
     blk_mq_sched_dispatch_requests+0x249/0x310
     __blk_mq_run_hw_queue+0x128/0x200
     blk_mq_run_work_fn+0x27/0x30
     process_one_work+0x522/0xa10
     worker_thread+0x63/0x5b0
     kthread+0x1d2/0x1f0
     ret_from_fork+0x22/0x40

Fixes: b3aa14f0 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: NQian Cai <cai@lca.pw>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the function alps_is_cs19_trackpoint(), we check if the param[1] is
in the 0x20~0x2f range, but the code we wrote for this checking is not
correct:
(param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f,
it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f...

Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20).

Fixes: 7e4935cc ("Input: alps - don't handle ALPS cs19 trackpoint-only device")
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

trackpoint_detect() should be static inline while
CONFIG_MOUSE_PS2_TRACKPOINT is not set, otherwise, we build fails:

drivers/input/mouse/alps.o: In function `trackpoint_detect':
alps.c:(.text+0x8e00): multiple definition of `trackpoint_detect'
drivers/input/mouse/psmouse-base.o:psmouse-base.c:(.text+0x1b50): first defined here
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 55e3d922 ("Input: psmouse - allow disabing certain protocol extensions")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/input/keyboard/applespi.c: In function applespi_set_bl_level:
drivers/input/keyboard/applespi.c:902:6: warning: variable sts set but not used [-Wunused-but-set-variable]

Fixes: b426ac0452093d ("Input: add Apple SPI keyboard and trackpad driver")
Signed-off-by: NMao Wenan <maowenan@huawei.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The keyboard and trackpad on recent MacBook's (since 8,1) and
MacBookPro's (13,* and 14,*) are attached to an SPI controller instead
of USB, as previously. The higher level protocol is not publicly
documented and hence has been reverse engineered. As a consequence there
are still a number of unknown fields and commands. However, the known
parts have been working well and received extensive testing and use.

In order for this driver to work, the proper SPI drivers need to be
loaded too; for MB8,1 these are spi_pxa2xx_platform and spi_pxa2xx_pci;
for all others they are spi_pxa2xx_platform and intel_lpss_pci.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=99891
Link: https://bugzilla.kernel.org/show_bug.cgi?id=108331Signed-off-by: NRonald Tschalär <ronald@innovation.ch>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Appears to be fixed by "flcn/gp102-: improve implementation of
bind_context() on SEC2/GSP".

Tested on GP10[24678] and GV100.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes various issues encountered while attempting to initialise ACR.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

In nouveau_conn_reset(), if connector->state is true,
__drm_atomic_helper_connector_destroy_state() will be called,
but the memory pointed by asyc isn't freed. Memory leak happens
in the following function __drm_atomic_helper_connector_reset(),
where newly allocated asyc->state will be assigned to connector->state.

So using nouveau_conn_atomic_destroy_state() instead of
__drm_atomic_helper_connector_destroy_state to free the "old" asyc.

Here the is the log showing memory leak.

unreferenced object 0xffff8c5480483c80 (size 192):
  comm "kworker/0:2", pid 188, jiffies 4294695279 (age 53.179s)
  hex dump (first 32 bytes):
    00 f0 ba 7b 54 8c ff ff 00 00 00 00 00 00 00 00  ...{T...........
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000005005c0d0>] kmem_cache_alloc_trace+0x195/0x2c0
    [<00000000a122baed>] nouveau_conn_reset+0x25/0xc0 [nouveau]
    [<000000004fd189a2>] nouveau_connector_create+0x3a7/0x610 [nouveau]
    [<00000000c73343a8>] nv50_display_create+0x343/0x980 [nouveau]
    [<000000002e2b03c3>] nouveau_display_create+0x51f/0x660 [nouveau]
    [<00000000c924699b>] nouveau_drm_device_init+0x182/0x7f0 [nouveau]
    [<00000000cc029436>] nouveau_drm_probe+0x20c/0x2c0 [nouveau]
    [<000000007e961c3e>] local_pci_probe+0x47/0xa0
    [<00000000da14d569>] work_for_cpu_fn+0x1a/0x30
    [<0000000028da4805>] process_one_work+0x27c/0x660
    [<000000001d415b04>] worker_thread+0x22b/0x3f0
    [<0000000003b69f1f>] kthread+0x12f/0x150
    [<00000000c94c29b7>] ret_from_fork+0x3a/0x50
Signed-off-by: NYongxin Liu <yongxin.liu@windriver.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

In nouveau_dmem_pages_alloc(), the drm->dmem->mutex is unlocked before
calling nouveau_dmem_chunk_alloc() as shown when CONFIG_PROVE_LOCKING
is enabled:

[ 1294.871933] =====================================
[ 1294.876656] WARNING: bad unlock balance detected!
[ 1294.881375] 5.2.0-rc3+ #5 Not tainted
[ 1294.885048] -------------------------------------
[ 1294.889773] test-malloc-vra/6299 is trying to release lock (&drm->dmem->mutex) at:
[ 1294.897482] [<ffffffffa01a220f>] nouveau_dmem_migrate_alloc_and_copy+0x79f/0xbf0 [nouveau]
[ 1294.905782] but there are no more locks to release!
[ 1294.910690]
[ 1294.910690] other info that might help us debug this:
[ 1294.917249] 1 lock held by test-malloc-vra/6299:
[ 1294.921881]  #0: 0000000016e10454 (&mm->mmap_sem#2){++++}, at: nouveau_svmm_bind+0x142/0x210 [nouveau]
[ 1294.931313]
[ 1294.931313] stack backtrace:
[ 1294.935702] CPU: 4 PID: 6299 Comm: test-malloc-vra Not tainted 5.2.0-rc3+ #5
[ 1294.942786] Hardware name: ASUS X299-A/PRIME X299-A, BIOS 1401 05/21/2018
[ 1294.949590] Call Trace:
[ 1294.952059]  dump_stack+0x7c/0xc0
[ 1294.955469]  ? nouveau_dmem_migrate_alloc_and_copy+0x79f/0xbf0 [nouveau]
[ 1294.962213]  print_unlock_imbalance_bug.cold.52+0xca/0xcf
[ 1294.967641]  lock_release+0x306/0x380
[ 1294.971383]  ? nouveau_dmem_migrate_alloc_and_copy+0x79f/0xbf0 [nouveau]
[ 1294.978089]  ? lock_downgrade+0x2d0/0x2d0
[ 1294.982121]  ? find_held_lock+0xac/0xd0
[ 1294.985979]  __mutex_unlock_slowpath+0x8f/0x3f0
[ 1294.990540]  ? wait_for_completion+0x230/0x230
[ 1294.995002]  ? rwlock_bug.part.2+0x60/0x60
[ 1294.999197]  nouveau_dmem_migrate_alloc_and_copy+0x79f/0xbf0 [nouveau]
[ 1295.005751]  ? page_mapping+0x98/0x110
[ 1295.009511]  migrate_vma+0xa74/0x1090
[ 1295.013186]  ? move_to_new_page+0x480/0x480
[ 1295.017400]  ? __kmalloc+0x153/0x300
[ 1295.021052]  ? nouveau_dmem_migrate_vma+0xd8/0x1e0 [nouveau]
[ 1295.026796]  nouveau_dmem_migrate_vma+0x157/0x1e0 [nouveau]
[ 1295.032466]  ? nouveau_dmem_init+0x490/0x490 [nouveau]
[ 1295.037612]  ? vmacache_find+0xc2/0x110
[ 1295.041537]  nouveau_svmm_bind+0x1b4/0x210 [nouveau]
[ 1295.046583]  ? nouveau_svm_fault+0x13e0/0x13e0 [nouveau]
[ 1295.051912]  drm_ioctl_kernel+0x14d/0x1a0
[ 1295.055930]  ? drm_setversion+0x330/0x330
[ 1295.059971]  drm_ioctl+0x308/0x530
[ 1295.063384]  ? drm_version+0x150/0x150
[ 1295.067153]  ? find_held_lock+0xac/0xd0
[ 1295.070996]  ? __pm_runtime_resume+0x3f/0xa0
[ 1295.075285]  ? mark_held_locks+0x29/0xa0
[ 1295.079230]  ? _raw_spin_unlock_irqrestore+0x3c/0x50
[ 1295.084232]  ? lockdep_hardirqs_on+0x17d/0x250
[ 1295.088768]  nouveau_drm_ioctl+0x9a/0x100 [nouveau]
[ 1295.093661]  do_vfs_ioctl+0x137/0x9a0
[ 1295.097341]  ? ioctl_preallocate+0x140/0x140
[ 1295.101623]  ? match_held_lock+0x1b/0x230
[ 1295.105646]  ? match_held_lock+0x1b/0x230
[ 1295.109660]  ? find_held_lock+0xac/0xd0
[ 1295.113512]  ? __do_page_fault+0x324/0x630
[ 1295.117617]  ? lock_downgrade+0x2d0/0x2d0
[ 1295.121648]  ? mark_held_locks+0x79/0xa0
[ 1295.125583]  ? handle_mm_fault+0x352/0x430
[ 1295.129687]  ksys_ioctl+0x60/0x90
[ 1295.133020]  ? mark_held_locks+0x29/0xa0
[ 1295.136964]  __x64_sys_ioctl+0x3d/0x50
[ 1295.140726]  do_syscall_64+0x68/0x250
[ 1295.144400]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1295.149465] RIP: 0033:0x7f1a3495809b
[ 1295.153053] Code: 0f 1e fa 48 8b 05 ed bd 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d bd bd 0c 00 f7 d8 64 89 01 48
[ 1295.171850] RSP: 002b:00007ffef7ed1358 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 1295.179451] RAX: ffffffffffffffda RBX: 00007ffef7ed1628 RCX: 00007f1a3495809b
[ 1295.186601] RDX: 00007ffef7ed13b0 RSI: 0000000040406449 RDI: 0000000000000004
[ 1295.193759] RBP: 00007ffef7ed13b0 R08: 0000000000000000 R09: 000000000157e770
[ 1295.200917] R10: 000000000151c010 R11: 0000000000000246 R12: 0000000040406449
[ 1295.208083] R13: 0000000000000004 R14: 0000000000000000 R15: 0000000000000000

Reacquire the lock before continuing to the next page.
Signed-off-by: NRalph Campbell <rcampbell@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

fixes bogus values userspace gets from hwmon while the GPU is powered down
Signed-off-by: NKarol Herbst <kherbst@redhat.com>
Reviewed-by: NRhys Kidd <rhyskidd@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The bulk SPDX addition made all these files into GPL-2.0 licensed files.
However the remainder of the project is MIT-licensed, these files
were simply missing the boiler plate and got caught up in the global update.

Fixes: 96ac6d43 (treewide: Add SPDX license identifier - Kbuild)
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The bulk SPDX addition made all these files into GPL-2.0 licensed files.
However the remainder of the project is MIT-licensed, these files
(primarily header files) were simply missing the boiler plate and got
caught up in the global update.

Fixes: b2441318 (License cleanup: add SPDX GPL-2.0 license identifier to files with no license)
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Acked-by: NEmil Velikov <emil.l.velikov@gmail.com>
Acked-by: NKarol Herbst <kherbst@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It turns out that while disabling i2c bus access from software when the
GPU is suspended was a step in the right direction with:

commit 342406e4 ("drm/nouveau/i2c: Disable i2c bus access after
->fini()")

We also ended up accidentally breaking the vbios init scripts on some
older Tesla GPUs, as apparently said scripts can actually use the i2c
bus. Since these scripts are executed before initializing any
subdevices, we end up failing to acquire access to the i2c bus which has
left a number of cards with their fan controllers uninitialized. Luckily
this doesn't break hardware - it just means the fan gets stuck at 100%.

This also means that we've always been using our i2c busses before
initializing them during the init scripts for older GPUs, we just didn't
notice it until we started preventing them from being used until init.
It's pretty impressive this never caused us any issues before!

So, fix this by initializing our i2c pad and busses during subdev
pre-init. We skip initializing aux busses during pre-init, as those are
guaranteed to only ever be used by nouveau for DP aux transactions.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Tested-by: NMarc Meledandri <m.meledandri@gmail.com>
Fixes: 342406e4 ("drm/nouveau/i2c: Disable i2c bus access after ->fini()")
Cc: stable@vger.kernel.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Regs seem valid here still, and tested on TU116.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Modesetting only, still waiting on ACR/GR firmware from NVIDIA for Turing
graphics/compute bring-up.

Each subsystem was compared with traces, along with various tests to check
that things generally work as they should, and appears compatible enough
with the current TU117 code to enable support.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The fallthrough cases (pre-Fermi) would accidentally allow dual-link pixel
clocks even where they shouldn't be.  This leads to a high resolution HDMI
displays, connected via a DVI->HDMI adapter, to fail on the original NV50.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Previously center scaling would get scaling applied to it (when it was
only supposed to center the image), and aspect-corrected scaling did not
always correctly pick whether to reduce width or height for a particular
combination of inputs/outputs.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110660Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Higher layers tend to add a lot of modes not actually in the EDID, such
as the standard DMT modes. Changing this would be extremely intrusive to
everyone, so just force the scaler more often. There are no practical
cases we're aware of where a LVDS/eDP panel has multiple resolutions
exposed, and i915 already does it this way.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110660Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fix a crash or broken depth testing in all OpenGL applications that use the
depth buffer on MCP89 (GeForce 320M) seen on a MacBook Pro Late 2010.

The bug is tracked in https://bugs.freedesktop.org/show_bug.cgi?id=108500Signed-off-by: NTimo Wiren <timo.wiren@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

In case of error, the function of_get_mac_address() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -ENOMEM from the dmam_alloc_coherent() error
handling case instead of 0, as done elsewhere in this function.

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range.  This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.

On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.

The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:

    $ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
    248

Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.

This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:

    # scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
    add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
    Data                                         old     new   delta
    sysctl_vals                                    -      12     +12
    __kstrtab_sysctl_vals                          -      12     +12
    max                                           14      10      -4
    int_max                                       16       -     -16
    one                                           68       -     -68
    zero                                         128      28    -100
    Total: Before=20583249, After=20583085, chg -0.00%

[mcroce@redhat.com: tipc: remove two unused variables]
  Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
  Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.comSigned-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NAaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>