Unlike their older siblings, ICH6 and 7 use different scheme for MAP
VALUE.  This patch makes ata_piix interpret MV properly on ICH6/7.

Pre-ICH6/7

 The value of these bits indicate the address range the SATA port
 responds to, and whether or not the SATA and IDE functions are
 combined.

 000 = Non-combined. P0 is primary master. P1 is secondary master.
 001 = Non-combined. P0 is secondary master. P1 is primary master.
 100 = Combined. P0 is primary master. P1 is primary slave. P-ATA is
       2:0 Map Value secondary.
 101 = Combined. P0 is primary slave. P1 is primary master. P-ATA is
       secondary.
 110 = Combined. P-ATA is primary. P0 is secondary master. P1 is
       secondary slave.
 111 = Combined. P-ATA is primary. P0 is secondary slave. P1 is
       secondary master.

ICH6/7

 Map Value - R/W. Map Value (MV): The value in the bits below indicate
the address range the SATA ports responds to, and whether or not the
PATA and SATA functions are combined. When in combined mode, the AHCI
memory space is not available and AHCI may not be used.

 00 = Non-combined. P0 is primary master, P2 is the primary slave. P1
      is secondary master, P3 is the 1:0 secondary slave (desktop
      only). P0 is primary master, P2 is the primary slave (mobile
      only).
 01 = Combined. IDE is primary. P1 is secondary master, P3 is the
      secondary slave. (desktop only)
 10 = Combined. P0 is primary master. P2 is primary slave. IDE is secondary
 11 = Reserved
Signed-off-by: NTejun Heo <htejun@gmail.com>

--

Jeff, without this patch, ata_piix misdetects my ICH7's combined mode,
ending up not applying bridge limits to PX-710SA and configuring IDE
drive on 40-c cable to UDMA/66.

Thanks.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

a page while we are still submitting other buffers on the same page for
I/O.

SGI-PV: 948197
SGI-Modid: xfs-linux-melb:xfs-kern:25004a
Signed-off-by: NDavid Chinner <dgc@sgi.com>
Signed-off-by: NNathan Scott <nathans@sgi.com>

sparse can't parse a struct definition in include/asm-powerpc/lppaca.h,
even though gcc can accept it.  The form looks like this:

        struct __attribute__((whatever)) foo { };

An equivalent that both gcc and sparse can handle is

        struct foo { } __attribute__((whatever));

This is the only definition of this type in the tree, and fixing it is
easier than fixing sparse.
Signed-off-by: NBryan O'Sullivan <bos@serpentine.com>
[ Side note: fixing sparse wouldn't be hard, but the "attribute at the
  end" version is the canonical one, and the one that makes sense. So
  let's just fix the kernel instead. Luc Van Oostenryck already sent
  out a sparse patch to the sparse mailing list in case anybody cares.
               -- Linus ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Separate out ahci_dev_classify().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Separate out ahci_stop/start_engine().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Separate out sata_print_link_status() from __sata_phy_reset().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NAlan Cox <alan@redhat.com>

Somewhat cleaner in the resync as someone cleaned up the pio xfer users
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

libata new debugging macro definitions
Signed-off-by: NBorislav Petkov <petkov@uni-muenster.de>
Signed-off-by: NRandy Dunlap <randy_d_dunlap@linux.intel.com>

Signed-off-by: NJason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

sizeof() return is not an int, so use max_t to get the types right.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Be more careful about transmit locking, this solves a possible race
between tx_complete and transmit, that would cause a tx timeout.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't need to inline quite so many routines, let the compiler
decide
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Can use kzalloc here.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: NStephen Hemminger <shemminger@osdl.or>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't need to zero out the status ring entries after processing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Be more careful about memory barriers. The only place we really
need them is before and after updating the chip's ring interface.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Version update.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Need to call pci_set_consistent_dma_mask in the case of 64 bit
DMA.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Need to make sure that sky2 receive buffers are 64 bit
aligned. Also, don't need to start off with GFP_ATOMIC
on initial setup.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

e100: e100 whitespace fixes

These are whitespace only fixes.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

e100: Handle the return values from pci_* functions

This is to resolve warnings during compile time.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue)

Set the end of list bit to cause the hardware's transmit state machine to
work correctly and not prevent management (BMC) traffic.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sbusfb_compat_ioctl() needs to return int, not long, as that
is what the fb_ops->fb_compat_ioctl method prototype wants.

Need to git rid of the "struct file *file" first argument to
fbiogetputcmap() and fbiogscursor() to match calls done in
sbusfb_compat_ioctl().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch changes if() BUG(); constructs
in iommu.c to BUG_ON(); so it gets save
to define BUG() and BUG_ON() to nullstatements.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure a consistent value is read from the STICK register by ensuring
that both high and low are read without high changing due to a roll
over of the low register.

Various Debian/SPARC users (myself include) have noticed problems with
Hummingbird based systems. The symptoms are that the system time is
seen to jump forward 3 days, 6 hours, 11 minutes give or take a few
seconds. In many cases the system then hangs some time afterwards.

I've spotted a race condition in the code to read the STICK register.
I could not work out why 3d, 6h, 11m is important but guess that it is
due to the 2^32 jump of STICK (forwards on one read and then the next
read will seem to be backwards) during a timer interrupt. I'm guessing
that a change of -2^32 will get converted to a large unsigned
increment after the arithmetic manipulation between STICK,
nanoseconds, jiffies etc.

I did a test where I modified __hbird_read_stick to artificially
inject rollover faults forcefully every few seconds. With this I saw
the clock jump over 6 times in 12 hours compared to once every month
or so.
Signed-off-by: NRichard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>