Add IEEE80211_HE_VHT_MAX_AMPDU_FACTOR and IEEE80211_HE_HT_MAX_AMPDU_FACTOR
as per spec to use for peer max ampdu factor.
Signed-off-by: NTamizh Chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1588611900-21185-1-git-send-email-tamizhr@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

These are found in IEEE-802.11ah-2016.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-5-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

If the driver advertises NL80211_EXT_FEATURE_SCAN_FREQ_KHZ
userspace can omit NL80211_ATTR_SCAN_FREQUENCIES in favor
of an NL80211_ATTR_SCAN_FREQ_KHZ. To get scan results in
KHz userspace must also set the
NL80211_SCAN_FLAG_FREQ_KHZ.

This lets nl80211 remain compatible with older userspaces
while not requring and sending redundant (and potentially
incorrect) scan frequency sets.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-4-thomas@adapt-ip.com
[use just nla_nest_start() (not _noflag) for NL80211_ATTR_SCAN_FREQ_KHZ]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

cfg80211 recently gained the ability to understand a
frequency offset component in KHz. Expose this in nl80211
through the new attributes NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET, and
NL80211_BSS_FREQUENCY_OFFSET.

These add support to send and receive a KHz offset
component with the following NL80211 commands:

- NL80211_CMD_FRAME
- NL80211_CMD_GET_SCAN
- NL80211_CMD_AUTHENTICATE
- NL80211_CMD_ASSOCIATE
- NL80211_CMD_CONNECT

Along with any other command which takes a chandef, ie:

- NL80211_CMD_SET_CHANNEL
- NL80211_CMD_SET_WIPHY
- NL80211_CMD_START_AP
- NL80211_CMD_RADAR_DETECT
- NL80211_CMD_NOTIFY_RADAR
- NL80211_CMD_CHANNEL_SWITCH
- NL80211_JOIN_IBSS
- NL80211_CMD_REMAIN_ON_CHANNEL
- NL80211_CMD_JOIN_OCB
- NL80211_CMD_JOIN_MESH
- NL80211_CMD_TDLS_CHANNEL_SWITCH

If the driver advertises a band containing channels with
frequency offset, it must also verify support for
frequency offset channels in its cfg80211 ops, or return
an error.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-3-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.

This doesn't actually change the nl80211 API yet.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
 drop trace point name changes]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current rule for applying TID configuration for specific peer looks overly
complicated. No need to reject new TID configuration when override flag is
specified. Another call with the same TID configuration, but without
override flag, allows to apply new configuration anyway.

Use the same approach as for the 'all peers' case: if override flag is
specified, then reset existing TID configuration and immediately
apply a new one.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-5-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds support to control per TID MSDU aggregation
using the NL80211_TID_CONFIG_ATTR_AMSDU_CTRL attribute.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-4-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix all variable names from 'tid' to 'tids' to avoid confusion.
Now this is not TID number, but TID mask.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-3-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

TIDs mask type is u64 in wiphy settings and nl80211 processing, see:
- wiphy TIDs mask sizes in tid_config_support structure
- prepare driver command in parse_tid_conf

Use the same type for TIDs mask in cfg80211_tid_cfg.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-2-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.

Only the ATH9331 was tested with this patch.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Raw PHY TDR data

Some ethernet PHYs allow access to raw TDR data in addition to summary
diagnostics information. Add support for retrieving this data via
netlink ethtool. The basic structure in the core is the same as for
normal phy diagnostics, the PHY driver simply uses different helpers
to fill the netlink message with different data.

There is a graphical tool under development, as well a ethtool(1)
which can dump the data as text and JSON.

A patched ethtool(1) can be found in
https://github.com/lunn/ethtool.git feature/cable-test-v5

Thanks for Chris Healy for lots of testing.

v2:
See the individual patches but:

Pass distances in centimeters, not meters

Allow the PHY to round distances to what it supports and report what
it actually used along with the results.

Make the Marvell PHY use steps a multiple of 0.805 meters, its native
step size.

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Unsquash the last two patches
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.

If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Ethernet PHYs can return the raw time domain reflectromatry data.
Add the attributes to allow this data to be requested and returned via
netlink ethtool.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v2:
m -> cm
Report what the PHY actually used for start/stop/step.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: NArmin Wolf <W_Armin@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ignore loopback-originatig packets soon enough and don't try to process L2
header where it doesn't exist. The very similar br_handle_frame() in bridge
code performs exactly the same check.

This is an example of such ICMPv6 packet:

skb len=96 headroom=40 headlen=96 tailroom=56
mac=(40,0) net=(40,40) trans=80
shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
csum(0xae2e9a2f ip_summed=1 complete_sw=0 valid=0 level=0)
hash(0xc97ebd88 sw=1 l4=1) proto=0x86dd pkttype=5 iif=24
dev name=etha01.212 feat=0x0x0000000040005000
skb headroom: 00000000: 00 7c 86 52 84 88 ff ff 00 00 00 00 00 00 08 00
skb headroom: 00000010: 45 00 00 9e 5d 5c 40 00 40 11 33 33 00 00 00 01
skb headroom: 00000020: 02 40 43 80 00 00 86 dd
skb linear:   00000000: 60 09 88 bd 00 38 3a ff fe 80 00 00 00 00 00 00
skb linear:   00000010: 00 40 43 ff fe 80 00 00 ff 02 00 00 00 00 00 00
skb linear:   00000020: 00 00 00 00 00 00 00 01 86 00 61 00 40 00 00 2d
skb linear:   00000030: 00 00 00 00 00 00 00 00 03 04 40 e0 00 00 01 2c
skb linear:   00000040: 00 00 00 78 00 00 00 00 fd 5f 42 68 23 87 a8 81
skb linear:   00000050: 00 00 00 00 00 00 00 00 01 01 02 40 43 80 00 00
skb tailroom: 00000000: ...
skb tailroom: 00000010: ...
skb tailroom: 00000020: ...
skb tailroom: 00000030: ...

Call Trace, how it happens exactly:
 ...
 macvlan_handle_frame+0x321/0x425 [macvlan]
 ? macvlan_forward_source+0x110/0x110 [macvlan]
 __netif_receive_skb_core+0x545/0xda0
 ? enqueue_task_fair+0xe5/0x8e0
 ? __netif_receive_skb_one_core+0x36/0x70
 __netif_receive_skb_one_core+0x36/0x70
 process_backlog+0x97/0x140
 net_rx_action+0x1eb/0x350
 ? __hrtimer_run_queues+0x136/0x2e0
 __do_softirq+0xe3/0x383
 do_softirq_own_stack+0x2a/0x40
 </IRQ>
 do_softirq.part.4+0x4e/0x50
 netif_rx_ni+0x60/0xd0
 dev_loopback_xmit+0x83/0xf0
 ip6_finish_output2+0x575/0x590 [ipv6]
 ? ip6_cork_release.isra.1+0x64/0x90 [ipv6]
 ? __ip6_make_skb+0x38d/0x680 [ipv6]
 ? ip6_output+0x6c/0x140 [ipv6]
 ip6_output+0x6c/0x140 [ipv6]
 ip6_send_skb+0x1e/0x60 [ipv6]
 rawv6_sendmsg+0xc4b/0xe10 [ipv6]
 ? proc_put_long+0xd0/0xd0
 ? rw_copy_check_uvector+0x4e/0x110
 ? sock_sendmsg+0x36/0x40
 sock_sendmsg+0x36/0x40
 ___sys_sendmsg+0x2b6/0x2d0
 ? proc_dointvec+0x23/0x30
 ? addrconf_sysctl_forward+0x8d/0x250 [ipv6]
 ? dev_forward_change+0x130/0x130 [ipv6]
 ? _raw_spin_unlock+0x12/0x30
 ? proc_sys_call_handler.isra.14+0x9f/0x110
 ? __call_rcu+0x213/0x510
 ? get_max_files+0x10/0x10
 ? trace_hardirqs_on+0x2c/0xe0
 ? __sys_sendmsg+0x63/0xa0
 __sys_sendmsg+0x63/0xa0
 do_syscall_64+0x6c/0x1e0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various trap changes - part 2

This patch set contains another set of small changes in mlxsw trap
configuration. It is the last set before exposing control traps (e.g.,
IGMP query, ARP request) via devlink-trap.

Tested with existing devlink-trap selftests. Please see individual
patches for a detailed changelog.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.

However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.

To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).

This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.

Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.

As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.

Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the previous patch the split is no longer necessary and all the
trap groups can be moved under the same enum.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in commit e6125230 ("mlxsw: spectrum_trap: Introduce
dummy group with thin policer"), the purpose of the "thin" policer is to
pass as less packets as possible to the CPU.

The identifier of this policer is currently set according to the maximum
number of used trap groups, but this is fragile: On Spectrum-1 the
maximum number of policers is less than the maximum number of trap
groups, which might result in an invalid policer identifier in case the
number of used trap groups grows beyond the policer limit.

Solve this by dynamically allocating the policer identifier.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.

In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.

These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Group these various IPv6 packets (e.g., router solicitations, router
advertisement) together and subject them to the same policer.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trap groups that use the same policer settings can share the same switch
case.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets that are trapped via tc's trap action are currently subject to
the same policer as packets hitting local routes. The latter are
critical to the correct functioning of the control plane, while the
former are mainly used for traffic inspection.

Split the ACL trap to a separate group with its own policer. Use a
higher priority for these traps than for traps using mirror action
(e.g., ARP, IGMP). Otherwise, packets matching both traps will not be
forwarded in hardware (because of trap action) and also not forwarded in
software because they will be marked with 'offload_fwd_mark'.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can try to coalesce skbs we take from the subflows rx queue with the
tail of the mptcp rx queue.

If successful, the skb head can be discarded early.

We can also free the skb extensions, we do not access them after this.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't call netif_napi_del() manually, free_netdev() does this for us.
In addition reorder calls to match reverse order of calls in probe().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fugang Duan says:

====================
net: ethernet: fec: move GPR register offset and bit into DT

The commit da722186 (net: fec: set GPR bit on suspend by
DT configuration) set the GPR reigster offset and bit in driver
for wol feature support.

It brings trouble to enable wol feature on imx6sx/imx6ul/imx7d
platforms that have multiple ethernet instances with different
GPR bit for stop mode control. So the patch set is to move GPR
register offset and bit define into DT, and enable imx6q/imx6dl
imx6qp/imx6sx/imx6ul/imx7d stop mode support.

Currently, below NXP i.MX boards support wol:
- imx6q/imx6dl/imx6qp sabresd
- imx6sx sabreauto
- imx7d sdb

imx6q/imx6dl/imx6qp sabresd board dts file miss the property
"fsl,magic-packet;", so patch#4 is to add the property for stop
mode support.

v1 -> v2:
 - driver: switch back to store the quirks bitmask in driver_data
 - dt-bindings: rename 'gpr' property string to 'fsl,stop-mode'
 - imx6/7 dtsi: add imx6sx/imx6ul/imx7d ethernet stop mode property
v2 -> v3:
 - driver: suggested by Sascha Hauer, use a struct fec_devinfo for
   abstracting differences between different hardware variants,
   it can give more freedom to describe the differences.
 - imx6/7 dtsi: correct one typo pointed out by Andrew.

Thanks Martin, Andrew and Sascha Hauer for the review.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Update the imx6qdl gpr property to define gpr register
  offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>