These new helpers + macro definitions are meant to replace the old ones
which are unpractical to use.

Note that the macros and function prefixes have been intentionally
changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that
this IP is also embedded in avr32 SoCs (and not only in at91 ones).
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

devm_ioremap_resource does checks on the resource. No need to
duplicate this in the driver.
Signed-off-by: NBelén Sarabia <belensarabia@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

POWERHOLD signal has higher priority  over the DEV_ON bit.
So power off will not happen if the POWERHOLD is held high.
Hence reset the MUX to GPIO_7 mode to release the POWERHOLD
and the DEV_ON bit to take effect to power off the PMIC.

PMIC Power off happens in dire situations like thermal shutdown
so irrespective of the POWERHOLD setting go ahead and turn off
the powerhold.  Currently poweroff is broken on boards that have
powerhold enabled. This fixes poweroff on those boards.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The tc6393xb mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel.  Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.

A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: NJulia Cartwright <julia@ni.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The t7l66xb mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel.  Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.

A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: NJulia Cartwright <julia@ni.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The asic3 mfd driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel.  Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.

A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: NJulia Cartwright <julia@ni.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

For better understanding of relationship between headers and modules
rename:
	intel_bxtwc.h -> intel_soc_pmic_bxtwc.h

While here, remove file name from the file itself.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There is no need to include intel_soc_pmic.h into header which doesn't
require it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently, we specify the timeout in terms of the number of polls but it
is more clear from a user of the functions perspective to specify the
timeout directly in milliseconds, as such update the function to these new
semantics.

Additionally, arizona_poll_reg essentially hard-codes
regmap_read_poll_timeout, update the implementation to use
regmap_read_poll_timeout. We still keep arizona_poll_reg around as
regmap_read_poll_timeout is a macro so rather than expand this for each
caller keep it wrapped in arizona_poll_reg.

Whilst we are doing this make the timeouts a little more generous as
the previous system had a bit more slack as it was done as a delay per
iteration of the loop whereas regmap_read_poll_timeout compares ktime's.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Register addresses are normally displayed in hex throughout the Arizona
driver. Update the arizona_poll_reg function to follow this convention.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

arizona_poll_reg already returns ETIMEDOUT if we don't see the expected
register changes before the time out, so remove pointless local setting of
ETIMEDOUT.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To enable eventual removal of pr_warning

This makes pr_warn use consistent for drivers/mfd

Prior to this patch, there were 4 uses of pr_warning and
9 uses of pr_warn in drivers/mfd
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Align the placement as which the mfd_cell of LED is defined as the other
members done on the structure.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds description for LED as the sub-module on MT6397/MT6323
multifunction device.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The CHRG_CTRL1 and CHRG_CTRL2 registers are made for controlling
different battery charging settings such as the constant current charge
value.

The AXP22X also have a third register CHRG_CTRL3 which has settings for
battery charging too.

This adds the CHRG_CTRL1, CHRG_CTRL2 and CHRG_CTRL3 registers to the
list of writeable registers for AXP20X and AXP22X PMICs.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The X-Powers AXP20X and AXP22X PMICs expose the status of AC power
supply.

This adds the AC power supply driver to the MFD cells of the AXP22X
PMICs.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-By: NSebastian Reichel <sre@kernel.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds the AXP20X/AXP22x ADCs driver to the mfd cells of the AXP209,
AXP221 and AXP223 MFD.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The registers 0x56 and 0x57 of AXP22X PMIC store the value of the
internal temperature of the PMIC.

This patch modifies the name of these registers from AXP22X_PMIC_ADC_H/L
to AXP22X_PMIC_TEMP_H/L so their purpose is clearer.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The SPI interface is mostly a copy/paste from the I2C interface with some
minor renaming for consistency. "Client" is an I2C specific term that
was left in the SPI remove path, rename this here.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds documentation for the Altera A10-SR Reset
Controller DT bindings.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add Peripheral PHY Reset Controller to the Arria10
Development Kit System Resource Chip's MFD.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

After commit 028af594 ("mfd: intel-lpss: Pass SDA hold time to
I2C host controller driver") the driver still has a non-used variable.

Remove it here.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is a sucky change to bump up the time we'll wait for the EC.  Why
is it sucky?  If 200ms for a transfer is a common thing it will have a
massively bad impact on keyboard responsiveness.

It still seems like a good idea to do this, though, because we have a
gas gauge that claims that in an extreme case it could stretch the i2c
clock for 144ms.  It's not a common case so it shouldn't affect
responsiveness, but it can happen.  It's much better to have a single
slow keyboard response than to start returning errors when we don't
have to.

In newer EC designs we should probably implement a virtual battery to
respond to the kernel to insulate the kernel from these types of
issues.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

TI LMU (Lighting Management Unit) driver supports lighting devices below.

  LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.

LMU devices have common features.
  - I2C interface for accessing device registers
  - Hardware enable pin control
  - Backlight brightness control
  - Notifier for hardware fault monitoring
  - Regulators for LCD display bias

It contains fault monitor, backlight, LED and regulator driver.

LMU fault monitor
-----------------
  LM3633 and LM3697 provide hardware monitoring feature.
  It enables open or short circuit detection.
  After monitoring is done, each device should be re-initialized.
  Notifier is used for this case.
  Separate patch for 'ti-lmu-fault-monitor' will be sent later.

Backlight
---------
  It's handled by TI LMU backlight consolidated driver and
  chip dependent data. Separate patchset will be sent later.

LED indicator
-------------
  LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
  supported. Separate patch for 'leds-lm3633' will be sent later.

Regulator
---------
  LM3631 has 5 regulators for the display bias.
  LM3632 supports 3 regulators. One consolidated driver enables it.
  The lm363x regulator driver is already upstreamed.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch describes overall binding for TI LMU MFD devices.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Acked-by: NRob Herring <robh+dt@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. This patch lets the driver use the new device tree property
"xpowers,master-mode" to set the correct operating mode for the board.

Fixes: 8824ee85 ("mfd: axp20x: Add support for AXP806 PMIC")
Signed-off-by: NRask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".

Fixes: 204ae296 ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: NRask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since commit 845c8770 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") I2C core assigns interrupt line to I2C slave
devices with regarding to GpioInt() resources.

There is no need to repeat this in the driver.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

STM32 timers register bank size is 0x400. Fix regmap max_register.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It is a debugging statement so make it be issued only then.

No functionality change.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

At least two different omap3630/3730 boards booting from MMC1
fail to reboot if the "ti,twl4030-power-idle-osc-off" or
"ti,twl4030-power-idle" compatible flags are set.  This patch will
keep the vmmc1 powered up during reboot allowing the bootloader
to load.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add missing of_platform_depopulate() upon driver removal.
Signed-off-by: NFabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patches adds the first minimal support to the upstream Linux tree.
Signed-off-by: NPriyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: NArchana Patni <archana.patni@intel.com>
Signed-off-by: NThierry Escande <thierry.escande@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-gpio-4.12', 'ib-mfd-iio-input-4.12', 'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged

Motorola CPCAP is a PMIC found in multiple smartphones.
This driver adds support for the power/on button and has
been tested in Droid 4.
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

CPCAP can sense if IRQ is currently set or not. This
functionality is required for a few subdevices, such
as the power button and usb phy modules.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This fixes compilation for files, that try to include the
cpcap header in alphabetically sorted #include lists.
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds support for retention control for Exynos5433 SoCs. Three
groups of pins has been defined for retention control: common shared group
for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and
separate control for FSYS and AUD pin banks, for which PMU retention
registers match whole banks.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

When pin controller device is a part of power domain, there is no guarantee
that the power domain was not turned off and then on during boot process
before probing of the pin control driver. If it happened, then pin control
driver should ensure that pad retention is turned off during its probe call.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>