bnxt_fw_reset_task() which runs from a workqueue can race with
bnxt_remove_one().  For example, if firmware reset and VF FLR are
happening at about the same time.

bnxt_remove_one() already cancels the workqueue and waits for it
to finish, but we need to do this earlier before the devlink
reporters are destroyed.  This will guarantee that
the devlink reporters will always be valid when bnxt_fw_reset_task()
is still running.

Fixes: b148bb23 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When the driver goes through PCIe AER reset in error state, all
firmware messages will timeout because the PCIe bus is no longer
accessible.  This can lead to AER reset taking many minutes to
complete as each firmware command takes time to timeout.

Define a new macro BNXT_NO_FW_ACCESS() to skip these firmware messages
when either firmware is in fatal error state or when
pci_channel_offline() is true.  It now takes a more reasonable 20 to
30 seconds to complete AER recovery.

Fixes: b4fff207 ("bnxt_en: Do not send firmware messages if firmware is in error state.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled.  A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.

Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails.  tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails.  We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task().  Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: NDavid Christensen <drc@linux.vnet.ibm.com>
Reported-by: NBaptiste Covolato <baptiste@arista.com>
Fixes: db219973 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VALIDATE_MASK(eth_mask->h_source) is checked twice in a row in
bcmgenet_validate_flow(). Add VALIDATE_MASK(eth_mask->h_dest)
instead.

Fixes: 3e370952 ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: NDenis Efremov <efremov@linux.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:

 BUG: kernel NULL pointer dereference, address: 0000000000000000
 CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S                5.9.0-rc1-00469-g5fd99b5d-dirty #26
 RIP: 0010:bnxt_poll+0x121/0x1c0
 Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
  netpoll_poll_dev+0xbd/0x1a0
  __netpoll_send_skb+0x1b2/0x210
  netpoll_send_udp+0x2c9/0x406
  write_ext_msg+0x1d7/0x1f0
  console_unlock+0x23c/0x520
  vprintk_emit+0xe0/0x1d0
  printk+0x58/0x6f
  x86_vector_activate.cold+0xf/0x46
  __irq_domain_activate_irq+0x50/0x80
  __irq_domain_activate_irq+0x32/0x80
  __irq_domain_activate_irq+0x32/0x80
  irq_domain_activate_irq+0x25/0x40
  __setup_irq+0x2d2/0x700
  request_threaded_irq+0xfb/0x160
  __bnxt_open_nic+0x3b1/0x750
  bnxt_open_nic+0x19/0x30
  ethtool_set_channels+0x1ac/0x220
  dev_ethtool+0x11ba/0x2240
  dev_ioctl+0x1cf/0x390
  sock_do_ioctl+0x95/0x130
Reported-by: NRob Sherwood <rsher@fb.com>
Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved.  If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all.  In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.

Fix both issues in bnxt_need_reserve_rings().  In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.

Without valid RSS map, the NIC won't receive packets properly.

Fixes: 1667cbf6 ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.

Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.

Fixes: bd3191b5 ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.

The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.

Fixes: cde49a42 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: NMarc Smith <msmith626@gmail.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_fw_reset_task() is run from a delayed workqueue.  The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.

The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one().  bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling.  This
will guarantee that no rescheduling will be done after it is cancelled.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.

Fixes: 6316ea6d ("bnxt_en: Enable AER support.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled.  In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count.  As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only.  This causes ethtool -S to
display extra counters with no counter names.

Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.

Fixes: 125592fb ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.

Fixes: db4723b3 ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.

Fixes: 7b78be48 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

Fixes coccicheck warning:

./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory,  so memset is not needed

dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NLi Heng <liheng40@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to dump PXP registers and PCIe statistics.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide.  Define the necessary macros to access the software
counters.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.

A chip bug was also discovered that could cause some ring counters to
become 0 during DMA.  Workaround by ignoring zeros on the affected
chips.

Some older frimware will reset port counters during ifdown.  We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If supported by newer firmware, make the firmware call to query all
the port counter masks.  If not supported, assume 40-bit port
counter masks.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters.  Make this call when supported to
initialize the hardware masks of all ring counters.  If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow.  Allocate copies of these
DMA statistics memory blocks with the same size for accumulation.  The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same.  Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.

Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding.  The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.

v2: Fix bnxt_re compile error.

Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump.  The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.

There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.

This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().

This patch was compile-tested on allyesconfig.
Signed-off-by: NAndrii Nakryiko <andriin@fb.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com

One-element arrays are being deprecated[1]. Replace the one-element
array with a simple value type 'u32 reserved2'[2], once it seems
this is just a placeholder for alignment.

[1] https://github.com/KSPP/linux/issues/79
[2] https://github.com/KSPP/linux/issues/86Tested-by: Nkernel test robot <lkp@intel.com>
Link: https://github.com/GustavoARSilva/linux-hardening/blob/master/cii/0-day/tg3-20200718.mdSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().

Fix to goto err_clk_disable if clk_prepare_enable() is successful.

Fixes: c80d36ff ("net: bcmgenet: Use devm_clk_get_optional() to get the clocks")
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().

Fix to goto err_clk_disable if clk_prepare_enable() is successful.

Fixes: 99d55638 ("net: bcmgenet: enable NETIF_F_HIGHDMA flag")
Signed-off-by: NZhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fact that NETIF_F_HW_TC is not set should be a sufficient
indication to the user that TC offloads are not supported.
No need to bother users of older firmware versions with
pointless warnings on every boot.

Also, since the support is optional, bnxt_init_tc() should not
return an error in case FW is old, similarly to how error
is not returned when CONFIG_BNXT_FLOWER_OFFLOAD is not set.

With that we can add an error message to the caller, to warn
about actual unexpected failures.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.

This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.

Fixes: f50932cc ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.

This commit adds a check of the RBUF_ACPI_EN flag when Wake
on Filter is enabled. A clear flag indicates that the GENET
hardware must have been reset so the remainder of the
hardware programming is bypassed.

Fixes: f50932cc ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.

This commit adds a check of the MPD_EN flag when Wake on
Magic Packet is enabled. A clear flag indicates that the
GENET hardware must have been reset so the remainder of the
hardware programming is bypassed.

Fixes: 1a1d5106 ("net: bcmgenet: move clk_wol management to bcmgenet_wol")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.

In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:

git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
	xargs perl -pi -e \
		's/\buninitialized_var\(([^\)]+)\)/\1/g;
		 s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'

drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.

No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.

[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/

Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: NKees Cook <keescook@chromium.org>

Fairly straightforward conversion - no need to keep track
of the use count, and replay when ports get removed, also
callbacks can just sleep.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.

To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current completion ring sizing formula is wrong with TPA enabled.
The formula assumes that the number of TPA completions are bound by the
RX ring size, but that's not true.  TPA_START completions are immediately
recycled so they are not bound by the RX ring size.  We must add
bp->max_tpa to the worst case maximum RX and TPA completions.

The completion ring can overflow because of this mistake.  This will
cause hardware to disable the completion ring when this happens,
leading to RX and TX traffic to stall on that ring.  This issue is
generally exposed only when the RX ring size is set very small.

Fix the formula by adding bp->max_tpa to the number of RX completions
if TPA is enabled.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.");
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a shared port PHY configuration, async event is received when any of the
port modifies the configuration. Ethtool link settings should be
initialised after updated PHY configuration from firmware.

Fixes: b1613e78 ("bnxt_en: Add async. event logic for PHY configuration changes.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was modified to not rely on rtnl lock to protect link
settings about 2 years ago.  The pause setting was missed when
making that change.  Fix it by acquiring link_lock mutex before
calling bnxt_hwrm_set_pause().

Fixes: e2dc9b6e ("bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>