This patch adds support to the JESD216 rev B standard and parses the SFDP
tables to dynamically initialize the 'struct spi_nor_flash_parameter'.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@microchip.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>

This patch starts adding support to Octo SPI protocols (SPI x-y-8).

Op codes for Fast Read and/or Page Program operations using Octo SPI
protocols are not known yet (no JEDEC specification has defined them yet)
but we'd rather introduce the Octo SPI protocols now so it's done as it
should be.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>

This patch introduces support to Double Transfer Rate (DTR) SPI protocols.
DTR is used only for Fast Read operations.

According to manufacturer datasheets, whatever the number of I/O lines
used during instruction (x) and address/mode/dummy (y) clock cycles, DTR
is used only during data (z) clock cycles of SPI x-y-z protocols.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>

This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.

Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.

Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.

1 - spi_nor_init_params()

The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.

2 - spi_nor_setup()

The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>

This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.

The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.

This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>

Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
their configuration data and (optionally) some user data.

The protocol of this flash follows most of the spi-nor standard. With
the following differences:

- Page size might not be a power of two.
- The address calculation (default addressing mode).
- The spi nor commands used.

Protocol is described on Xilinx User Guide UG333
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>

Do not pass retlen to hardware driver read/write functions. Update it in
spi-nor generic driver instead.
Signed-off-by: NMichal Suchanek <hramrach@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NMichal Suchanek <hramrach@gmail.com>
Tested-by: NMichal Suchanek <hramrach@gmail.com>

Change the return value of spi-nor device read and write methods to
allow returning amount of data transferred and errors as
read(2)/write(2) does.

Also, start handling positive returns in spi_nor_read(), since we want
to convert drivers to start returning the read-length both via *retlen
and the return code. (We don't need to do the same transition process
for spi_nor_write(), since ->write() didn't used to have a return code
at all.)
Signed-off-by: NMichal Suchanek <hramrach@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NMichal Suchanek <hramrach@gmail.com>
Tested-by: NMichal Suchanek <hramrach@gmail.com>

Also note the GigaDevice JEDEC ID.

No write-protect support yet, since this flash uses a different status
register layout.

Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NMarek Vasut <marex@denx.de>

Some flash support a bit in the status register that inverts protection
so that it applies to the bottom of the flash, not the top. This yields
additions to the protection range table, as noted in the comments.

Because this feature is not universal to all flash that support
lock/unlock, control it via a new flag.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>

Spansion and Winbond have occasionally used the same manufacturer ID,
and they don't support the same features. Particularly, writing SR=0
seems to break read access for Spansion's s25fl064k. Unfortunately, we
don't currently have a way to differentiate these Spansion and Winbond
parts, so rather than regressing support for these Spansion flash, let's
drop the new Winbond lock/unlock support for now. We can try to address
Winbond support during the next release cycle.

Original discussion:

http://patchwork.ozlabs.org/patch/549173/
http://patchwork.ozlabs.org/patch/553683/

Fixes: 357ca38d ("mtd: spi-nor: support lock/unlock/is_locked for Winbond")
Fixes: c6fc2171 ("mtd: spi-nor: disable protection for Winbond flash at startup")
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reported-by: NFelix Fietkau <nbd@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>

So far struct spi_nor was using just a pointer to struct mtd_info so it
wasn't needed to have it fully defined there. After recent change we
embed whole struct so we need to include a proper header.

Fixes: 19763671 ("mtd: spi-nor: embed struct mtd_info within struct spi_nor")
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Some spi-nor drivers perform sector erase by duplicating their
write_reg() command. Let's not require that the driver fill this out,
and provide a default instead.

Tested on m25p80.c and Medatek's MT8173 SPI NOR flash driver.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We can just alias to the MTD of_node.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

We are going to begin using the mtd->dev.of_node field for MTD device
nodes, so let's add helpers for it. Also, we'll be making some
conversions on spi_nor (and nand_chip eventually) too, so get that ready
with their own helpers.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

This enables ioctl(MEMISLOCKED). Status can now be reported in the
mtdinfo or flash_lock utilities found in mtd-utils.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

I got the names of these fields wrong.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

These are often similar for CFI (parallel NOR) and for SPI NOR, but they
aren't always the same, for various reasons (different namespaces,
company acquisitions and renames, etc.). And some don't have CFI_MFR_*
entries at all.

So let's make a proper place to list the SPI NOR IDs, with all the SPI
NOR specific assumptions and comments.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

These status bits use different ways of representing similar integer
constants -- some are decimal, some are hex. Make them more consistent.

At the same time, impose my own preference, since IMO it's clearer what
these are when using the BIT() macro.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We use BIT() in the header. No real problem for now, but it's better to
be accurate.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

struct spi_nor_xfer_cfg and read_xfer/write_xfer hooks were never used by
any driver. Do some cleanup by removing them.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The 'write_enable' argument is unused and unneeded, so remove it from
the API.
Signed-off-by: NJagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Han Xu <han.xu@freescale.com>
[Brian: fixed for nxp-spifi.c]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The problem this patch is trying to address is such, that SPI NOR flash
devices attached to a dedicated SPI NOR controller cannot read their
properties from the associated struct device_node.

A couple of facts first:
1) Each SPI NOR flash has a struct spi_nor associated with it.
2) Each SPI NOR flash has certain device properties associated
   with it, for example the OF property 'm25p,fast-read' is a
   good pick. These properties are used by the SPI NOR core to
   select which opcodes are sent to such SPI NOR flash. These
   properties are coming from spi_nor .dev->of_node .

The problem is, that for SPI NOR controllers, the struct spi_nor .dev
element points to the struct device of the SPI NOR controller, not the
SPI NOR flash. Therefore, the associated dev->of_node also is the
one of the controller and therefore the SPI NOR core code is trying to
parse the SPI NOR controller's properties, not the properties of the
SPI NOR flash.

Note: The m25p80 driver is not affected, because the controller and
      the flash are the same device, so the associated device_node
      of the controller and the flash are the same.

This patch adjusts the SPI NOR core such that the device_node is not
picked from spi_nor .dev directly, but from a new separate spi_nor
.flash_node element. This let's the SPI NOR controller drivers set up
a different spi_nor .flash_node element for each SPI NOR flash.

This patch also fixes the controller drivers to be compatible with
this modification and correctly set the spi_nor .flash_node element.

This patch is inspired by 5844feea
mtd: nand: add common DT init code
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This reflects the proper layering, so let's do it.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>

This header can't actually stand alone, as it relies on the declaration
(but not definition) of struct mtd_info. Let's fix that.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>

Flash lock/unlock is a flash-specific operations. Factor out a callback
for it to more readily support other vendors.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Tested-by: NVIET NGA DAO <vndao@altera.com>

This patch adds code which enables Quad I/O mode on Micron SPI NOR flashes.

For Micron SPI NOR flash, enabling or disabling quad I/O protocol can be
done By two methods, which are to use EVCR (Enhanced Volatile
Configuration Register) and the ENTER QUAD I/O MODE command. There is no
difference between these two methods. Unfortunately, for some Micron SPI
NOR flashes, there no ENTER Quad I/O command (35h), such as n25q064. But
for all current Micron SPI NOR, if it support quad I/O mode, using EVCR
definitely be supported. It is a recommended method to enable Quad I/O
mode by EVCR, Quad I/O protocol bit 7. When EVCR bit 7 is reset to 0,
the SPI NOR flash will operate in quad I/O mode.

This patch has been tested on N25Q512A and MT25TL256BAA1ESF. Micron SPI
NOR of spi_nor_ids[] table all support this method.
Signed-off-by: NBean Huo <beanhuo@micron.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We don't need to expose a 'wait-till-ready' interface to drivers. Status
register polling should be handled by the core spi-nor.c library, and as
of now, I see no need to provide a special driver-specific hook for it.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

spi-nor.c should be taking care of these now.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

There is currently no useful way to override the default
implementation of this operation.  The returned struct spi_device_id
must have a pointer to struct flash_info in its private data, but this
structure is defined inside spi-nor.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

m25p80's device ID table is now spi_nor_ids, defined in spi-nor.  The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time.  Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.

A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.

As a quick fix suitable for stable, copy the device IDs back into
m25p80.

Fixes: 03e296f6 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b38: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce05: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid.  Make spi_nor_scan() do it for them.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Some new Micron flash chips require reading the flag status register to
determine when operations have completed.

Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.

This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: NGraham Moore <grmoore@altera.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

serial_flash_cmds.h defines our opcodes a little differently. Let's
borrow its naming, since it's borrowed from the SFDP standard, and it's
more extensible.

This prepares us for merging serial_flash_cmds.h and spi-nor.h opcode
listing.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NHuang Shijie <b32955@freescale.com>

Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NHuang Shijie <b32955@freescale.com>

Spacing is a little non-standard here. Fix up tabs vs. spaces.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Acked-by: NHuang Shijie <b32955@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

Add the copyright information for spi-nor.c and spi-nor.h.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.

Before this patch, the layer is like:

                   MTD
         ------------------------
                  m25p80
         ------------------------
	       spi bus driver
         ------------------------
	        SPI NOR chip

After this patch, the layer is like:
                   MTD
         ------------------------
                  spi-nor
         ------------------------
                  m25p80
         ------------------------
	       spi bus driver
         ------------------------
	       SPI NOR chip

With the spi-nor controller driver(Freescale Quadspi), it looks like:
                   MTD
         ------------------------
                  spi-nor
         ------------------------
                fsl-quadspi
         ------------------------
	       SPI NOR chip

New APIs:
   spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The spi_nor{} is cloned from the m25p{}.
The spi_nor{} can be used by both the m25p80 and spi-nor controller.

We also add the spi_nor_xfer_cfg{} which can be used by the two
fundamental primitives: read_xfer/write_xfer.

 1) the hooks for spi_nor{}:
    @prepare/unpreare: used to do some work before or after the
             read/write/erase/lock/unlock.
    @read_xfer/write_xfer: We can use these two hooks to code all
             the following hooks if the driver tries to implement them
             by itself.
    @read_reg: used to read the registers, such as read status register,
             read configure register.
    @write_reg: used to write the registers, such as write enable,
             erase sector.
    @read_id: read out the ID info.
    @wait_till_ready: wait till the NOR becomes ready.
    @read: read out the data from the NOR.
    @write: write data to the NOR.
    @erase: erase a sector of the NOR.

 2) Add a new field sst_write_second for the SST NOR write.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>