Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 9月, 2021 1 次提交
  3. 19 9月, 2021 2 次提交
    • V
      net: dsa: tear down devlink port regions when tearing down the devlink port on error · fd292c18
      由 Vladimir Oltean 提交于 
      Commit 86f8b1c0 ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.

Commit fb6ec87f ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.

Commit 08156ba4 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.

When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:

devlink_port_unregister:
	WARN_ON(!list_empty(&devlink_port->region_list));

So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.

Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.

But DSA's layering stays in our way quite badly here.

The options I've considered are:

1. Introduce a function in devlink to just change a port's type and
   flavour. No dice, devlink keeps a lot of state, it really wants the
   port to not be registered when you set its parameters, so changing
   anything can only be done by destroying what we currently have and
   recreating it.

2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
   and the region returned, keep those in a list, then when the devlink
   port unregister needs to take place, the existing devlink regions are
   destroyed by DSA, and we replay the creation of new regions using the
   cached parameters. Problem: mv88e6xxx keeps the region pointers in
   chip->ports[port].region, and these will remain stale after DSA frees
   them. There are many things DSA can do, but updating mv88e6xxx's
   private pointers is not one of them.

3. Just let the driver do it (i.e. introduce a very specific method
   called ds->ops->port_reinit_as_unused, which unregisters its devlink
   port devlink regions, then the old devlink port, then registers the
   new one, then the devlink port regions for it). While it does work,
   as opposed to the others, it's pretty horrible from an API
   perspective and we can do better.

4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
   which in the case of mv88e6xxx must register and unregister the
   devlink port regions. Call these 2 methods when the port must be
   reinitialized as unused.

Naturally, I went for the 4th approach.

Fixes: 08156ba4 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fd292c18
    • V
      net: dsa: be compatible with masters which unregister on shutdown · 0650bf52
      由 Vladimir Oltean 提交于 
      Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.

What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.

This message can be seen in a loop, and it hangs the reboot process there:

unregister_netdevice: waiting for eth0 to become free. Usage count = 3

So why 3?

A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:

dsa_slave_create
-> netdev_upper_dev_link
   -> __netdev_upper_dev_link
      -> __netdev_adjacent_dev_insert
         -> dev_hold

So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.

Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.

It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.

So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.

However, complications arise really quickly.

The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).

Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.

So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.

So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.

The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.

The answer to that question lies in this comment above device_link_add:

 * A side effect of the link creation is re-ordering of dpm_list and the
 * devices_kset list by moving the consumer device and all devices depending
 * on it to the ends of these lists (that does not happen to devices that have
 * not been registered when this function is called).

so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.

Fixes: 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0650bf52
  5. 09 8月, 2021 1 次提交
    • V
      net: dsa: centralize fast ageing when address learning is turned off · 045c45d1
      由 Vladimir Oltean 提交于 
      Currently DSA leaves it down to device drivers to fast age the FDB on a
port when address learning is disabled on it. There are 2 reasons for
doing that in the first place:

- when address learning is disabled by user space, through
  IFLA_BRPORT_LEARNING or the brport_attr_learning sysfs, what user
  space typically wants to achieve is to operate in a mode with no
  dynamic FDB entry on that port. But if the port is already up, some
  addresses might have been already learned on it, and it seems silly to
  wait for 5 minutes for them to expire until something useful can be
  done.

- when a port leaves a bridge and becomes standalone, DSA turns off
  address learning on it. This also has the nice side effect of flushing
  the dynamically learned bridge FDB entries on it, which is a good idea
  because standalone ports should not have bridge FDB entries on them.

We let drivers manage fast ageing under this condition because if DSA
were to do it, it would need to track each port's learning state, and
act upon the transition, which it currently doesn't.

But there are 2 reasons why doing it is better after all:

- drivers might get it wrong and not do it (see b53_port_set_learning)

- we would like to flush the dynamic entries from the software bridge
  too, and letting drivers do that would be another pain point

So track the port learning state and trigger a fast age process
automatically within DSA.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      045c45d1
  7. 06 8月, 2021 1 次提交
    • V
      net: dsa: don't disable multicast flooding to the CPU even without an IGMP querier · c73c5708
      由 Vladimir Oltean 提交于 
      Commit 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).

And commit a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.

The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:

- ICMP6 neighbor solicitation messages are unregistered multicast
  packets as far as the bridge is concerned. So if we stop flooding
  multicast, the outside world cannot ping the bridge device's IPv6
  link-local address.

- There might be foreign interfaces bridged with our DSA switch ports
  (sending a packet towards the host does not necessarily equal
  termination, but maybe software forwarding). So if there is no one
  interested in that multicast traffic in the local network stack, that
  doesn't mean nobody is.

- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
  the bridge is concerned. This should reach the CPU port.

- The switch driver might not do FDB partitioning. And since we don't
  even bother to do more fine-grained flood disabling (such as "disable
  flooding _from_port_N_ towards the CPU port" as opposed to "disable
  flooding _from_any_port_ towards the CPU port"), this breaks standalone
  ports, or even multiple bridges where one has an IGMP querier and one
  doesn't.

Reverting the logic makes all of the above work.

Fixes: a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c73c5708
  9. 24 7月, 2021 1 次提交
  11. 23 7月, 2021 1 次提交
    • V
      net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT · ce5df689
      由 Vladimir Oltean 提交于 
      The mv88e6xxx switches have the ability to receive FORWARD (data plane)
frames from the CPU port and route them according to the FDB. We can use
this to offload the forwarding process of packets sent by the software
bridge.

Because DSA supports bridge domain isolation between user ports, just
sending FORWARD frames is not enough, as they might leak the intended
broadcast domain of the bridge on behalf of which the packets are sent.

It should be noted that FORWARD frames are also (and typically) used to
forward data plane packets on DSA links in cross-chip topologies. The
FORWARD frame header contains the source port and switch ID, and
switches receiving this frame header forward the packet according to
their cross-chip port-based VLAN table (PVT).

To address the bridging domain isolation in the context of offloading
the forwarding on TX, the idea is that we can reuse the parts of the PVT
that don't have any physical switch mapped to them, one entry for each
software bridge. The switches will therefore think that behind their
upstream port lie many switches, all in fact backed up by software
bridges through tag_dsa.c, which constructs FORWARD packets with the
right switch ID corresponding to each bridge.

The mapping we use is absolutely trivial: DSA gives us a unique bridge
number, and we add the number of the physical switches in the DSA switch
tree to that, to obtain a unique virtual bridge device number to use in
the PVT.
Co-developed-by: NTobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: NTobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ce5df689
  13. 02 7月, 2021 6 次提交
  15. 22 6月, 2021 1 次提交
    • E
      net: dsa: mv88e6xxx: Fix adding vlan 0 · b8b79c41
      由 Eldar Gasanov 提交于 
      8021q module adds vlan 0 to all interfaces when it starts.
When 8021q module is loaded it isn't possible to create bond
with mv88e6xxx interfaces, bonding module dipslay error
"Couldn't add bond vlan ids", because it tries to add vlan 0
to slave interfaces.

There is unexpected behavior in the switch. When a PVID
is assigned to a port the switch changes VID to PVID
in ingress frames with VID 0 on the port. Expected
that the switch doesn't assign PVID to tagged frames
with VID 0. But there isn't a way to change this behavior
in the switch.

Fixes: 57e661aa ("net: dsa: mv88e6xxx: Link aggregation support")
Signed-off-by: NEldar Gasanov <eldargasanov2@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b8b79c41
  17. 22 4月, 2021 1 次提交
  19. 21 4月, 2021 3 次提交
  21. 13 4月, 2021 1 次提交
    • P
      net: phy: marvell: fix detection of PHY on Topaz switches · 1fe976d3
      由 Pali Rohár 提交于 
      Since commit fee2d546 ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.

This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.

This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.

Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.

Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.

Prior this change Topaz's internal PHY is detected by kernel as:

  PHY [...] driver [Marvell 88E6390] (irq=63)

And afterwards as:

  PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: NPali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546 ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: NMarek Behún <kabel@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1fe976d3
  23. 19 3月, 2021 7 次提交
  25. 18 3月, 2021 4 次提交
  27. 15 2月, 2021 2 次提交
  29. 13 2月, 2021 1 次提交
    • V
      net: dsa: act as passthrough for bridge port flags · a8b659e7
      由 Vladimir Oltean 提交于 
      There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.

One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.

Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.

Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it.  If it does, there
will need to be a dedicated .port_set_mrouter anyway.

So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.

The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:

behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)

so there was no reason to entangle them in the first place.

Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a8b659e7
  31. 02 2月, 2021 1 次提交
  33. 28 1月, 2021 1 次提交
  35. 27 1月, 2021 2 次提交
  37. 16 1月, 2021 2 次提交
    • V
      net: dsa: set configure_vlan_while_not_filtering to true by default · 0ee2af4e
      由 Vladimir Oltean 提交于 
      As explained in commit 54a0ed0d ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.

New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.

Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.

The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.

The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.

Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.

No behavior change except for the added prints is intended at this time.

$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[   60.315148] br0: port 1(sw0p2) entered blocking state
[   60.320350] br0: port 1(sw0p2) entered disabled state
[   60.327839] device sw0p2 entered promiscuous mode
[   60.334905] br0: port 1(sw0p2) entered blocking state
[   60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NKurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      0ee2af4e
    • T
      net: dsa: mv88e6xxx: Only allow LAG offload on supported hardware · b80dc51b
      由 Tobias Waldekranz 提交于 
      There are chips that do have Global 2 registers, and therefore trunk
mapping/mask tables are not available. Refuse the offload as early as
possible on those devices.

Fixes: 57e661aa ("net: dsa: mv88e6xxx: Link aggregation support")
Signed-off-by: NTobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      b80dc51b
  39. 15 1月, 2021 1 次提交