It doesn't seem like its needed. If this turns out to be an incorrect
assumption, we can reinstate it.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It was only used for bringup debugging, and probably doesn't work
anymore. Remove it.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Guest Memory Regions 2 is a way to bind pages to the GPU, but using
the FIFO instead of an io-submitted descriptor chain.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJosé Fonseca <jfonseca@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When GMR2 is available, make sure we restrict the number of used GMR pages
to the limit indicated by the device.
This is done by failing a GMRID allocation if the total number of GMR pages
exceeds the limit.
As a result TTM will then start evicting buffers in GMR memory on a
LRU basis until the allocation succeeds.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Previously this was not done when any 3D resource was active,
since that meant disabling the fifo with all 3D state lost.
Now, if there are still 3D resources active, we use the svga hide feature.

This fixes X server VT switching with 3D enabled.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Perform all command stream validation in a bounce buffer separate from the
fifo. This makes the fifo available to all validation-generated commands,
which would otherwise attempt to grab the fifo recursively, causing a
deadlock. This is in preparation for GMR2 and swappable surfaces.

Also maintain references to all surfaces in the command stream until the
command stream has been fired in order to avoid racing with surface
destruction taking place after validation but before submission.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The new DRM_RADEON_GEM_WAIT ioctl combines GEM_WAIT_IDLE and GEM_BUSY (there
is a NO_WAIT flag to get the latter) with USAGE_READ and USAGE_WRITE flags
to take advantage of the new ttm_bo_wait changes.

Also bump the DRM version.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Sometimes we want to know whether a buffer is busy and wait for it (bo_wait).
However, sometimes it would be more useful to be able to query whether
a buffer is busy and being either read or written, and wait until it's stopped
being either read or written. The point of this is to be able to avoid
unnecessary waiting, e.g. if a GPU has written something to a buffer and is now
reading that buffer, and a CPU wants to map that buffer for read, it needs to
only wait for the last write. If there were no write, there wouldn't be any
waiting needed.

This, or course, requires user space drivers to send read/write flags
with each relocation (like we have read/write domains in radeon, so we can
actually use those for something useful now).

Now how this patch works:

The read/write flags should passed to ttm_validate_buffer. TTM maintains
separate sync objects of the last read and write for each buffer, in addition
to the sync object of the last use of a buffer. ttm_bo_wait then operates
with one the sync objects.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRob Clark <rob@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRob Clark <rob@ti.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes resume on Compaq Presario V5245EU.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=41642Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

For some reason SPI block is in broken state after module
unloading. This lead to broken rendering after reloading
module. Fix this by reseting SPI block in CP resume function

Signed-off-by: Jerome Glisse <jglisse@redhat.com
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

It is left out the code to decrease the number of connector and encoder
to the cleanup functions.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
  i915: do not setup intel_backlight twice

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
  USB: ftdi_sio: add Calao reference board support
  USB option driver K3765/K4505 avoid CDC_DATA interface
  USB: option: add YUGA device id to driver
  usb: s5p-ehci: fix a NULL pointer deference
  USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
  USB option driver add PID of Huawei Vodafone K4605
  USB option driver add PID of Huawei Vodafone K3806
  xhci: Handle zero-length isochronous packets.
  USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
  usb: musb: gadget: fix error path
  usb: gadget: f_phonet: unlock in error case
  usb: musb: blackfin: include prefetch head file
  usb: musb: tusb6010: fix compilation
  usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
  usb: musb: cppi: fix build errors due to DBG and missing musb variable
  usb: musb: ux500: replace missing DBG with dev_dbg
  usb: musb: ux500: set dma config for both src and dst
  usb: musb: fix oops on musb_gadget_pullup
  usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
  usb: gadget: hid: don't STALL when processing a HID Descriptor request
  ...

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  omap-serial: Allow IXON and IXOFF to be disabled.
  TTY: serial, document ignoring of uart->ops->startup error
  TTY: pty, fix pty counting
  8250: Fix race condition in serial8250_backup_timeout().
  serial/8250_pci: delete duplicate data definition
  8250_pci: add support for Rosewill RC-305 4x serial port card
  tty: Add "spi:" prefix for spi modalias
  atmel_serial: fix atmel_default_console_device
  serial: 8250_pnp: add Intermec CV60 touchscreen device
  drivers/serial/ucc_uart.c: Fix compiler warning
  pch_uart: Set PCIe bus number using probe parameter
  serial: samsung: Fix build error

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  drivers:misc: ti-st: fix unexpected UART close
  drivers:misc: ti-st: free skb on firmware download
  drivers:misc: ti-st: wait for completion at fail
  drivers:misc: ti-st: reinit completion before send
  drivers:misc: ti-st: fail-safe on wrong pkt type
  drivers:misc: ti-st: reinit completion on ver read
  drivers:misc:ti-st: platform hooks for chip states
  drivers:misc: ti-st: avoid a misleading dbg msg
  base/devres.c: quiet sparse noise about context imbalance
  pti: add missing CONFIG_PCI dependency
  drivers/base/devtmpfs.c: correct annotation of `setup_done'
  driver core: fix kernel-doc warning in platform.c
  firmware: fix google/gsmi.c build warning

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: tidspbridge: fix compilation on dsp clock functions
  staging: octeon-ethernet: Add missing #includes.
  Staging: zcache: signedness bug in tmem_get()
  staging: zcache: fix crash on high memory swap
  staging: brcm80211: SPARC build error fix
  staging: brcm80211: fix compile error on non-x86 archs since 3.0 kernel

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] memory hotplug: only unassign assigned increments
  [S390] Change default action from reipl to stop for on_restart
  [S390] arch/s390/kernel/ipl.c: correct error detection check
  [S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
  [S390] nss,initrd: kernel image and initrd must be in different segments

According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.

Currently, we don't handle this special case and set irq field in
*_board_info structs to 255.  It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (32 commits)
  ALSA: hda: Conexant: Allow different output types to share DAC
  ASoC: Correct element count for WM8996 sidetone HPF
  ASoC: Tegra: wm8903 machine driver: Drop Ventana support
  ASoC: Add samsung maintainer
  ASoC: Add Springbank I/O card to Speyside Kconfig
  ALSA: hda/conexant - Enable ADC-switching for auto-mic mode, too
  ALSA: hda - Fix double-headphone/speaker paths for Cxt auto-parser
  ALSA: hda - Update jack-sense info even when no automute is set
  ALSA: hda - Fix output-path initialization for Realtek auto-parser
  sound/soc/fsl/mpc8610_hpcd.c: add missing of_node_put
  sound/soc/fsl/p1022_ds.c: add missing of_node_put
  sound/soc/ep93xx/ep93xx-i2s.c: add missing kfree
  sound/soc/kirkwood/kirkwood-i2s.c: add missing kfree
  ASoC: soc-core: use GFP_KERNEL flag for kmalloc in snd_soc_cnew
  sound/soc/fsl/fsl_dma.c: add missing of_node_put
  ASoC: Clear completions from late WM8996 FLL lock IRQs
  ASoC: Clear any outstanding WM8962 FLL lock completions before waiting
  ASoC: Ensure we only run Speyside WM8962 bias level callbacks once
  ASoC: Fix configuration of WM8996 input enables
  ASoC: WM8996 record paths need AIFCLK
  ...

This bug causes the IECSR register clear failure.  In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared.  So the related ISR may be called persistently.

The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The previous rtc-s3c had two issues related with its IRQ.

1. Users cannot open rtc multiple times because an open operation
   calls request_irq on the same IRQ.  (e.g., two user processes wants to
   open and read RTC time from rtc-s3c at the same time)

2. If alarm is set and no one has the rtc opened with filesystem
   (either the alarm is set by kernel/boot-loader or user set an alarm and
   closed rtc dev file), the pending bit is not cleared and no further
   interrupt is invoked.  When the alarm is used by the system itself such
   as a resume from suspend-to-RAM or other Low-power modes/idle, this is
   a critical issue.

This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC-S3C used to print out debug messages incorrectly.  This patch
corrects incorrect outputs.  (undecoded bcd numbers, incorrectly decoded
register values)

This patch affects the pr-debug messages only.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

bd2802_unregister_led_classdev() should unregister all registered
instances of led_classdev class that had registered by
bd2802_register_led_classdev().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NKim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following build errors:

  drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
  drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs

I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee ("platform: prefix MODALIAS with "platform:""), the
platform modalias is prefixed with "platform:".

This patch changes the MODULE_ALIAS to "platform:ab8500-pwm".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NArun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sure we are passing the same cookie in all calls to
request_threaded_irq() and free_irq().
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>