- 16 7月, 2013 7 次提交
-
-
由 David Spinadel 提交于
Increment index in each iteration. Without this increment we are overriding the added SSIDs and we will send only the last SSId and (n_ssids - 1) broadcast probes. Cc: <stable@vger.kernel.org> [3.9+] Signed-off-by: NDavid Spinadel <david.spinadel@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Due to a firmware bug, it crashes when the beacon interval is smaller than 16. Avoid this by refusing the station state change creating the AP station, causing mac80211 to abandon the attempt to connect to the AP, and eventually wpa_s to blacklist it. Cc: stable@vger.kernel.org Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
The firmware / HW can't support more than 16 Rx BA sessions. Deny any attemps to open more sessions than that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Emmanuel Grumbach 提交于
We didn't release the Rx AMPDU ressources properly. This bug led to firmware assert after 16 BA sessions. Cc: <stable@vger.kernel.org> [3.9+] Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Alexander Bondar 提交于
Avoid creating VIF specific debugfs directory if already exist. This may happen when, for example, resetting hw, suspend-resume. Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com> Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Johannes Berg 提交于
The BT_CONFIG command that is sent to the device during startup will enable BT coex unless the module parameter turns it off, but on devices without Bluetooth this may cause problems, as reported in Redhat BZ 885407. Fix this by sending the BT_CONFIG command only when the device has Bluetooth. Cc: stable@vger.kernel.org Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 Emmanuel Grumbach 提交于
This was missing and prevented any further attempts to load the module. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
-
- 15 7月, 2013 1 次提交
-
-
由 Linus Torvalds 提交于
-
- 13 7月, 2013 4 次提交
-
-
由 Neil Horman 提交于
this bug: https://bugzilla.redhat.com/show_bug.cgi?id=951695 Reported a dma debug backtrace: WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930() Hardware name: To Be Filled By O.E.M. via-rhine 0000:00:12.0: DMA-API: device driver failed to check map error[device address=0x0000000075a837b2] [size=90 bytes] [mapped as single] Modules linked in: ip6_tables gspca_spca561 gspca_main videodev media snd_hda_codec_realtek snd_hda_intel i2c_viapro snd_hda_codec snd_hwdep snd_seq ppdev mperf via_rhine coretemp snd_pcm mii microcode snd_page_alloc snd_timer snd_mpu401 snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore parport_pc parport shpchp ata_generic pata_acpi radeon i2c_algo_bit drm_kms_helper ttm drm pata_via sata_via i2c_core uinput Pid: 295, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.1.fc20.x86_64 #1 Call Trace: <IRQ> [<ffffffff81068dd0>] warn_slowpath_common+0x70/0xa0 [<ffffffff81068e4c>] warn_slowpath_fmt+0x4c/0x50 [<ffffffff8137ec6d>] check_unmap+0x47d/0x930 [<ffffffff810ace9f>] ? local_clock+0x5f/0x70 [<ffffffff8137f17f>] debug_dma_unmap_page+0x5f/0x70 [<ffffffffa0225edc>] ? rhine_ack_events.isra.14+0x3c/0x50 [via_rhine] [<ffffffffa02275f8>] rhine_napipoll+0x1d8/0xd80 [via_rhine] [<ffffffff815d3d51>] ? net_rx_action+0xa1/0x380 [<ffffffff815d3e22>] net_rx_action+0x172/0x380 [<ffffffff8107345f>] __do_softirq+0xff/0x400 [<ffffffff81073925>] irq_exit+0xb5/0xc0 [<ffffffff81724cd6>] do_IRQ+0x56/0xc0 [<ffffffff81719ff2>] common_interrupt+0x72/0x72 <EOI> [<ffffffff8170ff57>] ? __slab_alloc+0x4c2/0x526 [<ffffffff811992e0>] ? mmap_region+0x2b0/0x5a0 [<ffffffff810d5807>] ? __lock_is_held+0x57/0x80 [<ffffffff811992e0>] ? mmap_region+0x2b0/0x5a0 [<ffffffff811bf1bf>] kmem_cache_alloc+0x2df/0x360 [<ffffffff811992e0>] mmap_region+0x2b0/0x5a0 [<ffffffff811998e6>] do_mmap_pgoff+0x316/0x3d0 [<ffffffff81183ca0>] vm_mmap_pgoff+0x90/0xc0 [<ffffffff81197d6c>] sys_mmap_pgoff+0x4c/0x190 [<ffffffff81367d7e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff8101eb42>] sys_mmap+0x22/0x30 [<ffffffff81722fd9>] system_call_fastpath+0x16/0x1b Usual problem with the usual fix, add the appropriate calls to dma_mapping_error where appropriate Untested, as I don't have hardware, but its pretty straightforward Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> CC: David S. Miller <davem@davemloft.net> CC: Roger Luethi <rl@hellgate.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Horman 提交于
Recently had this backtrace reported: WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930() Hardware name: System Product Name ATL1E 0000:02:00.0: DMA-API: device driver failed to check map error[device address=0x00000000cbfd1000] [size=90 bytes] [mapped as single] Modules linked in: xt_conntrack nf_conntrack ebtable_filter ebtables ip6table_filter ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek iTCO_wdt iTCO_vendor_support snd_hda_intel acpi_cpufreq mperf coretemp btrfs zlib_deflate snd_hda_codec snd_hwdep microcode raid6_pq libcrc32c snd_seq usblp serio_raw xor snd_seq_device joydev snd_pcm snd_page_alloc snd_timer snd lpc_ich i2c_i801 soundcore mfd_core atl1e asus_atk0110 ata_generic pata_acpi radeon i2c_algo_bit drm_kms_helper ttm drm i2c_core pata_marvell uinput Pid: 314, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.3.fc19.x86_64 #1 Call Trace: <IRQ> [<ffffffff81069106>] warn_slowpath_common+0x66/0x80 [<ffffffff8106916c>] warn_slowpath_fmt+0x4c/0x50 [<ffffffff8138151d>] check_unmap+0x47d/0x930 [<ffffffff810ad048>] ? sched_clock_cpu+0xa8/0x100 [<ffffffff81381a2f>] debug_dma_unmap_page+0x5f/0x70 [<ffffffff8137ce30>] ? unmap_single+0x20/0x30 [<ffffffffa01569a1>] atl1e_intr+0x3a1/0x5b0 [atl1e] [<ffffffff810d53fd>] ? trace_hardirqs_off+0xd/0x10 [<ffffffff81119636>] handle_irq_event_percpu+0x56/0x390 [<ffffffff811199ad>] handle_irq_event+0x3d/0x60 [<ffffffff8111cb6a>] handle_fasteoi_irq+0x5a/0x100 [<ffffffff8101c36f>] handle_irq+0xbf/0x150 [<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50 [<ffffffff81073b10>] ? irq_enter+0x50/0xa0 [<ffffffff8172738d>] do_IRQ+0x4d/0xc0 [<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50 [<ffffffff8171c6b2>] common_interrupt+0x72/0x72 <EOI> [<ffffffff810db5b2>] ? lock_release+0xc2/0x310 [<ffffffff8109ea04>] lg_local_unlock_cpu+0x24/0x50 [<ffffffff811dcb2f>] file_sb_list_del+0x3f/0x50 [<ffffffff811dcb6d>] fput+0x2d/0xc0 [<ffffffff811d8ea1>] filp_close+0x61/0x90 [<ffffffff811fae4d>] __close_fd+0x8d/0x150 [<ffffffff811d8ef0>] sys_close+0x20/0x50 [<ffffffff81725699>] system_call_fastpath+0x16/0x1b The usual straighforward failure to check for dma_mapping_error after a map operation is completed. This patch should fix it, the reporter wandered off after filing this bz: https://bugzilla.redhat.com/show_bug.cgi?id=954170 and I don't have hardware to test, but the fix is pretty straightforward, so I figured I'd post it for review. Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
>> drivers/net/usb/r815x.c:38:16: sparse: cast to restricted __le32 >> drivers/net/usb/r815x.c:67:15: sparse: cast to restricted __le32 >> drivers/net/usb/r815x.c:69:13: sparse: incorrect type in assignment (different base types) drivers/net/usb/r815x.c:69:13: expected unsigned int [unsigned] [addressable] [assigned] [usertype] tmp drivers/net/usb/r815x.c:69:13: got restricted __le32 [usertype] <noident> Signed-off-by: NHayes Wang <hayeswang@realtek.com> Spotted-by: Nkbuild test robot <fengguang.wu@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
config: make ARCH=avr32 allyesconfig drivers/net/usb/r8152.c: In function 'rtl8152_start_xmit': drivers/net/usb/r8152.c:956: warning: integer overflow in expression 955 memset(tx_desc, 0, sizeof(*tx_desc)); > 956 tx_desc->opts1 = cpu_to_le32((len & TX_LEN_MASK) | TX_FS | TX_LS); 957 tp->tx_skb = skb; Signed-off-by: NHayes Wang <hayeswang@realtek.com> Spotted-by: Nkbuild test robot <fengguang.wu@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 7月, 2013 28 次提交
-
-
由 Wolfram Sang 提交于
Since commit ab78029e (drivers/pinctrl: grab default handles from device core), we can rely on device core for setting the default pins. Compile tested only. Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: NWolfram Sang <wsa@the-dreams.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wolfram Sang 提交于
Since commit ab78029e (drivers/pinctrl: grab default handles from device core), we can rely on device core for setting the default pins. Compile tested only. Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: NWolfram Sang <wsa@the-dreams.de> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wolfram Sang 提交于
Since commit ab78029e (drivers/pinctrl: grab default handles from device core), we can rely on device core for setting the default pins. Compile tested only. Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: NWolfram Sang <wsa@the-dreams.de> Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
Base on cdc_ether, add the mii functions for RTL8152 and RTL8153. The RTL8152 and RTL8153 support ECM mode which use the driver of cdc_ether. Add the mii functions. Then, the basic PHY access is possible. Signed-off-by: NHayes Wang <hayeswang@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
For copy_to/from_user() failure, the correct error code is -EFAULT not -EPERM. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Dean Luick 提交于
This patch adds code to log SDMA errors for supportability purposes. Signed-off-by: NDean Luick <dean.luick@intel.com> Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Mike Marciniszyn 提交于
The vzalloc()'ed field physshadow is leaked on module unload. This patch adds vfree after the sibling page shadow is freed. Reported-by: NDean Luick <dean.luick@intel.com> Reviewed-by: NDean Luick <dean.luick@intel.com> Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Moshe Lazer 提交于
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz. Fix the declaration of this field to be __be16 (which is what is in the firmware spec), renaming the field to log_uar_pg_size to conform to the spec, which fixes the endianness bug reported by sparse. Reported-by: NFengguang Wu <fengguang.wu@intel.com> Signed-off-by: NMoshe Lazer <moshel@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Bart Van Assche 提交于
If the transport layer is offline it is more appropriate to let srp_abort() return FAST_IO_FAIL instead of SUCCESS. Reported-by: NSebastian Riemer <sebastian.riemer@profitbricks.com> Acked-by: NDavid Dillow <dillowda@ornl.gov> Signed-off-by: NBart Van Assche <bvanassche@acm.org> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Mingarelli, Thomas 提交于
This patch is being created to use the UEFI bits in the type 219 SMBIOS record in order to decide whether or not to execute BIOS code. This is a better solution than to depend on the iCRU bit since not all future servers will use iCRU. Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be> ---- drivers/watchdog/hpwdt.c | 9 ++++++--- 1 files changed, 6 insertions(+), 3 deletions(-)
-
由 Kim, Milo 提交于
In watchdog_ping(), 'start' is called automatically when 'ping' function call is not configured. Softdog driver has same handling in both cases - start and ping, so 'ping' OPS can be removed. Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Johannes Thumshirn 提交于
This patch adds the driver for the watchdog devices found on MEN Mikro Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the watchdog framework. Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@men.de> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Russell King 提交于
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to clear. If we read the register, mask off the watchdog bit, and write it back, we're actually clearing every interrupt which wasn't pending at the time we read the register - and that is racy. Fix this to only write ~WATCHDOG_BIT to the register, which means we write as zero only the watchdog bit. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Acked-by: NJason Cooper <jason@lakedaemon.net> Tested-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Russell King 提交于
The watchdog infrastructure in Dove is no different from that in Orion5x or Kirkwood, so let's enable it for Dove. The only things missing are a few register settings in Dove's bridge-regs.h. Rather than duplicating the same register bit masks for the RSTOUTn_MASK and BRIDGE_CAUSE registers, move the definitions into the watchdog driver itself. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk> Acked-by: NJason Cooper <jason@lakedaemon.net> Tested-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Lubomir Rintel 提交于
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC, used in Raspberry Pi and Roku 2 devices. Signed-off-by: NLubomir Rintel <lkundrak@v3.sk> Tested-by: NStephen Warren <swarren@wwwdotorg.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be> Cc: linux-rpi-kernel@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree-discuss@lists.ozlabs.org
-
由 Viresh Kumar 提交于
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu interrupt (usually interrupt #30), and the GIC configuration should flag it as such. With this setup, request_irq() should fail, and the right API is request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq(). Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the right CPU. There are no users of this driver since a long time and it makes more sense to get rid of it as nobody is looking to fix it. In case somebody wakes up after this has been removed and needs it, please revert this driver and pick these updates (These were never pushed to mainline): http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org> Acked-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Michal Simek 提交于
Watchdog 1.01.a is also compatible with 1.00.a. Add the origin version to compatible list. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Michal Simek 提交于
- Remove reference for IP version - Fix header coding style - Remove notes which are visible from the code - Fix driver license according to header Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Andy Shevchenko 提交于
Kernel has nice helpers to dump buffers. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Hector Palacios 提交于
A watchdog device may be stopped from userspace using WDIOC_SETOPTIONS ioctl and flag WDIOS_DISABLECARD. If the device is closed after this operation, watchdog_release() is called and status bits checked for stopping it. Besides, if the device has not been unregistered a critical message "watchdog did not stop!" is printed, although the ioctl may have successfully stopped it already. Without the patch a user application sample code like this will successfully stop the watchdog, but the kernel will output the message "watchdog did not stop!": wd_fd = open("/dev/watchdog", O_RDWR); flags = WDIOS_DISABLECARD; ioctl(wd_fd, WDIOC_SETOPTIONS, &flags); close(wd_fd); Signed-off-by: NHector Palacios <hector.palacios@digi.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Lars-Peter Clausen 提交于
In preparation to switching the jz4740 clk driver to the common clk framework make sure to pass the device to clk_get(). Signed-off-by: NLars-Peter Clausen <lars@metafoo.de> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Sachin Kamat 提交于
Commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Sachin Kamat 提交于
Commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jingoo Han 提交于
Use the wrapper functions for getting and setting the driver data using platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev, so we can directly pass a struct platform_device. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jingoo Han 提交于
Use the wrapper functions for getting and setting the driver data using platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev, so we can directly pass a struct platform_device. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jingoo Han 提交于
Use the wrapper functions for getting and setting the driver data using platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev, so we can directly pass a struct platform_device. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jingoo Han 提交于
Instead of using legacy suspend/resume methods, using newer dev_pm_ops structure allows better control over power management. Signed-off-by: NJingoo Han <jg1.han@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jingoo Han 提交于
dev_err()/dev_info() are more preferred than pr_err()/pr_info(). Signed-off-by: NJingoo Han <jg1.han@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-