Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.

Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.

Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.

The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.

Contrary to what is hinted at in commit message of commit 15bfe05c
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support initialization with platdata, so the driver can be used on
non-device-tree platforms.

For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a side effect, a few error cases are fixed.

If of_iomap() of sdma_regs failed, no error code was returned.  Fixed to
return -ENOMEM similar to of_iomap() fail of regs.

If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.

Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: NEsben Haabendal <esben@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.

This issue was detected with the help of Coccinelle.

Fixes: 83a8471b ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vinicius Costa Gomes says:

====================
net/sched: taprio change schedules

Changes from RFC:
 - Removed the patches for taprio offloading, because of the lack of
   in-tree users;
 - Updated the links to point to the PATCH version of this series;

Original cover letter:

Overview
--------

This RFC has two objectives, it adds support for changing the running
schedules during "runtime", explained in more detail later, and
proposes an interface between taprio and the drivers for hardware
offloading.

These two different features are presented together so it's clear what
the "final state" would look like. But after the RFC stage, they can
be proposed (and reviewed) separately.

Changing the schedules without disrupting traffic is important for
handling dynamic use cases, for example, when streams are
added/removed and when the network configuration changes.

Hardware offloading support allows schedules to be more precise and
have lower resource usage.

Changing schedules
------------------

The same as the other interfaces we proposed, we try to use the same
concepts as the IEEE 802.1Q-2018 specification. So, for changing
schedules, there are an "oper" (operational) and an "admin" schedule.
The "admin" schedule is mutable and not in use, the "oper" schedule is
immutable and is in use.

That is, when the user first adds an schedule it is in the "admin"
state, and it becomes "oper" when its base-time (basically when it
starts) is reached.

What this means is that now it's possible to create taprio with a schedule:

$ tc qdisc add dev IFACE parent root handle 100 taprio \
      num_tc 3 \
      map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
      queues 1@0 1@1 2@2 \
      base-time 10000000 \
      sched-entry S 03 300000 \
      sched-entry S 02 300000 \
      sched-entry S 06 400000 \
      clockid CLOCK_TAI

And then, later, after the previous schedule is "promoted" to "oper",
add a new ("admin") schedule to be used some time later:

$ tc qdisc change dev IFACE parent root handle 100 taprio \
      base-time 1553121866000000000 \
      sched-entry S 02 500000 \
      sched-entry S 0f 400000 \
      clockid CLOCK_TAI

When enabling the ability to change schedules, it makes sense to add
two more defined knobs to schedules: "cycle-time" allows to truncate a
cycle to some value, so it repeats after a well-defined value;
"cycle-time-extension" controls how much an entry can be extended if
it's the last one before the change of schedules, the reason is to
avoid a very small cycle when transitioning from a schedule to
another.

With these, taprio in the software mode should provide a fairly
complete implementation of what's defined in the Enhancements for
Scheduled Traffic parts of the specification.

Hardware offload
----------------

Some workloads require better guarantees from their schedules than
what's provided by the software implementation. This series proposes
an interface for configuring schedules into compatible network
controllers.

This part is proposed together with the support for changing
schedules, because it raises questions like, should the "qdisc" side
be responsible of providing visibility into the schedules or should it
be the driver?

In this proposal, the driver is called passing the new schedule as
soon as it is validated, and the "core" qdisc takes care of displaying
(".dump()") the correct schedules at all times. It means that some
logic would need to be duplicated in the driver, if the hardware
doesn't have support for multiple schedules. But as taprio doesn't
have enough information about the underlying controller to know how
much in advance a schedule needs to be informed to the hardware, it
feels like a fair compromise.

The hardware offloading part of this proposal also tries to define an
interface for frame-preemption and how it interacts with the
scheduling of traffic, see Section 8.6.8.4 of IEEE 802.1Q-2018 for
more information.

One important difference between the qdisc interface and the
qdisc-driver interface, is that the "gate mask" on the qdisc side
references traffic classes, that is bit 0 of the gate mask means
Traffic Class 0, and in the driver interface, it specifies the queues,
that is bit 0 means queue 0. That is to say that taprio converts the
references to traffic classes to references to queues before sending
the offloading request to the driver.

Request for help
----------------

I would like that interested driver maintainers could take a look at
the proposed interface and see if it's going to be too awkward for any
particular device. Also, pointers to available documentation would be
appreciated. The idea here is to start a discussion so we can have an
interface that would work for multiple vendors.

Links
-----

kernel patches:
https://github.com/vcgomes/net-next/tree/taprio-add-support-for-change-v3

iproute2 patches:
https://github.com/vcgomes/iproute2/tree/taprio-add-support-for-change-v3
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.1Q-2018 defines the concept of a cycle-time-extension, so the
last entry of a schedule before the start of a new schedule can be
extended, so "too-short" entries can be avoided.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.1Q-2018 defines that a the cycle-time of a schedule may be
overridden, so the schedule is truncated to a determined "width".
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEEE 802.1Q-2018 defines two "types" of schedules, the "Oper" (from
operational?) and "Admin" ones. Up until now, 'taprio' only had
support for the "Oper" one, added when the qdisc is created. This adds
support for the "Admin" one, which allows the .change() operation to
be supported.

Just for clarification, some quick (and dirty) definitions, the "Oper"
schedule is the currently (as in this instant) running one, and it's
read-only. The "Admin" one is the one that the system configurator has
installed, it can be changed, and it will be "promoted" to "Oper" when
it's 'base-time' is reached.

The idea behing this patch is that calling something like the below,
(after taprio is already configured with an initial schedule):

$ tc qdisc change taprio dev IFACE parent root 	     \
     	   base-time X 	     	   	       	     \
     	   sched-entry <CMD> <GATES> <INTERVAL>	     \
	   ...

Will cause a new admin schedule to be created and programmed to be
"promoted" to "Oper" at instant X. If an "Admin" schedule already
exists, it will be overwritten with the new parameters.

Up until now, there was some code that was added to ease the support
of changing a single entry of a schedule, but was ultimately unused.
Now, that we have support for "change" with more well thought
semantics, updating a single entry seems to be less useful.

So we remove what is in practice dead code, and return a "not
supported" error if the user tries to use it. If changing a single
entry would make the user's life easier we may ressurrect this idea,
but at this point, removing it simplifies the code.

For now, only the schedule specific bits are allowed to be added for a
new schedule, that means that 'clockid', 'num_tc', 'map' and 'queues'
cannot be modified.

Example:

$ tc qdisc change dev IFACE parent root handle 100 taprio \
      base-time $BASE_TIME \
      sched-entry S 00 500000 \
      sched-entry S 0f 500000 \
      clockid CLOCK_TAI

The only change in the netlink API introduced by this change is the
introduction of an "admin" type in the response to a dump request,
that type allows userspace to separate the "oper" schedule from the
"admin" schedule. If userspace doesn't support the "admin" type, it
will only display the "oper" schedule.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now, this isn't a problem, but the next commit allows schedules
to be added during runtime. When a new schedule transitions from the
inactive to the active state ("admin" -> "oper") the previous one can
be freed, if it's freed just after the RCU read lock is released, we
may access an invalid entry.

So, we should take care to protect the dequeue() flow, so all the
places that access the entries are protected by the RCU read lock.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
undo congestion window on spurious SYN or SYNACK timeout

Linux TCP currently uses the initial congestion window of 1 packet
if multiple SYN or SYNACK timeouts per RFC6298. However such
timeouts are often spurious on wireless or cellular networks that
experience high delay variances (e.g. ramping up dormant radios or
local link retransmission). Another case is when the underlying
path is longer than the default SYN timeout (e.g. 1 second). In
these cases starting the transfer with a minimal congestion window
is detrimental to the performance for short flows.

One naive approach is to simply ignore SYN or SYNACK timeouts and
always use a larger or default initial window. This approach however
risks pouring gas to the fire when the network is already highly
congested. This is particularly true in data center where application
could start thousands to millions of connections over a single or
multiple hosts resulting in high SYN drops (e.g. incast).

This patch-set detects spurious SYN and SYNACK timeouts upon
completing the handshake via the widely-supported TCP timestamp
options. Upon such events the sender reverts to the default
initial window to start the data transfer so it gets best of both
worlds. This patch-set supports this feature for both active and
passive as well as Fast Open or regular connections.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Relocate the congestion window initialization from tcp_init_metrics()
to tcp_init_transfer() to improve code readability.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a helper to consolidate two identical code block for passive TFO.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes passive Fast Open reverts the cwnd to default
initial cwnd (10 packets) if the SYNACK timeout is spurious.

Passive Fast Open uses a full socket during handshake so it can
use the existing undo logic to detect spurious retransmission
by recording the first SYNACK timeout in key state variable
retrans_stamp. Upon receiving the ACK of the SYNACK, if the socket
has sent some data before the timeout, the spurious timeout
is detected by tcp_try_undo_recovery() in tcp_process_loss()
in tcp_ack().

But if the socket has not send any data yet, tcp_ack() does not
execute the undo code since no data is acknowledged. The fix is to
check such case explicitly after tcp_ack() during the ACK processing
in SYN_RECV state. In addition this is checked in FIN_WAIT_1 state
in case the server closes the socket before handshake completes.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP sender would use congestion window of 1 packet on the second SYN
and SYNACK timeout except passive TCP Fast Open. This makes passive
TFO too aggressive and unfair during congestion at handshake. This
patch fixes this issue so TCP (fast open or not, passive or active)
always conforms to the RFC6298.

Note that tcp_enter_loss() is called only once during recurring
timeouts.  This is because during handshake, high_seq and snd_una
are the same so tcp_enter_loss() would incorrect set the undo state
variables multiple times.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linux implements RFC6298 and use an initial congestion window
of 1 upon establishing the connection if the SYNACK packet is
retransmitted 2 or more times. In cellular networks SYNACK timeouts
are often spurious if the wireless radio was dormant or idle. Also
some network path is longer than the default SYNACK timeout. In
both cases falsely starting with a minimal cwnd are detrimental
to performance.

This patch avoids doing so when the final ACK's TCP timestamp
indicates the original SYNACK was delivered. It remembers the
original SYNACK timestamp when SYNACK timeout has occurred and
re-uses the function to detect spurious SYN timeout conveniently.

Note that a server may receives multiple SYNs from and immediately
retransmits SYNACKs without any SYNACK timeout. This often happens
on when the client SYNs have timed out due to wireless delay
above. In this case since the server will still use the default
initial congestion (e.g. 10) because tp->undo_marker is reset in
tcp_init_metrics(). This is an intentional design because packets
are not lost but delayed.

This patch only covers regular TCP passive open. Fast Open is
supported in the next patch.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detecting spurious SYNACK timeout using timestamp option requires
recording the exact SYNACK skb timestamp. Previously the SYNACK
sent timestamp was stamped slightly earlier before the skb
was transmitted. This patch uses the SYNACK skb transmission
timestamp directly.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linux implements RFC6298 and use an initial congestion window of 1
upon establishing the connection if the SYN packet is retransmitted 2
or more times. In cellular networks SYN timeouts are often spurious
if the wireless radio was dormant or idle. Also some network path
is longer than the default SYN timeout. Having a minimal cwnd on
both cases are detrimental to TCP startup performance.

This patch extends TCP undo feature (RFC3522 aka TCP Eifel) to detect
spurious SYN timeout via TCP timestamps. Since tp->retrans_stamp
records the initial SYN timestamp instead of first retransmission, we
have to implement a different undo code additionally. The detection
also must happen before tcp_ack() as retrans_stamp is reset when
SYN is acknowledged.

Note this patch covers both active regular and fast open.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously if an active TCP open has SYN timeout, it always undo the
cwnd upon receiving the SYNACK. This is because tcp_clean_rtx_queue
would reset tp->retrans_stamp when SYN is acked, which fools then
tcp_try_undo_loss and tcp_packet_delayed. Addressing this issue is
required to properly support undo for spurious SYN timeout.

Fixing this is tricky -- for active TCP open tp->retrans_stamp
records the time when the handshake starts, not the first
retransmission time as the name may suggest. The simplest fix is
for tcp_packet_delayed to ensure it is valid before comparing with
other timestamp.

One side effect of this change is active TCP Fast Open that incurred
SYN timeout. Upon receiving a SYN-ACK that only acknowledged
the SYN, it would immediately retransmit unacknowledged data in
tcp_ack() because the data is marked lost after SYN timeout. But
the retransmission would have an incorrect ack sequence number since
rcv_nxt has not been updated yet tcp_rcv_synsent_state_process(), the
retransmission needs to properly handed by tcp_rcv_fastopen_synack()
like before.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace "pass through" with a proper "fall through" annotation
in order to fix the following warning:

drivers/net/netdevsim/bus.c: In function ‘new_device_store’:
drivers/net/netdevsim/bus.c:170:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
   port_count = 1;
   ~~~~~~~~~~~^~~
drivers/net/netdevsim/bus.c:172:2: note: here
  case 2:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This fix is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
 # define unlikely(x) __builtin_expect(!!(x), 0)
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
  unlikely(__ret_warn_on);     \
  ^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
   WARN_ON(1);
   ^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
  case MC_CMD_FCNTL_OFF:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.

With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: atlantic: Aquantia driver updates 2019-04

This patchset contains various improvements:

- Work targeting link up speedups: link interrupt introduced, some other
  logic changes to imrove this.
- FW operations securing with mutex
- Counters and statistics logic improved by Dmitry
- read out of chip temperature via hwmon interface implemented by
  Yana and Nikita.

v4 changes:
- remove drvinfo_exit noop
- 64bit stats should be readed out sequentially (lsw, then msw)
  declare 64bit read ops for that

v3 changes:
- temp ops renamed to phy_temp ops
- mutex commits squashed for better structure

v2 changes:
- use threaded irq for link state handling
- rework hwmon via devm_hwmon_device_register_with_info
Extra comments on review from Andrew:
- direct device name pointer is used in hwmon registration.
  This causes hwmon device to derive possible interface name changes
- Will consider sanity checks for firmware mutex lock separately.
  Right now there is no single point exsists where such check could
  be easily added.
- There is no way now to fetch and configure min/max/crit temperatures
  via FW. Will investigate this separately.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).

Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Typo in msi code. No much impact though.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve for better readability
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we define and request an extra interrupt line,
assign it on link isr handler and restructure abit aq_pci code
to better support that.

We also remove logic for using different timer intervals
depending on link state, since thats now useless.
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need this to schedule link interrupt handling and
various service tasks.
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define link interrupt handler
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: NNikita Danilov <ndanilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for hwmon api to fetch out chip temperature
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to Neil who reported the issue leading to this
workaround, the workaround is no longer needed since
version 5.0. So let's remove it.

This was the bug report leading to the workaround:
https://bugzilla.kernel.org/show_bug.cgi?id=201081Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Tested-by: NNeil MacLeod <neil@nmacleod.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>