When ieee80211_hw.config indicates that the radio
is enabled and is configuring options that require
the link tuner to be restarted the link tuner will
cause a kernel panic when rfkill has indicated the
radio was in fact disabled.
Signed-off-by: NModestas Vainius <modestas@vainius.eu>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NModestas Vainius <modestas@vainius.eu>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As pointed out by Modestas Vainius the link tuner
could continue working while the radio is already
down. This because at the start of disable_radio
the ENABLED_RADIO flag is cleared and causes the
toggle_rx to skip the stop_link_tuner() call.
This will add a check to the start of the link tuner
which will automatically stop the link tuner when the
radio is disabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calling cancel_delayed_work_sync() unconditionally won't hurt
and it will avoid race conditions when another CPU is already
executing link_tuner work.
Signed-off-by: NModestas Vainius <modestas@vainius.eu>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Loosely based on the patch by Matthijs Kooijman,
this will add the dev_flags entry into debugfs which
will display rt2x00dev->flags.
This will allow easier debugging of flag handling.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2x00dev->flags has become a chaos over time,
this will reorganize the flags by renaming, deleting, adding
and properly implement the flags.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apparently rt2561s actually has PCI ID 0x0301
and rt2561 actually has PCI ID 0x0302.
Where rt2561s supports Turbo.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By increasing the timeout for rt2x00usb_vendor_request,
we should limit the number of loops required to send
a signal to the device succefully.
500ms timeout is specified by the Ralink legacy drivers
for rt2500usb. For rt73usb 1000ms is specified, but that
includes the timeout for the firmware which is already
specified in a different define.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make rt61pci_beacon_update and rt73usb_beacon_update static,
they are only used inside their own source file and then only
for setting it as callback funtion for mac80211.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to rt2x00lib_precalculate_link_signal resets link.rx_success
which is needed when calculating the average rssi for the link
tuner. Change the call order so the link tuner runs first as it
doesn't need the result of the precalculate.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The typedef is not required, we can just use "enum ieee80211_key_alg"
instead of "ieee80211_key_alg"
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.

This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.

Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.

At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().

The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.

Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Loopback device is special. It should be initialized at the very
beginning.  Initialization order has been changed by
Eric W. Biederman <ebiederm@xmission.com> and this change is non-obvious
and important enough to add proper comment.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids user confusion when they see that their device is not detected.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/pasemi_mac.c: At top level:
drivers/net/pasemi_mac.c:89: warning: 'read_iob_reg' defined but not used
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/spider_net_ethtool.c: In function 'spider_net_get_ethtool_stats':
drivers/net/spider_net_ethtool.c:160: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:161: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:162: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:163: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:164: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:165: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:166: error: structure has no member named 'netdev_stats'
make[2]: *** [drivers/net/spider_net_ethtool.o] Error 1

Also do another ARRAY_SIZE() cleanup while at it.
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It talks about __get_cpu_var() which the driver no longer
does.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes loopback_dev per network namespace.  Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.

This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working.  A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support for dynamically allocating the statistics counters
for the loopback device and adds appropriate device methods for allocating
and freeing the loopback device.

This completes support for creating multiple instances of the loopback
device,  in preparation for creating per network namespace instances.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixing memory alignment problems on the blackfin architecture (maybe on the
ARM also)
Signed-off-by: NVladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reserve two bytes to align pointer to the IP header.
Signed-off-by: NVladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch fixes the tx transmit timeout problem, which is
caused by the interrupts being incorrectly check and masked. The patch
moves the interrupt masking code so that interrupts are enabled only
when the driver is registered and only disabled when the driver is
unregistered.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Corrects a minor bug with priv->dnld_sent being set incorrectly in
if_cs_host_to_card.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change cleans up the radio-related messages in several ways.

(1) The state of the rfkill switch is assumed to be on, rather than
    tested. Now, any user without such a switch will not see any
    messages. For devices with such a switch, a message will be
    logged only if the initial state is off, or if the switch is toggled.
(2) The routine for testing the switch state is no longer inline.
(3) The LED handling routine is simplified.
(4) The "Radio turned off" message that has confused some users has been
    changed to "Radio initialized".

This patch is patterned after a similar change to b43 by Michael Buesch.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.

This patch is based on a similar patch of b43 by Michael Buesch.
Signed-off-by: NLarry Finger <larry.finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.

Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This message is useless. Only report state changes.

Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also cleanup the code a bit and remove the inline.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not required and the txpower adjustment must not be in atomic.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reinhard Speyerer reported at 2007-08-10 a new device.

Here are the information strings.

Product: Telegent TG54USB WLAN Adapter
USB ID: 129b:1666
Chip ID: zd1211 chip 129b:1666 v4330 high 00-01-36 RF2959_RF pa0 -----
FCC ID: N89-UW620Z
Signed-off-by: NUlrich Kunitz <kune@deine-taler.de>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some distros ship bcm43xx with debugging printout disabled. For those
BCM43xx devices with radio on/off switches, this makes it impossible
to know if the radio is on or off. This patch changes a pair of debug
printk's into ordinary printk's. It also changes the message that
prints when the radio is initialized to the off state as the old message
seems to confuse users.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to initialize to NULL when variable is never used before
it's assigned the return value of a kmalloc() call.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Doing this makes loopback.c a better example of how to do a
simple network device, and it removes the special case
single static allocation of a struct net_device, hopefully
making maintenance easier.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: NKirill Korotaev <dev@sw.ru>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>

This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: NKirill Korotaev <dev@sw.ru>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The remaining warning in phy.c will be fixed later.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>