Testing shows that the Domex 3191D card never asserts its IRQ. Hence it is
non-functional with Linux (worse, the EH bugs in the core driver are fatal
but that's a problem for another patch). Perhaps the DT-536 chip needs
special setup? I can't find documentation for it. The NetBSD driver uses
polling apparently because of this issue.

Set host->irq = NO_IRQ so the core driver will prevent targets from
disconnecting. Don't request host->irq.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h".
The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting
the other core drivers reduces the diff which makes them easier to unify.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The *_RELEASE macros don't tell me anything. In some cases the version in
the macro contradicts the version in the comments. Anyway, the Linux kernel
version is sufficient information. Remove these macros to improve readability.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Compile-time override of scsi host defaults is pointless for drivers that
provide module parameters and __setup options for that. Too many macros make
the code hard to read so remove them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Static variables from dtc.c and pas16.c should not appear in the core
NCR5380.c driver. Aside from being a layering issue this worsens the
divergence between the three core driver variants (atari_NCR5380.c and
sun3_NCR5380.c don't support PSEUDO_DMA) and it can mean multiple hosts
share the same counters.

Fix this by making the pseudo DMA spin counters in the core more generic.
This also avoids the abuse of the {DTC,PAS16}_PUBLIC_RELEASE macros, so
they can be removed.

oak.c doesn't use PDMA and hence it doesn't use the counters and hence it
needs no write_info() method. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If the host->info() method is not set, then host->name is used by default.
For atari_scsi, that is exactly the same text. So remove the redundant
info() method. Keep sun3_scsi.c in line with atari_scsi.

Some NCR5380 drivers return an empty string from the info() method
(arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default
(dmx3191d dtc.c g_NCR5380.c pas16.c t128.c).

Implement a common info() method to replace a lot of duplicated code which
the various drivers use to announce the same information.

This replaces most of the (deprecated) show_info() output and all of the
NCR5380_print_info() output. This also eliminates a bunch of code in
g_NCR5380 which just duplicates functionality in the core driver.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The NCR5380_STATS option is only enabled by g_NCR5380 yet it adds
clutter to all three core drivers. The atari_NCR5380.c and sun3_NCR5380.c
core drivers have a slightly different implementation of the
NCR5380_STATS option.

Out of all ten NCR5380 drivers, only one of them (g_NCR5380) actually
has the code to report on the collected stats. Aside from being unreadable,
that code seems to be broken because there's no initialization of timebase.
sun3_NCR5380.c and atari_NCR5380.c have the timebase initialization but
lack the code to report the stats.

Remove all of this code to improve readability and reduce divergence
between the three core drivers.

This patch and the next one completely eliminate the PRINTP and ANDP
pre-processor abuse.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Oak scsi doesn't use any IRQ, but it sets irq = IRQ_NONE rather than
SCSI_IRQ_NONE. Problem is, the core NCR5380 driver expects SCSI_IRQ_NONE
if it is to issue IDENTIFY commands that prevent target disconnection.
And, as Geert points out, IRQ_NONE is part of enum irqreturn.

Other drivers, when they can't get an IRQ or can't use one, will set
host->irq = SCSI_IRQ_NONE (that is, 255). But when they exit they will
attempt to free IRQ 255 which was never requested.

Fix these bugs by using NO_IRQ in place of SCSI_IRQ_NONE and IRQ_NONE.
That means IRQ 0 is no longer probed by ISA drivers but I don't think
this matters.

Setting IRQ = 255 for these ISA drivers is understood to mean no IRQ.
This remains supported so as to avoid breaking existing ISA setups (which
can be difficult to get working) and because existing documentation
(SANE, TLDP etc) describes this usage for the ISA NCR5380 driver options.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The LIMIT_TRANSFERSIZE, PSEUDO_DMA, PARITY and UNSAFE options are all
documented in the core drivers where they are used. The same goes for the
chip databook reference. Remove the duplicate comments.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Every NCR5380 driver sets AUTOSENSE so it need not be optional (and the
mid-layer expects it). Remove this redundant macro to improve readability.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Both atari_NCR5380.c and sun3_NCR5380.c core drivers #undef TAG_NONE and
then redefine it. But the original definition is unused because NCR5380.c
lacks support for tagged queueing. So just define it once.

The TAG_NEXT macro only appears in the arguments to NCR5380_select() calls.
But that routine doesn't use its tag argument as the tag was already
assigned in NCR5380_main(). So remove the unused argument and the macro.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make use of the host template static initializer instead of assigning
handlers at run-time. Move __maybe_unused qualifiers from declarations
to definitions. Move the atari_scsi_bus_reset() wrapper after the
definition of NCR5380_bus_reset(). All of the host template handler
prototypes are now redundant so remove them.

The write_info() handler is only relevant to drivers using PSEUDO_DMA so
this patch fixes the compiler warning in atari_NCR5380.c and sun3_NCR5380.c:

  CC      drivers/scsi/atari_scsi.o
  drivers/scsi/NCR5380.h:329: warning: 'NCR5380_write_info' declared 'static' but never defined
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add missing static qualifiers and remove the now pointless prototypes. The
NCR5380_* prototypes are all declared in NCR5380.h and renamed using macros.
Further declarations are redundant (some are completely unused). Remove
them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Some macros are never evaluated (i.e. FOO, USLEEP, SCSI2 and USE_WRAPPER;
and in some drivers, NCR5380_intr and NCR5380_proc_info). DRIVER_SETUP
serves no purpose anymore. Remove these macro definitions.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Some __setup() options mentioned in Documentation/scsi don't work because
a few lines of code went missing sometime since Linux 2.4. Fix the options
and thus fix some compiler warnings for both the non-modular case,

    CC      drivers/scsi/dtc.o
drivers/scsi/dtc.c:176:20: warning: 'dtc_setup' defined but not used [-Wunused-function]

and the modular case,

    CC [M]  drivers/scsi/pas16.o
drivers/scsi/pas16.c:335:20: warning: 'pas16_setup' defined but not used [-Wunused-function]
    CC [M]  drivers/scsi/t128.o
drivers/scsi/t128.c:147:20: warning: 't128_setup' defined but not used [-Wunused-function]
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Remove unused fields from hostdata structs declared with the
NCR5380_implementation_fields macro.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Having defined NDEBUG, and having set the console log level, I'd like to see
some output. Don't use pr_debug(), it's annoying to have to define DEBUG as
well.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When issuing I/O request, if the I/O completes before returning from
fnic_queuecommand(), we may be referencing scsi_cmnd structure that may
be freed by interrupt handler. Acquring IO lock would synchronize
fnic_queuecommand and interrupt handler.

- Increment fnic version from 1.6.0.15 to 1.6.0.16
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NAnil Chintalapati <achintal@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When physical link between standalone C series and switch is down,
the fip timer is not turned off and timer expiration will keep sending
vlan request.

It can be fixed by stopping the fip_timer and
it will be restarted automatically when Link is up.

- Increment fnic version from 1.6.0.14 to 1.6.0.15
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NAnil Chintalapati <achintal@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

IOs belonging to an rport are aborted with Internal terminate option
when rport goes offline. Any new IO issued to the rport during this
time can reuse the terminated exchange which will cause inconsistent
state of the exchange between local port and remote port.

fc_rport_priv is set to RPORT_ST_DELETE before exchanges are aborted by
libfc. Not issuing amy more I/O requests when RPORT_ST_DELETE is set,
will avoid inconsistent state of the exchange between local port and
remote port.

- Increment fnic version from 1.6.0.13 to 1.6.0.14
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NAnil Chintalapati <achintal@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In case of receive path, we do not have eth header or fcoe header available
when we take a trace so we fill the fc trace buffer with 0xff for both
values. We copy only mimimum of received data or trace buffer size -
fc header - eth and fcoe header

- Increment fnic version from 1.6.0.12 to 1.6.0.13
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NAnil Chintalapati <achintal@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In fnic_dev_wait, Wait for finish to complete at least three times in two
seconds while loop before returning -ETIMEDOUT as sometime
schedule_timeout_uninterruptible takes more than two seconds to wake up.

- Increment fnic version from 1.6.0.11 to 1.6.0.12
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NAnil Chintalapati <achintal@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We should be returning an error code here instead of success.  Either
-ENODEV or -ENOMEM would work.  There is also a failure message in
printk().
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The bnx2fc_if_create() function returns NULL on failure, it never
returns an error pointer.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

At least LID reassignment can trigger a race condition in the SRP
initiator driver, namely the receive completion handler trying to
post a request on a QP during or after QP destruction and before
the CQ's have been destroyed. Avoid this race by modifying a QP
into the error state and by waiting until all receive completions
have been processed before destroying a QP.
Reported-by: NMax Gurtuvoy <maxg@mellanox.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Improve performance by using multiple RDMA/RC channels per SCSI
host for communication with an SRP target. About the
implementation:
- Introduce a loop over all channels in the code that uses
  target->ch.
- Set the SRP_MULTICHAN_MULTI flag during login for the creation
  of the second and subsequent channels.
- RDMA completion vectors are chosen such that RDMA completion
  interrupts are handled by the CPU socket that submitted the I/O
  request. As one can see in this patch it has been assumed if a
  system contains n CPU sockets and m RDMA completion vectors
  have been assigned to an RDMA HCA that IRQ affinity has been
  configured such that completion vectors [i*m/n..(i+1)*m/n) are
  bound to CPU socket i with 0 <= i < n.
- Modify srp_free_ch_ib() and srp_free_req_data() such that it
  becomes safe to invoke these functions after the corresponding
  allocation function failed.
- Add a ch_count sysfs attribute per target port.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Since the block layer already contains functionality to assign
a tag to each request, use that functionality instead of
reimplementing that functionality in the SRP initiator driver.
This change makes the free_reqs list superfluous. Hence remove
that list.

[hch: updated to use .use_blk_tags instead scsi_activate_tcq]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Changes in this patch:
- Move channel variables into a new structure (struct srp_rdma_ch).
- Add an srp_target_port pointer, 'lock' and 'comp_vector' members
  in struct srp_rdma_ch.
- Add code to initialize these three new member variables.
- Many boring "target->" into "ch->" changes.
- The cm_id and completion handler context pointers are now of type
  srp_rdma_ch * instead of srp_target_port *.
- Three kzalloc(a * b, f) calls have been changed into kcalloc(a, b, f)
  to avoid that this patch would trigger a checkpatch warning.
- Two casts from u64 into unsigned long long have been left out
  because these are superfluous. Since considerable time u64 is
  defined as unsigned long long for all architectures supported by
  the Linux kernel.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Acked-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Introduce the srp_target_port member variables 'sgid' and 'pkey'.
Change the type of 'orig_dgid' from __be16[8] into union ib_gid.
This patch does not change any functionality but makes the
"Separate target and channel variables" patch easier to verify.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If a cable is pulled during LUN scanning it can happen that the
SRP rport and the SCSI host have been created but no LUNs have been
added to the SCSI host. Since multipathd only sends SCSI commands
to a SCSI target if one or more SCSI devices are present and since
there is no keepalive mechanism for IB queue pairs this means that
after a LUN scan failed and after a reconnect has succeeded no
data will be sent over the QP and hence that a subsequent cable
pull will not be detected. Avoid this by not creating an rport or
SCSI host if a cable is pulled during a SCSI LUN scan.

Note: so far the above behavior has only been observed with the
kernel module parameter ch_count set to a value >= 2.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Attempting to connect three times may be insufficient after an
initiator system tries to relogin, especially if the relogin
attempt occurs before the SRP target service ID has been
registered. Since the srp_daemon retries a failed login attempt
anyway, remove the stale connection retry mechanism.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The patch that adds multichannel support into the SRP initiator
driver introduces an additional call to srp_free_ch_ib(). This
patch helps to keep that later patch simple.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Remove 2 redundant extern inline functions: qla8044_set_qsnt_ready() and
qla8044_need_reset_handler(). At present, within upstream next kernel
source code, they are only used within "drivers/scsi/qla2xxx/qla_nx2.c".

The related error and warnings (with allmodconfig under tile):

    CC [M]  drivers/scsi/qla2xxx/qla_nx2.o
  drivers/scsi/qla2xxx/qla_nx2.c:1633:1: error: static declaration of 'qla8044_need_reset_handler' follows non-static declaration
   qla8044_need_reset_handler(struct scsi_qla_host *vha)
   ^
  In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
                   from drivers/scsi/qla2xxx/qla_nx2.c:11:
  drivers/scsi/qla2xxx/qla_gbl.h:756:20: note: previous declaration of 'qla8044_need_reset_handler' was here
   extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha);
                      ^
  drivers/scsi/qla2xxx/qla_gbl.h:756:20: warning: inline function 'qla8044_need_reset_handler' declared but never defined
  make[3]: *** [drivers/scsi/qla2xxx/qla_nx2.o] Error 1
  make[2]: *** [drivers/scsi/qla2xxx] Error 2
  make[1]: *** [drivers/scsi] Error 2
  make: *** [drivers] Error 2

    CC [M]  drivers/scsi/qla2xxx/qla_tmpl.o
  In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
                   from drivers/scsi/qla2xxx/qla_tmpl.c:7:
  drivers/scsi/qla2xxx/qla_gbl.h:755:20: warning: inline function 'qla8044_set_qsnt_ready' declared but never defined
   extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha);
                    ^
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Acked-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use dma_set_mask_and_coherent() to set both the DMA and coherent
DMA mask.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Even though the ipr driver is only used on PCI, convert it
to use the generic DMA API.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The request (and SCSI command) tag is the tag number assigned
by the generic block-tagging code, not the SCSI-II tag messages.
Those are represented by the device flags 'tagged_supported',
'simple_tags', and 'ordered_tags'.
(The SCSI midlayer doesn't use HEAD_OF_QUEUE tags).
So fixup vmw_pvscsi to assign the correct tag type.

[hch: fixed up to never set MSG_ORDERED_TAG]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NArvind Kumar <arvindkumar@vmware.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This macro is only used in the NCR5380 drivers and they don't include
this header.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

ufs never looks at the tag type, so there is no need to set it either.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Now that we also get proper values in cmd->request->tag for untagged
commands, there is no need to force tagged_supported to on in drivers
that need host-wide tags.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>