Support interrupt from device which indicates VF has placed
A request on the VF <-> PF channel.
The PF driver issues a DMAE to retrieve the request from the VM
memory (the Ghost Physical Address of the request is contained
in the interrupt. The PF driver uses the GPA in the DMAE request,
which is translated by the IOMMU to the correct physical address).
The request which arrives is examined to recognize the sending VF.
The PF driver allocates a workitem to handle the VF Operation (vfop).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At nic load of the PF, if VFs may be present, prepare the device
for the VFs. Initialize the VF database in preparation of VF arrival.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When A PF determines that it may have to manage SRIOV VFs it
allocates a database for this purpose. The database is intended to
keep track of the VF state, the resources allocated for each VF
(queues, interrupt vectors, etc), the state of the VF's queues.
When the VF loads the database is updated accordingly.
When A VF closes the database is consulted to determine which
resources need to be released (close queues against device, reclaim
interrupt vectors, etc).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VF driver is transmitting it must supply the correct mac
address in the parsing BD. This is used for firmware validation
and enforcement and also for tx-switching.
Refactor interrupt ack flow to allow for different BAR addresses of
the hardware in the PF BAR vs the VF BAR.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF driver uses the 'q_filter' request in the VF <-> PF channel to
have the PF configure the requested rxmode to device. ndo_set_rxmode
is called under bottom half lock, so sleeping until the response
arrives over the VF <-> PF channel is out of the question. For this reason
the VF driver returns from the ndo after scheduling a work item, which
in turn processes the rx mode request and adds the classification
information through the VF <-> PF channel accordingly.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF is being closed its queues are released via
the 'teardown_q' and the VF itself is closed with
'close'. These are essentially the unload counterparts of
'init' and 'setup_q' from the load flow.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'init' - init an acquired VF. Supply allocation GPAs to PF.
'setup_q' - PF to allocate a queue in device on behalf of the VF.
'set_mac' - PF to configure a mac in device on behalf of the VF.
VF driver uses these requests in the VF <-> PF channel in nic_load
flow.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generally, the VF driver cannot access the chip, except by the
narrow window its BAR allows. Care had to be taken so the VF driver
will not reach code which accesses the chip elsewhere.
Refactor the nic_load flow into parts so it would be
easier to separate the VF-only logic from the PF-only logic.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF driver uses this request when removed. The PF driver
reclaims all resources allocated for that VF at this
time.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the 'acquire' request to VF <-> PF channel and use it at
VF probe. In the acquire request the VF driver lists the resources
it would like to have. In the response the PF either ratifies the
request, or denies it and supplies the maximum values supported.
The VF may then attempt another acquire request.
This patch adds the bnx2x_vfpf.c file which contains the
implementation of the VF to PF hardware channel.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support probing and removing of a bnx2x virtual function
the following were added:
1. add bnx2x_vfpf.h: defines the VF to PF channel
2. add bnx2x_sriov.h: header for bnx2x SR-IOV functionality
3. enumerate VF hw types (identify VFs)
4. if driving a VF, map VF bar
5. if driving a VF, allocate Vf to PF channel
6. refactor interrupt flows to include VF
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use prandom_bytes() to fill rss key with pseudo-random bytes.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Laight <david.laight@aculab.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using netdev_alloc_frag() instead of kmalloc() permits better GRO or
TCP coalescing behavior, as skb_gro_receive() doesn't have to fallback
to frag_list overhead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible that the driver is configured to operate with a certain
link configuration which differs from the link's configuration during
boot from SAN - this would cause the driver to flap the link.

Said flap may be missed by specific switches, causing dcbx convergence
to be too long and boot sequence to fail. Convergence is longer because
switch ignores new dcbx packets due to counters mismatch, as only host
side reset the counters due to the link flap.

This patch causes the driver to ignore user's initial configuration during
boot from SAN, and continues with the existing link configuration.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using symbol_get(), cnic can now directly call the cnic_probe
functions in struct bnx2x and struct bnx2.  symbol_get() is not reliable
as it fails when the module is still initializing.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without the reset, reloading the cnic driver can cause the iSCSI
Event Queue to be out of sync with the driver and cause intermittent
crash.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If fan failure is detected, MCP prevents PCI I/O registers from being
mapped to the bar, causing a fatal error as driver is unaware.

This patch recognizes such an event occurred and gracefully terminates
the probe process.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x driver could only have enabled pfc via usage of dcbnl; now, it can
also correctly disable it.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring pauses using 'ethtool -A', the requested values have
effect when used together with autoneg (up to this point, when configured
for autoneg, driver ignored requested pause configuration)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A rare case of no link due to a missed interrupt may occur due to a
race condition between acknowledging the IGU via the BAR and restoring the NIG
interrupt mask via the GRC.
To solve it, we wait for the IGU ack command to finish prior to restoring the
NIG interrupt mask.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unmasked interrupt caused "FATAL HW block attention set2 0x20" messages
to erroneously appear, as the associated interrupt is fully recoverable.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If IGU parse error is encountered during the probing process, the error
propagates and the probe gracefully fails (until now, such errors were ignored,
later causing mischief).
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is now possible to enable dropless flow control via nvram.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If link is down due to management (and not due to actual phy link being lost),
driver should still behave as if the link is down; Querying via ethtool about
speed/duplex state should result in 'UNKNOWN' (same behaviour as when link is
actually down).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whenever bnx2x fails to transmit a packet due to a full Tx ring, if the
ring size is zero (indicating an FCoE ring) driver filters the packet out
and gracefully continues.
Driver also gathers statistics on such filtered packets.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If configured for PFC/ETS by management, configure chip regardless of the
presence of a remote peer which supports DCBX.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parity recovery was enhanced in order to handle a few more corner cases.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changed naming convention of SPIO macros, and prevented access to invalid SPIOs.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not a real problem, since the EEE is supported for devices where the
actual_phy_selection is zero, such that the req_duplex of params will match
the one of the phy struct.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The string was split to several lines since it reached over 180 chars, which
seems too much.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes some cosmetic changes to the code:
1. Code alignment.
2. Merge read-modify-write into a single function (read_or_write /
read_and_write).
3. Merge several write registers into a for-loop write using a static array.
4. Remove empty lines.
5. Fix comments.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.

Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per measurements, the SFP+ suffered from small current leakage in two cases:
 - When no module was plugged and TX laser was disabled. The fix was to enable
   it, and when module is plugged in, check if it needs to be disabled.
 - When over-current event occurs due to invalid SFP+ module, the HW basically
   shuts down the current for this module, but the SW needs to complete this
   by issuing a power down via a GPIO.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>