Add support for the CAN controller found in Renesas R-Car SoCs.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Non-TI chips (including socfpga) needs different raminit sequence. Implement
it.
Tested-by: NThor Thayer <tthayer@altera.com>
Signed-off-by: NThor Thayer <tthayer@altera.com>
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add helpers for 32-bit accesses and replace open-coded 32-bit access
with calls to helpers. Minimum changes are done to the pci case, as I
don't have access to that hardware.
Tested-by: NThor Thayer <tthayer@altera.com>
Signed-off-by: NThor Thayer <tthayer@altera.com>
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch makes the {read,write}_reg functions const, this is a preparation to
make use of {read,write}_reg in the hwinit callback.
Signed-off-by: NThor Thayer <tthayer@altera.com>
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The pch_can driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The only driver based on MSCAN at the moment is for PPC machines,
so it makes no sense to present the menu on M68K. The menu will always
be empty there.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The at91_can driver is AT91-specific so it should depend on ARCH_AT91
rather than just ARM. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

drivers/net/can/spi/mcp251x.c:953:7-27: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT

 Make sure threaded IRQs without a primary handler are always request with
 IRQF_ONESHOT

Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci

CC: Stefano Babic <sbabic@denx.de>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Included changes:
- fix codestyle to respect new checkpatch warnings
- increase internal version number

There is otherwise a risk of a possible null pointer dereference.

Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of raw math.
Signed-off-by: NManuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of raw math.
Signed-off-by: NManuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function mlx4_en_set_channels() stops running ports before performing the
requested action. In that case local variable 'port_up' is set so that the
port is restarted at the end of the function, however, in case the port was
not stopped, variable 'port_up' is left uninitialized and the behaviour is
undetermined. Detected by Coverity - CID 751497.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Acked-By: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix build when BRIDGE_VLAN_FILTERING is not set

Fixes: 2796d0c6 ("bridge: Automatically manage port promiscuous mode")
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Reported by checkpatch with the following warning:
"WARNING: macros should not use a trailing semicolon"
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Reported by checkpatch with the following message:
"WARNING: Missing a blank line after declarations"
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Bjørn Mork says:

====================
cdc_ncm: add buffer tuning and stats using ethtool

Quoting the previous description of this series (skip to the
changelog below if you only want a summary of the changes):

"I have got quite a few reports from frustrated users of OpenWRT
hosts trying to use some powerful LTE modem, but not achieving
full speed.  This is typically caused by a combination of
big buffers and little memory, giving in allocation errors and
bad performance as a result.

This series is an attempt to let users adjust the size of these
buffers without having to rebuild the driver.

Patches 1 - 4 are mostly rearranging existing code, in preparing
for the dynamic buffer size changes.

Patch 5 adds userspace control (ab)using the ethtool coalescing
API. This isn't a perfect match, which is the main reason why I
post this series as a RFC.

Patch 6 is an unrelated framing optimization, reducing the
overhead quite a bit and allowing for better use of smaller
buffers.

Patch 7 changes the way we calculate frame padding cutoff. The
problem with big buffers is made much worse by the current padding
strategy where zero padding often can account for more than 90% of
the frames.

Patch 8 add some counters giving some insight into how well the
NCM/MBIM protocol works, supporting further tuning.

Patch 9 reduce the initial maximum buffer size from 32kB to 16kB
in an attempt to make the default better suit all. It is still
possible to tune this up again to the old fixed max, using the
new tuning knobs.

I must admit that I had higher hopes for this series before I
tested it on my own modems.  One really unexpected result was
that one of the MBIM modems accepted the new rx buffer size we
set, but happily continued sending buffers of the same size as
before.  Needless to say:  This did not work very well...

So don't really expect to be able to use any values with any
given device. Firmware implementations are still... I don't
think I have words suitable for a public mailing list.

But I am hoping this will help the many users who have had success
rebuilding the driver with lower fixed limits.

Please test and/or comment!"

Changes:

** RFC -> v1 **

Patch 10 - a follow-up to a comment Joe Perches made in November
           2013.  I don't always forget :-)
Patch 11 - removes the redundant "connected" driver state, and the
           associated .check_connect callbacks.

** v1 -> v2 **

Patch 1  - Better handling of minium rx buffer size, based on feedback
           from Oliver Neukum and Enrico Mioso
Patch 5  - fixed locking around timer interval update
Patch 9  - fixed whitespace error
Patch 12 - new fix related to the tuneable tx timer

...and spelling fixes all over the commit messages.  I have finally
added a spelling hook, which I'm sure may of you will appreciate :-)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can end up with a freshly allocated tx_curr_skb with no frames
in it.  In this case it does not make any sense to start the timer.
This avoids the timer periodically trying to start tx when there
is nothing in the queue.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling netif_carrier_{on,off} is sufficient.  There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.

Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.

Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.

With very few exceptions, users are only interested in
the payload size.  Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.

Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.

X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link.  As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.

The current defaults are based on the assumption that device
side buffers should be the limiting factor.  However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing.  And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .

A start on improving this is going from build time hard
coded limits to per device user configurable limits.  The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Finish the rx_max/tx_max setup by flushing buffers and
informing usbnet about the changes.  This way, the settings
can be modified while the netdev is up and running.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have split out the part of the device setup
which MUST be done with the data interface in altsetting 0,
we can delay the rest of the initialization. This allows us
to move some of post-init buffer size config from bind to
the appropriate setup function.

The purpose of this refactoring is to collect all code
adjusting the rx_max and tx_max buffers in one place, so
that it is easier to call it from multiple call sites.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the parts of setup dealing with device initialization from
parts just setting defaults for attributes which might be
changed after initialization.

Some commands of the device initialization are only allowed when
the data interface is in its disabled altsetting, so we must
separate them out of we are to allow rerunning parts of setup.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split out the part of setup dealing with updating the rx_max
and tx_max buffer sizes so that this code can be reused for
dynamically updating the limits.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Phoebe Buckheister says:

====================
802154: implement link-layer security

This patch series implements 802.15.4-2011 link layer security.

Patches 1 and 2 prepare for llsec by adding data structures to represent the
llsec PIB as specified in 802.15.4-2011. I've changed some structures from
their specification to be more sensible, since 802.15.4 specifies some
structures in not-exactly-useful ways. Nested lists are common, but not very
accessible for netlink methods, and not very fast to traverse when searching
for specific elements either.

Patch 3 implements backends for these structures in mac802154.

Patch 4 and 5 implement the encryption and decryption methods, split from patch
3 to ease review. The encryption and decryption methods are almost entirely
compliant with the specified outgoing/incoming frame procedures. Decryption
deviates from the specification slightly where the specification makes no
sense, i.e. encrypted frames with security level 0 may be sent, but must be
dropped an reception - but transforms for processing such frames are given a
few lines in the standard. I've opted to not drop these frames instead of not
implementing the transforms that wouldn't be used if they were dropped.

Patch 6 links the mac802154 llsec with the SoftMAC devices. This is mainly
init//fini code for llsec context, handling of security subheaders and calling
the encryption/decryption methods.

Patch 7 adds sockopts to 802.15.4 dgram sockets to modifiy outgoing security
parameters on a per-socket basis. Ideally, this would also be available for
sockets on 6lowpan devices, but I'm not sure how to do that nicely.

Patch 8 adds forwarders to the llsec configuration methods for netlink, patch
10 implements these netlink accessors. This is mainly mechanical.

Patch 11, implements a key tracking option for devices that previous patches
haven't, because I'm not entirely sure whether this is the best approach to the
problem. It performs reasonably well though, so I decided to include it as a
separate patch in this series instead of sending an RFC just for this one
option.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 802.15.4-2011 standard states that for each key, a list of devices
that use this key shall be kept. Previous patches have only considered
two options:

 * a device "uses" (or may use) all keys, rendering the list useless
 * a device is restricted to a certain set of keys

Another option would be that a device *may* use all keys, but need not
do so, and we are interested in the actual set of keys the device uses.
Recording keys used by any given device may have a noticable performance
impact and might not be needed as often. The common case, in which a
device will not switch keys too often, should still perform well.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds user-visible interfaces for the llsec infrastructure.
For the added methods, the only major difference between all add/remove
implementation lies in how the specific object is parsed, and for dump
requests, how objects are written into netlink messages.

To save on boilerplate code, table dumps are routed through a helper
function that handles netlink dump state, leaving the actual dumping
code to care only about iterating over the table to be dumped and
filling netlink messages. For add/remove methods, the boilerplate
required to work is not quite as large, but still enough to also move
into a local helper.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow datagram sockets to override the security settings of the device
they send from on a per-socket basis. Requires CAP_NET_ADMIN or
CAP_NET_RAW, since raw sockets can send arbitrary packets anyway.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>