In the bio_for_each_segment loop, bvl always points current
bio_vec, so the same as bio_iovec_idx(, i). Let's get rid of
it.

Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Commit e9c7469b ("md: implment REQ_FLUSH/FUA support")
introduced R5_WantFUA flag and set rw to WRITE_FUA in that case.
However remaining code still checks whether rw is exactly same
as WRITE or not, so FUAed-write ends up with being treated as
READ. Fix it.

This bug has been present since 2.6.37 and the fix is suitable for any
-stable kernel since then.  It is not clear why this has not caused
more problems.

Cc: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

The @bio->bi_phys_segments consists of active stripes count in the
lower 16 bits and processed stripes count in the upper 16 bits. So
logical-OR operator should be bitwise one.

This bug has been present since 2.6.27 and the fix is suitable for any
-stable kernel since then.  Fortunately the bad code is only used on
error paths and is relatively unlikely to be hit.

Cc: stable@kernel.org
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Reported-by: NCoolCold <coolthecold@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Get rid of ->syncchunk and ->counter_bits since they're never used.

Also discard COUNTER_BYTE_RATIO which is unused.
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Use COUNTER()/NEEDED() macro instead of open-coding them.
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Check pers->hot_remove_disk instead of pers->hot_add_disk in slot_store()
during disk removal. The linear personality only has ->hot_add_disk and
no ->hot_remove_disk, so that removing disk in the array resulted to
following kernel bug:

$ sudo mdadm --create /dev/md0 --level=linear --raid-devices=4 /dev/loop[0-3]
$ echo none | sudo tee /sys/block/md0/md/dev-loop2/slot
 BUG: unable to handle kernel NULL pointer dereference at           (null)
 IP: [<          (null)>]           (null)
 PGD c9f5d067 PUD 8575a067 PMD 0
 Oops: 0010 [#1] SMP
 CPU 2
 Modules linked in: linear loop bridge stp llc kvm_intel kvm asus_atk0110 sr_mod cdrom sg

 Pid: 10450, comm: tee Not tainted 3.0.0-rc1-leonard+ #173 System manufacturer System Product Name/P5G41TD-M PRO
 RIP: 0010:[<0000000000000000>]  [<          (null)>]           (null)
 RSP: 0018:ffff880085757df0  EFLAGS: 00010282
 RAX: ffffffffa00168e0 RBX: ffff8800d1431800 RCX: 000000000000006e
 RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff88008543c000
 RBP: ffff880085757e48 R08: 0000000000000002 R09: 000000000000000a
 R10: 0000000000000000 R11: ffff88008543c2e0 R12: 00000000ffffffff
 R13: ffff8800b4641000 R14: 0000000000000005 R15: 0000000000000000
 FS:  00007fe8c9e05700(0000) GS:ffff88011fa00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000000 CR3: 00000000b4502000 CR4: 00000000000406e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 Process tee (pid: 10450, threadinfo ffff880085756000, task ffff8800c9f08000)
 Stack:
  ffffffff8138496a ffff8800b4641000 ffff88008543c268 0000000000000000
  ffff8800b4641000 ffff88008543c000 ffff8800d1431868 ffffffff81a78a90
  ffff8800b4641000 ffff88008543c000 ffff8800d1431800 ffff880085757e98
 Call Trace:
  [<ffffffff8138496a>] ? slot_store+0xaa/0x265
  [<ffffffff81384bae>] rdev_attr_store+0x89/0xa8
  [<ffffffff8115a96a>] sysfs_write_file+0x108/0x144
  [<ffffffff81106b87>] vfs_write+0xb1/0x10d
  [<ffffffff8106e6c0>] ? trace_hardirqs_on_caller+0x111/0x135
  [<ffffffff81106cac>] sys_write+0x4d/0x77
  [<ffffffff814fe702>] system_call_fastpath+0x16/0x1b
 Code:  Bad RIP value.
 RIP  [<          (null)>]           (null)
  RSP <ffff880085757df0>
 CR2: 0000000000000000
 ---[ end trace ba5fc64319a826fb ]---
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Make use of is_power_of_2 macro.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Add check to determine if a device needs full resync or if partial resync will do

RAID 5 was assuming that if a device was not In_sync, it must undergo a full
resync.  We add a check to see if 'saved_raid_disk' is the same as 'raid_disk'.
If it is, we can safely skip the full resync and rely on the bitmap for
partial recovery instead.  This is the legitimate purpose of 'saved_raid_disk',
from md.h:
int saved_raid_disk;            /* role that device used to have in the
                                 * array and could again if we did a partial
                                 * resync from the bitmap
                                 */
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Add bitmap support to the device-mapper specific metadata area.

This patch allows the creation of the bitmap metadata area upon
initial array creation via device-mapper.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Add the 'sync_super' function pointer to MD array structure (struct mddev_s)

If device-mapper (dm-raid.c) is to define its own on-disk superblock and be
able to load it, there must still be a way for MD to initiate superblock
updates.  The simplest way to make this happen is to provide a pointer in
the MD array structure that can be set by device-mapper (or other module)
with a function to do this.  If the function has been set, it will be used;
otherwise, the method with be looked up via 'super_types' as usual.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)

Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Move personality and sync/recovery thread starting outside md_run.

Moving the wakeup's of the personality and sync/recovery threads out of
md_run and into do_md_run and mddev_resume solves two issues:
1) It allows bitmap_load to be called before the sync_thread is run and
2) when MD personalities are used by device-mapper (dm-raid.c), the start-up
of the array is better alligned with device-mapper primatives
(CTR/resume/suspend/DTR).  I/O - in this case, recovery operations - should
not happen until after a resume has taken place.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Make message a bit clearer by s/blocks/k/

I chose 'k' vs 'kiB' or 'kB' because it is what is used earlier in the
message.  'k' may be a bit ambigous, but I think it's better than "blocks"
which normally means 512, but means 1024 in MD.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Disallow resync I/O while the RAID array is suspended.

Recovery, resync, and metadata I/O should not be allowed while a device is
suspended.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Don't attempt md_integrity_register if there is no gendisk struct available.

When MD arrays are built via device-mapper, the gendisk structure is not
available via mddev.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Al Viro observes that in the hugetlb case, handle_mm_fault() may return
a value of the kind ENOSPC when its caller is expecting a value of the
kind VM_FAULT_SIGBUS: fix alloc_huge_page()'s failure returns.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: usb - turn off de-emphasis in s/pdif for cm6206
  ALSA: asihpi: Use angle brackets for system includes
  ALSA: fm801: add error handling if auto-detect fails
  ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
  ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
  ALSA: 6fire: Don't leak firmware in error path
  ASoC: Fix wm_hubs input PGA ZC bits
  ASoC: Fix dapm_is_shared_kcontrol so everything isn't shared

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (max6642): Better chip detection schema
  hwmon: (coretemp) Further relax temperature range checks
  hwmon: (coretemp) Fix TjMax detection for older CPUs
  hwmon: (coretemp) Relax target temperature range check
  hwmon: (max6642) Rename temp_fault sysfs attribute to temp2_fault

* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
  ARM: Tegra: Harmony: Fix conflicting GPIO numbering

Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.

To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.

This fixes a regression introduced by commit
6f168f2f.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NColin Cross <ccross@android.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (25 commits)
  btrfs: fix uninitialized variable warning
  btrfs: add helper for fs_info->closing
  Btrfs: add mount -o inode_cache
  btrfs: scrub: add explicit plugging
  btrfs: use btrfs_ino to access inode number
  Btrfs: don't save the inode cache if we are deleting this root
  btrfs: false BUG_ON when degraded
  Btrfs: don't save the inode cache in non-FS roots
  Btrfs: make sure we don't overflow the free space cache crc page
  Btrfs: fix uninit variable in the delayed inode code
  btrfs: scrub: don't reuse bios and pages
  Btrfs: leave spinning on lookup and map the leaf
  Btrfs: check for duplicate entries in the free space cache
  Btrfs: don't try to allocate from a block group that doesn't have enough space
  Btrfs: don't always do readahead
  Btrfs: try not to sleep as much when doing slow caching
  Btrfs: kill BTRFS_I(inode)->block_group
  Btrfs: don't look at the extent buffer level 3 times in a row
  Btrfs: map the node block when looking for readahead targets
  Btrfs: set range_start to the right start in count_range_bits
  ...

Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: NPer Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Fix oops caused by queue refcounting failure

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
  tg3: Fix tg3_skb_error_unmap()
  net: tracepoint of net_dev_xmit sees freed skb and causes panic
  drivers/net/can/flexcan.c: add missing clk_put
  net: dm9000: Get the chip in a known good state before enabling interrupts
  drivers/net/davinci_emac.c: add missing clk_put
  af-packet: Add flag to distinguish VID 0 from no-vlan.
  caif: Fix race when conditionally taking rtnl lock
  usbnet/cdc_ncm: add missing .reset_resume hook
  vlan: fix typo in vlan_dev_hard_start_xmit()
  net/ipv4: Check for mistakenly passed in non-IPv4 address
  iwl4965: correctly validate temperature value
  bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
  ath9k: fix two more bugs in tx power
  cfg80211: don't drop p2p probe responses
  Revert "net: fix section mismatches"
  drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
  sctp: stop pending timers and purge queues when peer restart asoc
  drivers/net: ks8842 Fix crash on received packet when in PIO mode.
  ip_options_compile: properly handle unaligned pointer
  iwlagn: fix incorrect PCI subsystem id for 6150 devices
  ...

With Linus' tree, today's linux-next build (powercp ppc64_defconfig)
produced this warning:

fs/btrfs/delayed-inode.c: In function 'btrfs_delayed_update_inode':
fs/btrfs/delayed-inode.c:1598:6: warning: 'ret' may be used
uninitialized in this function

Introduced by commit 16cdcec7 ("btrfs: implement delayed inode items
operation").

This fixes a bug in btrfs_update_inode(): if the returned value from
btrfs_delayed_update_inode is a nonzero garbage, inode stat data are not
updated and several call paths may hit a BUG_ON or fail with strange
code.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid Sterba <dsterba@suse.cz>

wrap checking of filesystem 'closing' flag and fix a few missing memory
barriers.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>

This makes the inode map cache default to off until we
fix the overflow problem when the free space crcs don't fit
inside a single page.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

With the removal of the implicit plugging scrub ends up doing more and
smaller I/O than necessary. This patch adds explicit plugging per chunk.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

commit 4cb5300b ("Btrfs: add mount -o auto_defrag") accesses inode
number directly while it should use the helper with the new inode
number allocator.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

With xfstest 254 I can panic the box every time with the inode number caching
stuff on.  This is because we clean the inodes out when we delete the subvolume,
but then we write out the inode cache which adds an inode to the subvolume inode
tree, and then when it gets evicted again the root gets added back on the dead
roots list and is deleted again, so we have a double free.  To stop this from
happening just return 0 if refs is 0 (and we're not the tree root since tree
root always has refs of 0).  With this fix 254 no longer panics.  Thanks,
Signed-off-by: NJosef Bacik <josef@redhat.com>
Tested-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

In degraded mode the struct btrfs_device of missing devs don't have
device->name set. A kstrdup of NULL correctly returns NULL. Don't
BUG in this case.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

This adds extra checks to make sure the inode map we are caching really
belongs to a FS root instead of a special relocation tree.  It
prevents crashes during balancing operations.
Signed-off-by: NLiu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The free space cache uses only one page for crcs right now,
which means we can't have a cache file bigger than the
crcs we can fit in the first page.  This adds a check to
enforce that restriction.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The nitems counter needs to start at zero
Signed-off-by: NChris Mason <chris.mason@oracle.com>

The current scrub implementation reuses bios and pages as often as possible,
allocating them only on start and releasing them when finished. This leads
to more problems with the block layer than it's worth. The elevator gets
confused when there are more pages added to the bio than bi_size suggests.
This patch completely rips out the reuse of bios and pages and allocates
them freshly for each submit.
Signed-off-by: NArne Jansen <sensille@gmx.net>
Signed-off-by: NChris Maosn <chris.mason@oracle.com>

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: Use hlist_entry() for io_context.cic_list.first
  cfq-iosched: Remove bogus check in queue_fail path
  xen/blkback: potential null dereference in error handling
  xen/blkback: don't call vbd_size() if bd_disk is NULL
  block: blkdev_get() should access ->bd_disk only after success
  CFQ: Fix typo and remove unnecessary semicolon
  block: remove unwanted semicolons
  Revert "block: Remove extra discard_alignment from hd_struct."
  nbd: adjust 'max_part' according to part_shift
  nbd: limit module parameters to a sane value
  nbd: pass MSG_* flags to kernel_recvmsg()
  block: improve the bio_add_page() and bio_add_pc_page() descriptions