Not all PIPE_CONTROLs have a length of 2, so remove it from the #define
and make each invocation specify the desired length.
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
[danvet: implement style suggestion from Ben Widawsdy]
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Add the addresses and definitions I care about for Panel Self Refresh, as
documented in the eDP spec.

I'm sending these out before some other patches because this should be a fairly
simple one to get upstream and not require too much fuss (where the others may
have some fuss).

This file is a mess with white spacing. I tried to stay consistent with the
surrounding code.

v2: had some silly mistakes in v1 which Keith caught

Cc: Dave Airlie <airlied@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Idle the GPU before doing any unmaps. We know if VT-d is in use through
an exported variable from iommu code.

This should avoid a known HW issue.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

[Description from: Daniel Vetter]
I've just discussed this quickly with Chris on irc and it's probably
best to just kill the list_empty early bailout. gpu_idle isn't a
fastpath, so who cares. One candidate where we emit commands to the ring
without adding anything onto these lists is e.g. pageflip. There are
probably more.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NKeith Packard <keithp@keithp.com>

We really don't want this to work in the general case; device drivers
*shouldn't* care whether they are behind an IOMMU or not. But the
integrated graphics is a special case, because the IOMMU and the GTT are
all kind of smashed into one and generally horrifically buggy, so it's
reasonable for the graphics driver to want to know when the IOMMU is
active for the graphics hardware.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

To work around a hardware issue, we have to submit IOTLB flushes while
the graphics engine is idle. The graphics driver will (we hope) go to
great lengths to ensure that it gets that right on the affected
chipset(s)... so let's not screw it over by deferring the unmap and
doing it later. That wouldn't be very helpful.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

For the !HAVE_ATOMIC_IOMAP case the stub functions did not call
pagefault_disable/_enable. The i915 driver relies on the map
actually being atomic, otherwise it can deadlock with it's own
pagefault handler in the gtt pwrite fastpath.

This is exercised by gem_mmap_gtt from the intel-gpu-toosl gem
testsuite.

v2: Chris Wilson noted the lack of an include.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38115
Cc: stable@kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

We currently only round up the userspace size to the next page. We
assume that userspace hasn't made a mistake and requested a zero-length
gem object and all through our internal code we then presume that every
object is backed by at least a single page. Fix that oversight and
report EINVAL back to userspace if they try to create a zero length
object.

[danvet: This fixes tests/gem_bad_length]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Use the helper function already employed by the pwrite/pread
functions.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Fixes tests/gem_tiled_pread on my snb. I know, mesa doesn't use this
on gen6+, but I also hate failing testcases.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

The rps disabling code wasn't properly cancelling outstanding work
items. Also add a comment that explains why we're not racing with
the work item that could unmask interrupts - that piece of code
confused me quite a bit.

v2: Ben Widawsky pointed out that the first patch would deadlock
(and a few lesser problems). All corrected.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This patch closes the following race:

We get a PM interrupt A, mask it, set dev_priv->iir = PM_A and kick of the
work item. Scheduler isn't grumpy, so the work queue takes rps_lock,
grabs pm_iir = dev_priv->pm_iir and pm_imr = READ(PMIMR). Note that
pm_imr == pm_iir because we've just masked the interrupt we've got.

Now hw sends out PM interrupt B (not masked), we process it and mask
it.  Later on the irq handler also clears PMIIR.

Then the work item proceeds and at the end clears PMIMR. Because
(local) pm_imr == pm_iir we have
        pm_imr & ~pm_iir == 0
so all interrupts are enabled.

Hardware is still interrupt-happy, and sends out a new PM interrupt B.
PMIMR doesn't mask B (it does not mask anything), PMIIR is cleared, so
we get it and hit the WARN in the interrupt handler (because
dev_priv->pm_iir == PM_B).

That's why I've moved the
        WRITE(PMIMR, 0)
up under the protection of the rps_lock. And write an uncoditional 0
to PMIMR, because that's what we'll do anyway.

This races looks much more likely because we can arbitrarily extend
the window by grabing dev->struct mutex right after the irq handler
has processed the first PM_B interrupt.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Quoting Chris Wilson's more concise description:

"Ah I think I see the problem. As you point out we only mask the current
interrupt received, so that if we have a task pending (and so IMR != 0) we
actually unmask the pending interrupt and so could receive it again before the
tasklet is finally kicked off by the grumpy scheduler."

We need the hw to issue PM interrupts A, B, A while the scheduler is hating us
and refuses to run the rps work item. On receiving PM interrupt A we hit the
WARN because

dev_priv->pm_iir == PM_A | PM_B

Also add a posting read as suggested by Chris to ensure proper ordering of the
writes to PMIMR and PMIIR. Just in case somebody weakens write ordering.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This is general TMDS detect, not HDMI specifically.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

I can't think of any sensible reason to limit this to a mask of 0x0f,
ie, SDVO_OUTPUT_{TMDS,RGB,CVBS,SVID}0.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

I have no evidence for this byte being used this way, and lots of
counterexamples.  Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Conflicts:
	drivers/gpu/drm/i915/intel_dp.c

Just whitespace change conflicts

If the panel is powered up, there's no need to delay for the 'off'
interval when turning the panel on.
Signed-off-by: NKeith Packard <keithp@keithp.com>

This eliminates a fairly long delay when power sequencing newer
hardware
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's no good reason to turn off the eDP force VDD bit synchronously
while probing devices; that just sticks a huge delay into all mode
setting paths. Instead, queue a delayed work proc to disable the VDD
force bit and then remember when that fires to ensure that the
appropriate delay is respected before trying to turn it back on.
Signed-off-by: NKeith Packard <keithp@keithp.com>

We need to check eDP VDD force and panel on in several places, so
create some simple helper functions to avoid duplicating code.
Signed-off-by: NKeith Packard <keithp@keithp.com>

The return value was unused, so just stop doing that.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This value doesn't come directly from the VBT, and so is rather
specific to the particular DP output.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Store the panel power sequencing delays in the dp private structure,
rather than the global device structure. Who knows, maybe we'll get
more than one eDP device in the future.

From the eDP spec, we need the following numbers:

 T1 + T3	Power on to Aux Channel operation (panel_power_up_delay)

		This marks how long it takes the panel to boot up and
		get ready to receive aux channel communications.

 T8		Video signal to backlight on (backlight_on_delay)

		Once a valid video signal is being sent to the device,
		it can take a while before the panel is actuall
		showing useful data. This delay allows the panel
		to get something reasonable up before the backlight
		is turned on.

 T9		Backlight off to video off (backlight_off_delay)

		Turning the backlight off can take a moment, so
		this delay makes sure there is still valid video
		data on the screen.

 T10		Video off to power off (panel_power_down_delay)

		Presumably this delay allows the panel to perform
		an orderly shutdown of the display.

 T11 + T12	Power off to power on (panel_power_cycle_delay)

		So, once you turn the panel off, you have to wait a
		while before you can turn it back on. This delay is
		usually the longest in the entire sequence.

Neither the VBIOS source code nor the hardware documentation has a
clear mapping between the delay values they provide and those required
by the eDP spec. The VBIOS code actually uses two different labels for
the delay values in the five words of the relevant VBT table.

**** MORE LATER ***

Look at both the current hardware register settings and the VBT
specified panel power sequencing timings. Use the maximum of the two
delays, to make sure things work reliably. If there is no VBT data,
then those values will be initialized to zero, so we'll just use the
values as programmed in the hardware. Note that the BIOS just fetches
delays from the VBT table to place in the hardware registers, so we
should get the same values from both places, except for rounding.

VBT doesn't provide any values for T1 or T2, so we'll always just use
the hardware value for that.

The panel power up delay is thus T1 + T2 + T3, which should be
sufficient in all cases.

The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy
for T11, which isn't available anywhere.

For the backlight delays, the eDP spec says T6 + T8 is the delay from the
end of link training to backlight on and T9 is the delay from
backlight off until video off. The hardware provides a 'backlight on'
delay, which I'm taking to be T6 + T8 while the VBT provides something
called 'T7', which I'm assuming is s

On the macbook air I'm testing with, this yields a power-up delay of
over 200ms and a power-down delay of over 600ms. It all works now, but
we're frobbing these power controls several times during mode setting,
making the whole process take an awfully long time.
Signed-off-by: NKeith Packard <keithp@keithp.com>

Any call to intel_dp_sink_dpms must ensure that the panel has power so
that the DP_SET_POWER operation will be correctly received. The only
one missing this was in intel_dp_prepare.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The DP i2c initialization code does a couple of i2c transactions,
which means that an eDP panel must be powered up.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On eDP, DDC requires panel power, but turning that on uses the panel
power sequencing timing values fetch from the DPCD data.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the panel is already off, we'll need to turn VDD on to execute the
(useless) DPMS off code. Yes, it would be better to just not do any of
this, but correctness, and *then* performance.
Signed-off-by: NKeith Packard <keithp@keithp.com>

The VDD force bit is turned on before touching the panel, but if it
was enabled, there was no call to turn it back off. Add a call.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Cleans up code dealing with eDP a bit. Remove redundant checks in
callers
Signed-off-by: NKeith Packard <keithp@keithp.com>

Avoid any question about locked registers by just writing the unlock
pattern with every write to the register.
Signed-off-by: NKeith Packard <keithp@keithp.com>

Verify that the eDP VDD is on, either with the panel being on or with
the VDD force-on bit being set.

This demonstrates that in many instances, VDD is not on when needed,
which leads to failed EDID communications.
Signed-off-by: NKeith Packard <keithp@keithp.com>

We're going to assume that EDID is more reliable than the VBT tables
for eDP panels, which is notably true on MacBook machines where the
VBT contains completely bogus data.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This masks out all interrupts and ack's any pending ones at IRQ
uninstall time to make sure we don't receive any unexpected interrupts
later on.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We were relying on the BIOS to set these bits, which doesn't always
happen.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>