Looks like our L_PTE_S2_RDWR definition is slightly wrong,
and is actually write only (see ARM ARM Table B3-9, Stage 2 control
of access permissions). Didn't make a difference for normal pages,
as we OR the flags together, but I'm still wondering how it worked
for Stage-2 mapped devices, such as the GIC.

Brown paper bag time, again.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

Commit 3401d546 (KVM: ARM: Introduce KVM_ARM_SET_DEVICE_ADDR
ioctl) added support for the KVM_CAP_ARM_SET_DEVICE_ADDR capability,
but failed to add a break in the relevant case statement, returning
the number of CPUs instead.

Luckilly enough, the CONFIG_NR_CPUS=0 patch hasn't been merged yet
(https://lkml.org/lkml/diff/2012/3/31/131/1), so the bug wasn't
noticed.

Just give it a break!
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

This patch fix the regression introduced by the commit 3202bf01
"arm: mvebu: Improve the SMP support of the interrupt controller":
GPIO IRQ were no longer delivered to the CPUs.

To be delivered to a CPU an interrupt must be enabled at CPU level and
at interrupt source level. Before the offending patch, all the
interrupts were enabled at source level during map() function. Mask()
and unmask() was done by handling the per-CPU part. It was fine when
running in UP with only one CPU.

The offending patch added support for SMP, in this case mask() and
unmask() was done by handling the interrupt source level part. The
per-CPU level part was handled by the affinity API to select the CPU
which will receive the interrupt. (Due to some hardware limitation
only one CPU at a time can received a given interrupt).

For "normal" interrupt __setup_irq() was called when an irq was
registered. irq_set_affinity() is called from this function, which
enabled the interrupt on one of the CPUs. Whereas for GPIO IRQ which
were chained interrupts, the irq_set_affinity() was never called and
none of the CPUs was selected to receive the interrupt.

With this patch all the interrupt are enable on the current CPU during
map() function. Enabling the interrupts on a CPU doesn't depend
anymore on irq_set_affinity() and then the chained irq are not anymore
a special case. However the CPU which will receive the irq can still
be modify later using irq_set_affinity().

Tested with Mirabox (A370) and Openblocks AX3 (AXP), rootfs mounted
over NFS, compiled with CONFIG_SMP=y/N.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: NRyan Press <ryan@presslab.us>
Investigated-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NRyan Press <ryan@presslab.us>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The external pending interrupt register address (EINTPEND) offset is
0xa8, not 0x08. Without this patch the external interrupts are not
properly acknowledged, which may lead to an interrupt storm and the
system hang as soon as any external interrupt is requested.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Due to NR_IRQS being incorrectly defined not all IRQ domains can
be registered for S3C2440. It causes following errors on a s3c2440
SoC based board:

NR_IRQS:89
S3C2440: IRQ Support
irq: clearing pending status 00000002
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:234 0xc0056ed0()
...
irq: could not create irq-domain
...
s3c2410-wdt s3c2410-wdt: failed to install irq (-22)
s3c2410-wdt: probe of s3c2410-wdt failed with error -22
...
samsung-uart s3c2440-uart.0: cannot get irq 74

Fix this by increasing NR_IRQS to at least (IRQ_S3C2443_AC97 + 1)
if CPU_S3C2440 is selected, so the subintc IRQ domain gets properly
registered.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to the recent i.MX6 Quad technical reference manual, mode 0x4 (100b)
of the CCM_CS2DCR register (address 0x020C402C) bits [11-9] and [14-12] select
the PLL3 clock, and not the PLL3 PFD1 540M clock. In our code, the PLL3 root
clock is named 'pll3_usb_otg', select this instead of the 540M clock.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

While booting from device tree, imx6q used to provide twd clock lookup
by calling clk_register_clkdev() in clock driver.  However, the commit
bd603455 (ARM: use device tree to get smp_twd clock) forces DT boot to
look up the clock from device tree.  It causes the failure below when
twd driver tries to get the clock, and hence kernel has to calibrate the
local timer frequency.

 smp_twd: clock not found -2
 ...
 Calibrating local timer... 396.13MHz.

Fix the regression by providing twd clock lookup from device tree, and
remove the unused twd clk_register_clkdev() call from clock driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The admux clock seems to be the audmux clock as tests show. audmux does
not work without this clock enabled. Currently imx35 does not register a
clock device for audmux. This patch adds this registration. imx-audmux
driver already handles a clock device, so no changes are necessary
there.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch enables iomuxc_gate clock. It is necessary to be able to
reconfigure iomux pads. Without this clock enabled, the
clk_disable_unused function will disable this clock and the iomux pads
are not configurable anymore. This happens at every boot. After a reboot
(watchdog system reset) the clock is not enabled again, so all iomux pad
reconfigurations in boot code are without effect.

The iomux pads should be always configurable, so this patch always
enables it.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Let's do the changes properly and fix the same problem everywhere, not
just for one case.

Cc: <stable@vger.kernel.org> # kernels containing 15e0d9e3 or equivalent
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.

The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 70264367 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.

This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:

1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
   one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
   return code already).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit b8db6b88 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d060 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb8 (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b88 also caused the printed cache
ID to be missing the version information.

Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: NPaolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1

This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built.  Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Slow down the I2C clock speed on M28 and SPS1 as it turns out the
I2C block in i.MX28 can not operate stable enough with the bus
running at 400kHz. Note that the driver used by Freescale runs
the bus at 250kHz when 400kHz speed is selected, but the mainline
Linux kernel runs the bus at actual 400kHz and that's where it is
occasionally unstable. Play safe and run the bus at 100kHz.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

In the conversion to pinctrl, an error in the pins for the rebuild
LED was introduced. This patch assigns the correct pins and includes
the correct name for the LED in kirkwood-iomega_ix2_200.dts.
Signed-off-by: NNigel Roberts <nigel@nobiscuit.com>
Cc: <stable@vger.kernel.org> # v3.8.x
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Since commit 0536bdf3 (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.

This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.
Signed-off-by: NMac Lin <mkl0301@gmail.com>
Signed-off-by: NAnton Vorontsov <anton@enomsg.org>
Cc: stable@vger.kernel.org [v3.3+]

The previous configuration used the wrong "clk" pin.  Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.

I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: NRyan Press <ryan@presslab.us>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The crypto functionality in the orion5x dtsi uses the Ethernet IRQ and
so things do not work and there is much grumbling at boot time.
The IRQ for the crypto should be 28, and not 22, and that is what this
patch corrects.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

orion5x.dtsi is missing the gpio alias as well as including a typo
('ngpio' instead of 'ngpios') that prevented the orion-gpio driver
from loading.  Also missing were the interrupt-controller properties.
This patches resolves those glitches.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

mvsdio_platform_data allows to pass card detect and write protect gpio
numbers to the driver. Some kirkwood boards don't use both pins as they
are not connected, and don't set the corresponding value in platform_data.

This will leave the unset values in platform_data initialized as 0, which
is in fact a valid gpio pin. mvsdio will grab that pin and configure it as
gpio, which in turn breaks nand controller as mpp0 also carries nand_io2.

This patch fixes the above by initializing unused gpio functions in the
platform_data with an invalid (-1) value.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The commit 3a6f08a3 "arm: mvebu: Add support for local interrupt",
managed the 28th first interrupts as local interrupt to match the
hardware specification. Among these interrupts there are the Gigabits
Ethernet ones used by the mvneta driver. Unfortunately the state of
the percpu_irq API prevents the driver to use it.

Indeed the interrupts have to be freed when the .stop() function is
called. As the free_percpu_irq() function don't disable the interrupt
line, we have to do it on each CPU before calling this. The function
disable_percpu_irq() only disable the percpu on the current CPU and
there is no function which allows to disable a percpu irq on a given
CPU. Waiting for the extension of the percpu_irq API, this fix allows
to use again the mvneta driver.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.

The basic problem was discussed at http://forum.doozan.com/read.php?2,7451Signed-off-by: NEric Hutter <hutter.eric@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This fixes a regression introduced by common clk enablement.

On some u8500 based boards, the FMSC clock which is usually used
for flash, is wired up to the SMSC911x Ethernet driver. However,
the SMSC911x doesn't have common clk support yet, rendering it
unusable. Prior to the introduction of common clk the FMSC clock
was default on; however, common clk disables all clocks by default
and insists drivers take responsibility to enable theirs.

This fix enables the FMSC clock on Snowball, subsequently turning
on the SMSC911x Ethernet chip. It will be removed when the driver
is compatible with common clk.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This fixes a regression introduced during the v3.9 merge window.

Now MMCI on/off functionality is using the regulator framework
from the MMCI driver, if we provide the ios_handler call-back we
essentially duplicate functionality, which causes a large mess
and lots of booting issues.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This fixes a regression introduced by commit:
  05ec260e mfd:db8500-prcmu: update resource passing

All DBx5x0 based SoCs have access to two Tightly Coupled Memory
(TCM) locations based on the PRCMU itself. One area from program
memory (TCPM) and one for data memory (TCDM). The PRCMU needs to
know where these are in order to function correctly. However,
these are currently passed though platform device resources, which
can only be obtained if Device Tree booting isn't in use. Thus we
must also support them in DT by supplying them through the PRCMU
node.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

clk inits on OMAP happen quite early, even before slab is available.
The dependency comes from the fact that the timer init code starts to
use clocks and hwmod and we need clocks to be initialized by then.

There are various problems doing clk inits this early, one is,
not being able to do dynamic clk registrations and hence the
dependency on clk-private.h. The other is, inability to debug
early kernel crashes without enabling DEBUG_LL and earlyprintk.

Doing early clk init also exposed another instance of a kernel
panic due to a BUG() when CONFIG_DEBUG_SLAB is enabled.

[    0.000000] Kernel BUG at c01174f8 [verbose debug info unavailable]
[    0.000000] Internal error: Oops - BUG: 0 [#1] SMP ARM
[    0.000000] Modules linked in:
[    0.000000] CPU: 0    Not tainted  (3.9.0-rc1-12179-g72d48f9 #6)
[    0.000000] PC is at __kmalloc+0x1d4/0x248
[    0.000000] LR is at __clk_init+0x2e0/0x364
[    0.000000] pc : [<c01174f8>]    lr : [<c0441f54>]    psr: 600001d3
[    0.000000] sp : c076ff28  ip : c065cefc  fp : c0441f54
[    0.000000] r10: 0000001c  r9 : 000080d0  r8 : c076ffd4
[    0.000000] r7 : c074b578  r6 : c0794d88  r5 : 00000040  r4 : 00000000
[    0.000000] r3 : 00000000  r2 : c07cac70  r1 : 000080d0  r0 : 0000001c
[    0.000000] Flags: nZCv  IRQs off  FIQs off  Mode SVC_32  ISA ARM  Segment kernel
[    0.000000] Control: 10c53c7d  Table: 8000404a  DAC: 00000017
[    0.000000] Process swapper (pid: 0, stack limit = 0xc076e240)
[    0.000000] Stack: (0xc076ff28 to 0xc0770000)
[    0.000000] ff20:                   22222222 c0794ec8 c06546e8 00000000 00000040 c0794d88
[    0.000000] ff40: c074b578 c076ffd4 c07951c8 c076e000 00000000 c0441f54 c074b578 c076ffd4
[    0.000000] ff60: c0793828 00000040 c0794d88 c074b578 c076ffd4 c0776900 c076e000 c07272ac
[    0.000000] ff80: 2f800000 c074c968 c07f93d0 c0719780 c076ffa0 c076ff98 00000000 00000000
[    0.000000] ffa0: 00000000 00000000 00000000 00000001 c074cd6c c077b1ec 8000406a c0715724
[    0.000000] ffc0: 00000000 00000000 00000000 00000000 00000000 c074c968 10c53c7d c0776974
[    0.000000] ffe0: c074cd6c c077b1ec 8000406a 411fc092 00000000 80008074 00000000 00000000
[    0.000000] [<c01174f8>] (__kmalloc+0x1d4/0x248) from [<c0441f54>] (__clk_init+0x2e0/0x364)
[    0.000000] [<c0441f54>] (__clk_init+0x2e0/0x364) from [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140)
[    0.000000] [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140) from [<c0719780>] (setup_arch+0x15c/0x284)
[    0.000000] [<c0719780>] (setup_arch+0x15c/0x284) from [<c0715724>] (start_kernel+0x7c/0x334)
[    0.000000] [<c0715724>] (start_kernel+0x7c/0x334) from [<80008074>] (0x80008074)
[    0.000000] Code: e5883004 e1a00006 e28dd00c e8bd8ff0 (e7f001f2)
[    0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[    0.000000] Kernel panic - not syncing: Attempted to kill the idle task!

It was a know issue, that slab allocations would fail when common
clock core tries to cache parent pointers for mux clocks on OMAP,
and hence a patch 'clk: Allow late cache allocation for clk->parents,
commit 7975059d' was added to work this problem around.
A BUG() within kmalloc() with CONFIG_DEBUG_SLAB enabled was completely
overlooked causing this regression.

More details on the issue reported can be found here,
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg85932.html

With all these issues around clk inits happening way too early, it
makes sense to at least move them to a point where dynamic memory
allocations are possible. So move them to a point just before the
timer code starts using clocks and hwmod.

This should at least pave way for clk inits on OMAP moving to dynamic
clock registrations instead of using the static macros defined in
clk-private.h.

The issue with kernel panic while CONFIG_DEBUG_SLAB is enabled
was reported by Piotr Haber and Tony Lindgren and this patch
fixes the reported issue as well.
Reported-by: NPiotr Haber <phaber@broadcom.com>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: NMike Turquette <mturquette@linaro.org>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org  # v3.8
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is a sync issue with hotplug operation.  It's possible that when
imx_cpu_kill gets running on primary core, the imx_cpu_die execution
on the core which is to be killed hasn't been finished yet.  The problem
will very likely be hit when running suspend without no_console_suspend
setting on kernel cmdline.

It uses cpu jumping argument register to sync imx_cpu_die and
imx_cpu_kill.  The register will be set in imx_cpu_die and imx_cpu_kill
will wait for the register being cleared to actually kill the cpu.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>

Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

If the clockevent is forcibly reprogrammed to have a different
match value we mistakenly assume the timer is not ticking and
program a new match value while the timer is running. Although we
clear the timer before programming a new match, it's better to
stop the timer before clearing it so that we're sure the proper
amount of ticks are counted. Failure to do so can lead to missed
ticks and system hangs.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>

CPU debug features like hardware break, watchpoints can be used only
when the debug mode is enabled and available. Unfortunately on OMAP4
based devices, after a CPU power cycle, the debug feature gets disabled
which leads to a flood of messages coming from reset_ctrl_regs() which
gets called on every CPU_PM_EXIT with CPUidle enabled.

So make use of warn_once() so that system is usable.

Thanks to Will for pointers and Lokesh for the analysis of the issue.
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some early versions of the Krait CPU design incorrectly indicate
that they only support the UDIV and SDIV instructions in Thumb
mode when they actually support them in ARM and Thumb mode. It
seems that these CPUs follow the DDI0406B ARM ARM which has two
possible values for the divide instructions field, instead of the
DDI0406C document which has three possible values.

Work around this problem by checking the MIDR against Krait CPUs
with this faulty ISAR0 register and force the hwcaps to indicate
support in both modes.

[sboyd: Rewrote commit text to reflect real reasoning now that
	we autodetect udiv/sdiv]
Signed-off-by: NStepan Moskovchenko <stepanm@codeaurora.org>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ISAR0 register indicates support for the SDIV and UDIV
instructions in both the Thumb and ARM instruction set. Read the
register to detect the supported instructions and update the
elf_hwcap mask as appropriate. This is better than adding more
and more cpuid checks in proc-v7.S for each new cpu variant that
supports these instructions.
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Don't advertise support for the SDIV/UDIV thumb instructions if
the kernel is not compiled with support for thumb userspace. This
is in line with how we remove the THUMB hwcap in these
configurations.
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

With LPAE enabled, alloc_init_section() does not map the entire
address space for unaligned addresses.

The issue also reproduced with CMA + LPAE. CMA tries to map 16MB
with page granularity mappings during boot. alloc_init_pte()
is called and out of 16MB, only 2MB gets mapped and rest remains
unaccessible.

Because of this OMAP5 boot is broken with CMA + LPAE enabled.
Fix the issue by ensuring that the entire addresses are
mapped.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <chris@cloudcar.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NLaura Abbott <lauraa@codeaurora.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NChristoffer Dall <chris@cloudcar.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

While adding i.MX DEBUG_LL selection, commit f8c95fe6 (ARM: imx: support
DEBUG_LL uart port selection for all i.MX SoCs) leaves Kconfig symbol
DEBUG_IMX_UART_PORT there without any dependency check.  This results in
that everyone gets the symbol in their config, which is someting
undesirable.  Add "depends on ARCH_MXC" for the symbol to prevent that.
Reported-by: NKarl Beldan <karl.beldan@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The issue fixed by this patch manifests only then using X11
with mxsfb driver. The X11 will display either shifted image
or otherwise distorted image on the LCD.

The problem is that the X11 tries to reconfigure the framebuffer
and along the way calls fb_ops.fb_set_par() with X11's desired
configuration values. The field of particular interest is
fb_info->var.sync which contains non-standard values if
configured by kernel. These are either FB_SYNC_DATA_ENABLE_HIGH_ACT,
FB_SYNC_DOTCLK_FAILING_ACT or both, depending on the platform
configuration. Both of these values are defined in the
include/linux/mxsfb.h file.

The driver interprets these values and configures the LCD controller
accordingly. Yet X11 only has access to the standard values for this
field defined in include/uapi/linux/fb.h and thus, unlike kernel,
omits these special values. This results in distorted image on the
LCD.

This patch moves these non-standard values into new field of the
mxsfb_platform_data structure so the driver can in turn check this
field instead of the video mode field for these specific portions.

Moreover, this patch prefixes these values with MXSFB_SYNC_ prefix
instead of FB_SYNC_ prefix to prevent confusion of subsequent users.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM <linux-arm-kernel@lists.infradead.org>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Lothar Waßmann <LW@karo-electronics.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>