We need to assume that all features will be available when registering the
netdev otherwise they are ommitted from the initial set of
dev->wanted_features. When we connect to the backed we reduce the set as
necessary due to the call to netdev_update_features() in xennet_connect().
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On error path kfree() should get pointer to memory allocated by
kmalloc() not the address of variable holding it (which is on stack).
Signed-off-by: NMariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Must declare xennet_fix_features() and xennet_set_features() before
using them.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Side effects:
 - TX offloads (HW csum, scatter-gather) can be toggled now
 - RX checksum is reported correctly now (it's always active)
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should probably get TSO available as it's basically a loopback device.
Offloads are left disabled by default - as before.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not tested in any way. The original code for offload setting seems broken
as it resets the features on every netback reconnect.

This will set GSO_ROBUST at device creation time (earlier than connect time).

RX checksum offload is forced on - so advertise as it is.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a race (not fixed here) in smsc75xx in setting RFE_CTL that's not
properly handled via rfe_ctl_lock. Spinlock is not a good tool here, as
this has to wait for URB completion (or maybe just submission) after issuing
register write request. Otherwise, the rfe_ctl might be changed just after
spin_unlock() and device left programmed with other value.

smsc95xx has increased hard_header_len for the case of TX checksumming.

smsc75xx is fixed to advertise IP+IPV6_CSUM instead of HW_CSUM as it does
not use csum_start/csum_offset.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.

Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().

Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.

The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two.  The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: NArnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: NAndy Green <andy.green@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we have CONFIG_ARCH_DMA_ADDR_T_64BIT. We can fix the hacky
dma_addr_t size test cleanly.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With current bnx2x firmware 6.2.9, iSCSI is not supported in DCB
network, so we need to disable it.  Add cnic command to disconnect
iSCSI connections and prevent future connections when DCBX negotiation
succeeds.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We could get hardware attention during DCB/FCoE traffic without this
fix.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To fix bugs when running offloaded FCoE/iSCSI traffic in multiple
Class of Service environments.  In some scenarios, traffic could stop
on certain rings and eventually all traffic would stop.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should reduce the number of reserved completion queues from the total
number of entries. Since the queue size is power of two, not reducing the
reserved entries, caused a double queue size, which may lead to allocation
failures in some cases.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of allocation failure, tried to use the promiscuous QP
entry that was previously freed.
Now freeing this entry only in case we will not put it back to the list
of promiscuous entries.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use accumulates instead of acumulates.
Signed-off-by: NPan Weiping <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IRQF_SAMPLE_RANDOM flag is marked as deprecated and will be removed.

Every input point to the kernel's entropy pool have to better document the
type of entropy source it is.

drivers/char/random.c now implements a set of interfaces that can be used for
devices to collect enviromental noise. IRQF_SAMPLE_RANDOM will be replaced
with these add_*_randomness exported functions.

Network drivers are not a good source of entropy. They use as a source of
entropy essentially a remote host. Which means that the source of entropy can
be potentially controlled by an attacker. Also, with heavy workloads the
entropy decreases due to less hardware interrupts happening thanks to irq
mitigation and NAPI.

If a system relies in its network interface as a entropy source it has a false
sense of security. Systems that don't have devices whose drivers are good
sources of entropy, should either use a hardware random number generator or
feed the kernel's entropy pool from userspace using other sources of entropy
such as EGD, video_entropyd, timer_entropyd and audio-entropyd.
Signed-off-by: NJavier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current enic code only supports ASSOCIATE and DISASSOCIATE port profile
operations. This patch adds enic support for port profile
PORT_REQUEST_PREASSOCIATE_RR operation. The VIC adapter (8021qbh) is capable
of handling port profile requests done in two steps namely PREASSOCIATE_RR
and ASSOCIATE today. The motivation to support PREASSOCIATE_RR comes mainly
from its use as an optimization during VM migration ie, to do resource
reservation on destination host before resources on source host are released.

PREASSOCIATE_RR is a VDP operation and according to the latest at IEEE,
8021qbh will also need to support VDP commands.

In addition to handling the new PORT_REQUEST_PREASSOCIATE_RR operation
this patch also does the below:
- Introduces handlers for PORT_REQUEST operations
- Moves most of the port profile handling code to new files enic_pp.[ch]
- Uses new fw devcmds for port profile operations
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does the following:
- Introduces a new macro VIC_PROVINFO_ADD_TLV
- Adds a new OS type in vic_generic_prov_os_type
- Changes some vic_provinfo* helper routine args to constants
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds wrapper routines to new port profile related fw devcmds and
removes the old ones
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces new fw devcmds for port profile handling.
These new commands are similar to the current fw commands for
port profile handling. The only difference being that the new
commands split the existing port profile handling devcmds into multiple
fw commands, giving the driver finer control over port profile operations.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by sparse:
drivers/net/via-rhine.c:1706:16: warning: cast to restricted __be16
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more common/verbose logging styles.

Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove smsc911x prefixes from format strings.
Rename SMSC_WARNING to SMSC_WARN.
Remove DPRINTK macro.
Use netif_<level> in SMSC_<level> macros.
Convert NETIF_MSG_<foo> uses to lower case.
Add no_printk verification in non-debug uses.
Add pdata to SMSC_<level> uses to avoid hidden variable uses.
Convert printks to netdev_<level> as appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the be_worker() workqueue is scheduled in be_probe() it must
be canceled unconditionally in be_shutdown().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code has been refactored to not set num_rx_qs inside be_enable_msix().
num_rx_qs is now set at the time of queue creation based on the number of
available msix vectors.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support RTL8168E/RTL8111E.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new chip for RTL8168DP.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new chip for RTL8105 whose settings are the same with RTL_GIGA_MAC_VER_30.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commits 01a16b21 (netlink: kill eff_cap from struct netlink_skb_parms)
and c53fa1ed (netlink: kill loginuid/sessionid/sid members from struct
netlink_skb_parms) removed some members from struct netlink_skb_parms
that depend on the current context, all netlink users are now required
to do synchronous message processing.

connector however queues received messages and processes them in a work
queue, which is not valid anymore. This patch converts connector to do
synchronous message processing by invoking the registered callback handler
directly from the netlink receive function.

In order to avoid invoking the callback with connector locks held, a
reference count is added to struct cn_callback_entry, the reference
is taken when finding a matching callback entry on the device's queue_list
and released after the callback handler has been invoked.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.

We no longer use release_vccs() so we can delete it.

release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.
Signed-off-by: NPhilip A. Prindeville <philipp@redfish-solutions.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.

Also include the size, vpi, and vci in the debug as is done on
receive.

Use "port" consistently instead of "device" intermittently.
Signed-off-by: NPhilip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use VPI.VCI notation consistently throughout the module. This is the
one remaining place where the VCI is used before the VPI in any output.
Signed-off-by: NPhilip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We leak in some error paths of drivers/net/atlx/atl2.c:atl2_set_eeprom().
The memory allocated to 'eeprom_buff' is not freed when we return -EIO.
This patch fixes that up and also removes a pointless explicit cast.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>