When the firmware is issuing events to the driver the events
must be removed from the queue.  If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:

1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limitation to only 1500 byte mtu's limits the utility of the veth
device for testing routing.  So implement implement a configurable
MTU.

For consistency I drop packets on the receive side when they are
larger than the MTU.  I count those drops.  And I allow
a little padding for vlan headers.

I also test the mtu when a new device is created with netlink
because that path currently bypasses the current mtu setting
code.
Signed-off-by: NEric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix RDS Infiniband dependencies for RDMA so that these
build errors won't happen:

ERROR: "rdma_accept" [net/rds/rds.ko] undefined!
ERROR: "rdma_destroy_id" [net/rds/rds.ko] undefined!
ERROR: "rdma_connect" [net/rds/rds.ko] undefined!
ERROR: "rdma_destroy_qp" [net/rds/rds.ko] undefined!
ERROR: "rdma_listen" [net/rds/rds.ko] undefined!
ERROR: "rdma_notify" [net/rds/rds.ko] undefined!
ERROR: "rdma_create_id" [net/rds/rds.ko] undefined!
ERROR: "rdma_create_qp" [net/rds/rds.ko] undefined!
ERROR: "rdma_bind_addr" [net/rds/rds.ko] undefined!
ERROR: "rdma_resolve_route" [net/rds/rds.ko] undefined!
ERROR: "rdma_disconnect" [net/rds/rds.ko] undefined!
ERROR: "rdma_reject" [net/rds/rds.ko] undefined!
ERROR: "rdma_resolve_addr" [net/rds/rds.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o set port mode after resetting device.
o prefer cut-through firmware (doesn't require on-card memory).
o load flashed firmware if newer.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support larger dma mask if firmware indicates capability
to handle larger addresses.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit faee47cd
(sctp: Fix the RTO-doubling on idle-link heartbeats)
broke the RTO doubling for data retransmits.  If the
heartbeat was sent before the data T3-rtx time, the
the RTO will not double upon the T3-rtx expiration.
Distingish between the operations by passing an argument
to the function.

Additionally, Wei Youngjun pointed out that our treatment
of requested HEARTBEATS and timer HEARTBEATS is the same
wrt resetting congestion window.  That needs to be separated,
since user requested HEARTBEATS should not treat the link
as idle.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions time_before or time_after are more robust
for comparing jiffies against other values.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code in sctp_getsockopt_maxburst() doesn't allow len to be larger
then struct sctp_assoc_value, which is a common case where app writers
just pass down the sizeof(buf) or something similar.

This patch fix the problem.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove dup check of "if (optlen < sizeof(int))".
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the type name "AUTH" and primitive type name
"PRIMITIVE_ASCONF" for debug message.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The above functions from include/net/tcp.h have been defined with an
argument that they never use. The argument is 'u32 ack' which is never
used inside the function body, and thus it can be removed. The rest of
the patch involves the necessary changes to the function callers of the
above two functions.
Signed-off-by: NHantzis Fotis <xantzis@ceid.upatras.gr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a
lot of different regions in the chip - to keep the code as clean as possible,
the ranges were put in an H file. Some areas cannot be read if the driver is
running - so by default, the driver will not access those areas - but any
programmer facing a problem will be able to easily manipulate the driver to
extract full dump. The full dump can also be used with kernel dump modules in
case of kernel panic.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the FP index to relevant debug prints and simply beautify some others
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 8726 module detection option is disabled, module should be transmitting
regardless of invalid read from EEPROM
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Microcode download requires write of another register and read from
"Limiting/LRM mode" register before setting
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On unload, the FW assumes that no packets will be sent after the driver sends
the FW stop command. To ensure that, the driver must always call
netif_tx_disable
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using DMA engine (DMAE) to initialize large consecutive memories in the chip
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the napi_poll budget only when updating it. Also add a comment to explain
the rmb
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx interrupt is very short and there is no need to limit it to a budget
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rmb to read status block indices on load
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the comment explains, this smb_mb is needed only if the queue is stopped
(which is unlikely) so the barrier can be moved to that location
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noted by Ben Hutchings <bhutchings@solarflare.com>, these are the
capabilities offsets and not the ID itself
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noted by Ben Hutchings <bhutchings@solarflare.com>, these smb_mb are not
needed
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conversion to avoid using pci_alloc_consistent() broke the firmware
load process, as well as added an order-4 kmalloc and doubled the memory
usage of the firmware image. Go back to loading a page at a time.

Also, since the user can now give us utter garbage for firmware, do a
cursory validation so we don't try to load just anything.
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>