Handle VHT rates like HT ones, otherwise we easily trigger the pre-HT
rates WARN_ON(rc_rate->idx >= sband->n_bitrates) which will set
rc_rate->idx to -1.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the 1st rate control entry is a pre-HT rate we want to set
rts_cts_rate_idx "as the fastest basic rate that is not faster than the
data rate"(code comments).
But in case some bss allowed rate indexes are lower than the lowest bss
basic rate, if the rate control selects a rate among the formers for its
1st rate control entry, rts_cts_rate_idx remains 0 and is not a basic
rate index.
This commit sets rts_cts_rate_idx to the lowest bss basic rate index in
this situation.

Note that the code assumes that lowest indexes == lowest bitrates.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of having an SKB all the time, use a beacon_data struct
with just the information required. This also allows removing a
synchronize_rcu() and using kfree_rcu() instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make the TX bytes/packets counters race-free by keeping
them per AC so concurrent TX on queues can't cause lost
or wrong updates. This works since each station belongs
to a single interface. While at it also make the bytes
counters 64-bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Introduced with de74a1d9
"mac80211: fix WPA with VLAN on AP side with ps-sta".
Apparently overwrites the sdata pointer with non-valid data in
the case of mesh.
Fix this by checking for IFTYPE_AP_VLAN.
Signed-off-by: NMarco Porsch <marco@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert to the much saner new idr interface.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 6c17b77b (mac80211: Fix tx queue
handling during scans) contains a bug that causes off-channel frames to
get queued when they should be handed down to the driver for transmit.
Prevent this from happening.
Reported-by: NFabio Rossi <rossi.f@inwind.it>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Unicast frame with unknown forwarding information always trigger
the path discovery assuming destination is always located inside the
MBSS. This patch allows the forwarding to look for mesh gate if path
discovery inside the MBSS has failed.
Reported-by: NCedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ieee80211_beacon_add_tim() function might be called
by drivers with BHs enabled, which causes a potential
deadlock if TX happens at the same time and attempts to
lock the tim_lock as well. Use spin_lock_bh to fix it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's various code with strange indentation,
questionable loop and locking constructs, etc.

The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Previously, the entire mesh beacon would be generated each
time the beacon timer fired. Instead generate a beacon
head and tail (so the TIM can easily be inserted when mesh
power save is on) when starting a mesh or the MBSS
parameters change.

Also add a mutex for protecting beacon updates and
preventing leaks.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to use _irqsave() as the lock
is never used in interrupt context.

This also fixes a problem in the iwlwifi MVM
driver that calls spin_unlock_bh() within its
set_tim() callback.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In my commit 1672c0e3
("mac80211: start auth/assoc timeout on frame status")
I broke auth/assoc timeout handling: in case we wait
for the TX status, it now leaves the timeout field set
to 0, which is a valid time and can compare as being
before now ("jiffies"). Thus, if the work struct runs
for some other reason, the auth/assoc is treated as
having timed out.

Fix this by introducing a separate "timeout_started"
variable that tracks whether the timeout has started
and is checked before timing out.

Additionally, for proper TX status handling the change
requires that the skb->dev pointer is set up for all
the frames, so set it up for all frames in mac80211.
Reported-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When sending a broadcast while at least on of the connected stations is
sleeping, it gets queued and send after a DTIM beacon is sent.
If the packet was to be sent on a vlan interface, the vif used for dequeing
from the per-bss queue does not hold the per-vlan sdata. The correct sdata is
required to use the correct per-vlan broadcast/multicast key.

This patch fixes this by restoring the per-vlan sdata using the skb->dev entry.
Signed-off-by: NMichael Braun <michael-dev@fami-braun.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.

To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.

This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods

Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.

Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.

Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.

Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).

Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.

Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.

Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: NMarco Porsch <marco@cozybit.com>
Signed-off-by: NIvan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: NMike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we had a connection for WoWLAN and after resume it
needed to be disconnected, the previous commit enabled
sending a deauth frame to the AP. This frame would not
go through on MFP-enabled networks as the key for it is
marked tainted before the frame is transmitted.

Allow a tainted key to be used for deauth frames. Worst
case, we'll use a wrong key because the PTK was rekeyed
while suspended, but more likely the PTK is still fine
and the taint flag really only applies to the GTK(s).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

gcc cannot prove that the value of sdata->vif.type does not
change between the switch() statement and the second
comparison to NL80211_IFTYPE_AP, causing a harmless
warning.
Slightly reordering the code makes the warning go away
with no functional change.

Without this patch, building ARM at91sam9g45_defconfig with
gcc-4.6 results in:

net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit':
net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This functions will be used for mesh beacons, too.
Signed-off-by: NMarco Porsch <marco@cozybit.com>
[some formatting fixes]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel contexts are not always used with monitor interfaces. If no channel
context is set, use the oper channel, otherwise tx fails.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[check local->use_chanctx]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of allocating a temporary buffer to build IEs
build them right into the SKB.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

One error path in ieee80211_subif_start_xmit() will
double-free the SKB. Set it to NULL to prevent that.

This issue was introduced by my channel context
changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:

+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+         ps = &sdata->u.mesh.ps;

Some references to the AP's beacon structure are removed where they
were obviously not used.

The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.

This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.

Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.

Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.

[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A few places free skbs using dev_kfree_skb even though they're called
after ieee80211_subif_start_xmit might have cloned it for tracking tx
status. Use ieee80211_free_txskb here to prevent skb leaks.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.
Reported-by: NCedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to carry around a return value
that is always NETDEV_TX_OK anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In ieee80211_beacon_get_tim() we can use the
txrc.sband instead of a separate local variable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.

[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of memset().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since we only need the band, remove the channel
pointer from struct ieee80211_tx_data and also
assign it properly, depending on context, to the
correct operating or current channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.

Add the appropriate parameters to respect the difference.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.

This patch make it always accept non-robust management frames.
Signed-off-by: NNicolas Cavallari <cavallar@lri.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>