Merge tag 'mac80211-next-for-davem-2019-08-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg:

====================
Here are a few groups of changes:
 * EDMG channel support (60 GHz, just a single patch)
 * initial 6/7 GHz band support (Arend)
 * association timestamp recording (Ben)
 * rate control improvements for better performance with
   the mt76 driver (Felix)
 * various fixes for previous HE support changes (John)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add devlink-trap support

This patchset adds devlink-trap support in mlxsw.

Patches #1-#4 add the necessary APIs and defines in mlxsw.

Patch #5 implements devlink-trap support for layer 2 drops. More drops
will be added in the future.

Patches #6-#7 add selftests to make sure that all the new code paths are
exercised and that the feature is working as expected.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test generic devlink-trap functionality over mlxsw. These tests are not
specific to a single trap, but do not check the devlink-trap common
infrastructure either.

Currently, the only test case is device deletion (by reloading the
driver) while packets are being trapped.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.

The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the trap IDs used to report layer 2 drops.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.

On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now the action of a trap was never changed during its lifetime.
This is going to change by subsequent patches that will allow devlink to
control the action of certain traps.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.

The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.

In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.

To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.

At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the first supported rate instead of 0 (which can be invalid)
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-3-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.

To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The group number needs to be multiplied by the number of rates per group
to get the full rate index

Fixes: 5935839a ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.nameSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.

Introduce new NL attributes that are needed for enabling and
configuring EDMG support.

Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.

Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG

New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: NAlexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.

fixes commit 697f6c50 ("mac80211: propagate HE operation info into
bss_conf")

This was reported by the static code checker.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Report timestamp for when sta becomes associated.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Report timestamp of when sta became associated.

This is the boottime clock, units are nano-seconds.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-1-greearb@candelatech.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

For the new 6GHz band the same rules apply for mandatory rates so
add it to set_mandatory_flags_band() function.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-9-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The default mandatory rates, ie. when not specified by user-space, is
determined by the band. Select 11a rateset for 6GHz band.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-8-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The function cfg80211_ir_permissive_chan() is applicable for
6GHz band as well so make sure it is handled.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-7-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In nl80211.c there is a policy for all bands in NUM_NL80211_BANDS and
in trace.h there is a callback trace for multicast rates which is per
band in NUM_NL80211_BANDS. Both need to be extended for the new
NL80211_BAND_6GHZ.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-6-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Add 6GHz operating class range as defined in 802.11ax D4.1 Annex E.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-5-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Extend the functions ieee80211_channel_to_frequency() and
ieee80211_frequency_to_channel() to support 6GHz band according
specification in 802.11ax D4.1 27.3.22.2.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-4-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

For the new 6GHz there are new UNII band definitions as listed
in the FCC notice [1].

[1] https://docs.fcc.gov/public/attachments/FCC-18-147A1_Rcd.pdfReviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-3-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

In the 802.11ax specification a new band is introduced, which
is also proposed by FCC for unlicensed use. This band is referred
to as 6GHz spanning frequency range from 5925 to 7125 MHz.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NLeon Zegers <leon.zegers@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-2-git-send-email-arend.vanspriel@broadcom.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The code generating the Tx Radiotap header when using tx_status_ext was
missing a field increment after setting the VHT bandwidth.

Fixes: 3d07ffca ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-4-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

When reporting 80MHz, we need to set 4 and not 2 inside the corresponding
field inside the Tx Radiotap header.

Fixes: 3d07ffca ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-3-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

When reporting legacy rates inside the TX Radiotap header we need to split
the check between "uses tx_statua_ext" and "is legacy rate". Not doing so
would make the code drop into the !tx_status_ext path.

Fixes: 3d07ffca ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-2-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

The RX Radiotap header length was not calculated properly when reporting
legacy rates using tx_status_ext.

Fixes: 3d07ffca ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: NJohn Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-1-john@phrozen.orgSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Saeed Mahameed says:

====================
mlx5-updates-2019-08-15

This patchset introduces changes in mlx5 devlink health reporters.
The highlight of these changes is adding a new reporter: RX reporter

mlx5 RX reporter: reports and recovers from timeouts and RX completion
error.

1) Perform TX reporter cleanup. In order to maintain the
code flow as similar as possible between RX and TX reporters, start the
set with cleanup.

2) Prepare for code sharing, generalize and move shared
functionality.

3) Refactor and extend TX reporter diagnostics information
to align the TX reporter diagnostics output with the RX reporter's
diagnostics output.

4) Add helper functions Patch 11: Add RX reporter, initially
supports only the diagnostics call back.

5) Change ICOSQ (Internal Operations Send Queue) open/close flow to
avoid race between interface down and completion error recovery.

6) Introduce recovery flows for RX ring population timeout on ICOSQ,
and for completion errors on ICOSQ and on RQ (Regular receive queues).

7) Include RX reporters in mlx5 documentation.

8) Last two patches of this series, are trivial fixes for previously
submitted patches on this release cycle.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-08-20

This series contains updates to ice driver only.

Brett fixes the detection of a hung transmit ring by checking the
software based tail (next_to_use) to determine if there is pending work.
Updates the driver to assume that using more than one receive queue per
receive ring container is a rare case, so use unlikely() in the case
were we actually need to divide our budget for multiple queues.  Fixed
an issue where the write back on ITR bit was not being set when
interrupts are disabled, which was causing only write backs when polling
only when a cache line is filled.  Cleans up unnecessary wait times
during VF bring up and reset paths.  Increased the mailbox size for
receive queues that are used to communicate with VFs to accommodate the
large number of VFs that the driver can support.

Akeem restructures the initialization flows for VFs, including how VFs
are configured and resources allocated to improve flows so that when we
clean up resources, we do not try to free resources that were never
allocated.  Organizes code to ensure that VF specific code is located in
the SR-IOV specific file.

Paul fixes an issue when setting the pause parameter which was
incorrectly blocking users from changing receive or transmit pause
settings.  Ensure register access for MSIX vector index is only done in
the PF space and not absolute device space.

Usha fixes a potential kernel hang in the DCB rebuild path when in CEE
mode, where the ETS recommended DCB configuration is not being set or
set correctly.

Mitch updates the driver to process all receive descriptors, regardless
of the size of the associated data.

Tony fixes and issue during the reset/rebuild path of a PF VSI where we
were assuming that the PF VSI was always to be enabled, which can
attempt to bring up a PF VSI on a downed interface which can lead to
various crashes.

Pawel fixes up variable definitions to match the type of data being
stored.

v2: Dropped patch 1 of the series to add ethtool support to query/add
    channels on a VSI, while we re-qork the functionality to match the
    ethtool expected behavior to report combined (Tx and Rx) numbers.
v3: Updated patch 4 to use kzalloc() and kfree() instead devm_kzalloc()
    and devm_kfree().
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we fail to add/delete MAC filters in the VF, the print doesn't
distinguish between the two. Fix that by printing whether or not we
failed to add/delete the MAC filter respectively.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These queue variables are being assigned values that are type u16.
Change the local variables to match these types. Since these
represent queue counts, they should never be negative.
Signed-off-by: NPawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to use some of the VF resources definition in the SR-IOV specific
virtchnl header file, this patch moves applicable code to
ice_virtchnl_pf.h file accordingly... and they should have been defined in
the destination file originally.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we use the ICE_MBXQ_LEN for both the Mailbox send and receive
queues that are used to communicate with VFs. This is fine for the send
queue because the PF driver will lock the queue for every single send,
but for the Mailbox receive queue every VF is posting to its Mailbox
send queue and the hardware is then handing the message to the PF on its
Mailbox receive queue. This becomes a problem with many VFs because it
seems to overburden the Mailbox receive queue on the PF. Fix this by
increasing the Mailbox receive queue for the PF to 512 entries.

The number 512 was determined based on the number of VFs supported by
the device. We can have a total of 256 VFs so in the worst case this
allows the VFs to put 2 messages in the PFs Mailbox receive queue at the
same time.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there are a couple places where the VF is waiting too long when
checking the status of registers. This is causing the AVF driver to
spin for longer than necessary in the __IAVF_STARTUP state. Sometimes
it causes the AVF to go into the __IAVF_COMM_FAILED, which may retrigger
the __IAVF_STARTUP state. Try to reduce the chance of this happening by
removing unnecessary wait times in VF bringup/resets.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Register access for GLINT_DYN_CTL and GLINT_VECT2FUNC should be within
the PF space and not the absolute device space.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During rebuild ice_ena_vsi() is called to recover the VSI state.
This function assumes the PF VSI is always to be enabled, however,
it's possible that during reset/rebuild the interface can be
brought down.  If this occurs, we can attempt to bring up the PF
VSI on a downed interface which can lead to various crashes. If
the interface is not running, do not bring up the associated VSI.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, the hardware will hand us a receive descriptor
which has no data attached, but is otherwise valid. The receive code was
improperly ignoring these descriptors, which result in an infinite loop.

To fix this, change the receive code to process all descriptors,
regardless of the size of the associated data. Add checks to the
memory-handling functions to allow for zero size.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the set local MIB AQ call failures in the DCB rebuild path
by setting the defaults for the ETS recommended DCB configuration. Also,
willing bits for the DCB configuration needs to be set correctly. Resets
works fine in IEEE mode as the ETS recommended DCB configuration is
populated but not in CEE mode.
Without this patch, PFR causes the kernel hang in CEE mode.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>