The vb2 framework knows if streaming is in progress, no need to use
a separate field for that.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The width, height and field values are core fields since both vbi, video
and blackbird use the same video input.

Move those fields to the correct struct.

Also fix the field checks in the try_fmt functions: add V4L2_FIELD_SEQ_BT/TB
support and map incorrect field values to a correct field value instead of
returning an error.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

There is no reason to dump the sram code to the kernel log when you
stop streaming. Remove those calls to cx88_sram_channel_dump.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The timeout is way too small. Especially complicated command like
CX2341X_ENC_STOP_CAPTURE takes much more time than 10 ms. Increase the
timeout to 1 second, just as ivtv does (the cx88-blackbird has the
same IP core for MPEG compression as ivtv).

This solves a nasty issue where STOP_CAPTURE would timeout and the
mailbox is left in a busy state, making it impossible to start streaming
a second time without reloading the driver first.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

btcx-risc is for the bt8xx driver and other drivers shouldn't depend
on it. There is no benefit to use that module just to do a
pci_zalloc_consistent.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove this function. This makes all vb2 queues behave the same, which
simplifies comparing the various vb2 queue op implementations.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Don't return -1, return a proper error.

Replace dprintk(0, ...) by pr_err since firmware load errors should just be
reported as an error.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/pci/cx88/cx88-blackbird.c:476:25: warning: cast to restricted __le32
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and
video the changes are all over.

What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.

Much simpler and more robust.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This list is only used if the width, height and/or format of a buffer has
changed, but that can never happen. Remove it and all associated code.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a duplicate of dev->fmt and can be removed. As a consequence a
lot of tests that check if the format has changed midstream can be
removed as well: the format cannot change midstream, so this is a bogus
check.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The only remaining place that modifies the relevant bit is in function
cx231xx_set_Colibri_For_LowIF
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The scanning itself just fails (as before this series) but now
the correct busses are scanned.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.

Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and
I2C_1_MUX_3, letting the I2C core handling the switch.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

change almost all instances of I2C_1 to I2C_1_MUX_3

Only these cases are changed to I2C_1_MUX_1:
* All that have dont_use_port_3 set.
* CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3.
* eeprom access for 930C
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Get used i2c port from bus_nr and status of port_3 switch.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is used later for is_tuner function that switches i2c behaviour for
some tuners.

[mchehab@osg.samsung.com: Fix CodingStyle on a multi-line comment]
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate
muxed i2c adapters.

Map mux adapters to I2C_1 for now.

Add local variables for i2c_adapters in dvb_init to get line lengths
shorter.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace numbers by the constants of same value and same meaning.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change to I2C_0 ... I2C_2 for the master ports
and add I2C_1_MUX_1 and I2C_1_MUX_3 for the muxed ones.

V2: Renamed mux adapters to seperate them from master adapters.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of using the same name for all 3 i2c physical buses
inside cx231xx, name them differently, adding a number
to it. This helps to better deal with the logs.

[mchehab@osg.samsung.com: removed an unused bus_name var from
 the original patch]
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

For each i2c master there is a i2c_client allocated that could be
deleted now that its only two users have been changed to use their
own i2c_client.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for deleting the otherwise useless i2c_clients
that are allocated for all the i2c master adapters.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

lockdep reports a potential circular dependecy deadlock when registering input device.

Unlock mutex rc_dev->lock prior to calling ir_raw_event_register to avoid the circular
dependency since that function also calls input_register_device and rc_open.

 ======================================================
 [ INFO: possible circular locking dependency detected ]
 3.17.0-rc7+ #24 Not tainted
 -------------------------------------------------------
 modprobe/647 is trying to acquire lock:
  (input_mutex){+.+.+.}, at: [<ffffffff812ed81c>] input_register_device+0x2ba/0x381

 but task is already holding lock:
  (ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190

 which lock already depends on the new lock.

[cut text]

 other info that might help us debug this:

 Chain exists of:
   input_mutex --> &dev->lock --> ir_raw_handler_lock

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(ir_raw_handler_lock);
                                lock(&dev->lock);
                                lock(ir_raw_handler_lock);
   lock(input_mutex);

  *** DEADLOCK ***

 4 locks held by modprobe/647:
  #0:  (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11
  #1:  (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11
  #2:  (&dev->lock){+.+.+.}, at: [<ffffffff81317fff>] rc_register_device+0x55d/0x58a
  #3:  (ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190

 stack backtrace:
 CPU: 0 PID: 647 Comm: modprobe Not tainted 3.17.0-rc7+ #24

 Call Trace:
  [<ffffffff81489d6a>] dump_stack+0x46/0x58
  [<ffffffff81487699>] print_circular_bug+0x1f8/0x209
  [<ffffffff81074353>] __lock_acquire+0xb54/0xeda
  [<ffffffff81080f17>] ? console_unlock+0x34d/0x399
  [<ffffffff81074c01>] lock_acquire+0xd9/0x111
  [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
  [<ffffffff8148e650>] mutex_lock_interruptible_nested+0x57/0x381
  [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
  [<ffffffff81124e03>] ? kfree+0x7c/0x96
  [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381
  [<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf
  [<ffffffff812ed81c>] input_register_device+0x2ba/0x381
  [<ffffffff8131a537>] ir_mce_kbd_register+0x109/0x139
  [<ffffffff81318728>] ir_raw_event_register+0x13d/0x190
  [<ffffffff81317e40>] rc_register_device+0x39e/0x58a
  [<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf
  [<ffffffffa00cf2e3>] nvt_probe+0x5ad/0xd52 [nuvoton_cir]
  [<ffffffffa00ced36>] ? nvt_resume+0x80/0x80 [nuvoton_cir]
  [<ffffffff81296003>] pnp_device_probe+0x8c/0xa9
  [<ffffffff812d1b94>] ? driver_sysfs_add+0x6e/0x93
  [<ffffffff812d203a>] driver_probe_device+0xa1/0x1e3
  [<ffffffff812d217c>] ? driver_probe_device+0x1e3/0x1e3
  [<ffffffff812d21ca>] __driver_attach+0x4e/0x6f
  [<ffffffff812d075b>] bus_for_each_dev+0x5a/0x8c
  [<ffffffff812d1b24>] driver_attach+0x19/0x1b
  [<ffffffff812d1879>] bus_add_driver+0xf1/0x1d6
  [<ffffffff812d2817>] driver_register+0x87/0xbe
  [<ffffffffa0120000>] ? 0xffffffffa0120000
  [<ffffffff81295da4>] pnp_register_driver+0x1c/0x1e
  [<ffffffffa0120010>] nvt_init+0x10/0x1000 [nuvoton_cir]
  [<ffffffff8100030e>] do_one_initcall+0xea/0x18c
  [<ffffffff8111497f>] ? __vunmap+0x9d/0xc7
  [<ffffffff810a3ca1>] load_module+0x1c21/0x1f2c
  [<ffffffff810a0bce>] ? show_initstate+0x44/0x44
  [<ffffffff810a404e>] SyS_init_module+0xa2/0xb1
  [<ffffffff81490ed2>] system_call_fastpath+0x16/0x1b
Signed-off-by: NTomas Melin <tomas.melin@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patches fixes an ancient bug in the dvb_usb_af9005 driver, which
has been reported at least in the following threads:
https://lkml.org/lkml/2009/2/4/350
https://lkml.org/lkml/2014/9/18/558

If the driver is compiled in without any IR support (neither
DVB_USB_AF9005_REMOTE nor custom symbols), the symbol_request calls in
af9005_usb_module_init() return pointers != NULL although the IR
symbols are not available.

This leads to the following oops:
...
[    8.529751] usbcore: registered new interface driver dvb_usb_af9005
[    8.531584] BUG: unable to handle kernel paging request at 02e00000
[    8.533385] IP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d
[    8.535613] *pde = 00000000
[    8.536416] Oops: 0000 [#1] PREEMPT PREEMPT DEBUG_PAGEALLOCDEBUG_PAGEALLOC
[    8.537863] CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc6-00151-ga5c075cf #1
[    8.539827] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[    8.541519] task: 89c9a670 ti: 89c9c000 task.ti: 89c9c000
[    8.541519] EIP: 0060:[<7d9d67c6>] EFLAGS: 00010206 CPU: 0
[    8.541519] EIP is at af9005_usb_module_init+0x6b/0x9d
[    8.541519] EAX: 02e00000 EBX: 00000000 ECX: 00000006 EDX: 00000000
[    8.541519] ESI: 00000000 EDI: 7da33ec8 EBP: 89c9df30 ESP: 89c9df2c
[    8.541519]  DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[    8.541519] CR0: 8005003b CR2: 02e00000 CR3: 05a54000 CR4: 00000690
[    8.541519] Stack:
[    8.541519]  7d9d675b 89c9df90 7d992a49 7d7d5914 89c9df4c 7be3a800 7d08c58c 8a4c3968
[    8.541519]  89c9df80 7be3a966 00000192 00000006 00000006 7d7d3ff4 8a4c397a 00000200
[    8.541519]  7d6b1280 8a4c3979 00000006 000009a6 7da32db8 b13eec81 00000006 000009a6
[    8.541519] Call Trace:
[    8.541519]  [<7d9d675b>] ? ttusb2_driver_init+0x16/0x16
[    8.541519]  [<7d992a49>] do_one_initcall+0x77/0x106
[    8.541519]  [<7be3a800>] ? parameqn+0x2/0x35
[    8.541519]  [<7be3a966>] ? parse_args+0x113/0x25c
[    8.541519]  [<7d992bc2>] kernel_init_freeable+0xea/0x167
[    8.541519]  [<7cf01070>] kernel_init+0x8/0xb8
[    8.541519]  [<7cf27ec0>] ret_from_kernel_thread+0x20/0x30
[    8.541519]  [<7cf01068>] ? rest_init+0x10c/0x10c
[    8.541519] Code: 08 c2 c7 05 44 ed f9 7d 00 00 e0 02 c7 05 40 ed f9 7d 00 00 e0 02 c7 05 3c ed f9 7d 00 00 e0 02 75 1f b8 00 00 e0 02 85 c0 74 16 <a1> 00 00 e0 02 c7 05 54 84 8e 7d 00 00 e0 02 a3 58 84 8e 7d eb
[    8.541519] EIP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d SS:ESP 0068:89c9df2c
[    8.541519] CR2: 0000000002e00000
[    8.541519] ---[ end trace 768b6faf51370fc7 ]---

The prefered fix would be to convert the whole IR code to use the kernel IR
infrastructure (which wasn't available at the time this driver had been created).

Until anyone who still has this old hardware steps up an does the conversion,
fix it by not calling the symbol_request calls if the driver is compiled in
without the default IR symbols (CONFIG_DVB_USB_AF9005_REMOTE).
Due to the IR related pointers beeing NULL by default, IR support will then be disabled.

The downside of this solution is, that it will no longer be possible to
compile custom IR symbols (not using CONFIG_DVB_USB_AF9005_REMOTE) in.

Please note that this patch has NOT been tested with all possible cases.
I don't have the hardware and could only verify that it fixes the reported
bug.
Reported-by: NFengguag Wu <fengguang.wu@intel.com>
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Cc: <stable@vger.kernel.org>
Acked-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBSky T9580 uses Integrated CX23885 IR controller to decode IR signal.
The IR type of DVBSky remote control is RC5.
Signed-off-by: NNibble Max <nibble.max@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add CI support for DVBSky T980C card. The new host device independent CIMaX SP2 I2C driver was used to implement it.

IRQ handling is not implemented at this point. It could be used to detect the CAM insertion/removal instantly.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

If the CI chip has an I2C driver, we need to store I2C client into state.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Improve debugging output.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Incorrect struct used in the SP2 driver.
Reported-by: NMax Nibble <nibble.max@gmail.com>
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds basic support for DVBSky T980C card. CI interface is not supported.

DVBSky T980C is a PCIe card with the following components:
- CX23885 PCIe bridge
- Si2168-A20 demodulator
- Si2158-A20 tuner
- CIMaX SP2 CI chip

The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI:
https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.htmlSigned-off-by: NOlli Salonen <olli.salonen@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace the use of nested functions where a normal function will suffice.

Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.

This code now works for both gcc and clang.
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBehan Webster <behanw@converseincode.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The au0828 quirks table is currently not in sync with the au0828
media driver.

Syncronize it and put them on the same order as found at au0828
driver, as all the au0828 devices with analog TV need the
same quirks.

Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add a macro to simplify au0828 quirk table. That makes easier
to check it against the USB IDs at drivers/media/usb/au0828/au0828-cards.c.

Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Set the property for delivery system also in case of SYS_DVBC_ANNEX_B.
This behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This field is not used on this driver anymore. Remove it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch partially reverts 0fb220f2. What happened is
that the conversion of debug messages to use pr_debug() was a
bad idea, because one needing to debug would need to both
enable debug level via a modprobe parameter, and then to
enable the dynamic printk's.

So, for now, let's use printk() directly at dprintk().
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>